3M 4295 FS Bedienungsanleitung

4295 FS Pole Mount Cabinet

Instructions

June 2001

78-8130-5228-5-A

1.0 General

1.1 The 3M™4295 FS Pole Mount Cabinet is used specifically for “Walk Up” pole mount

applications. It can be used for new construction and for rehabilitation or expansion of frames

from existing cabinets because the cabinet has top and bottom split cable ports. Up to 2700 cable

pairs of 3M™4220 Self-Strip Termination Blocks can be loaded into the Cabinet. The Blocks

are preterminated with either 3M™MS2Modules or 3M™710 Connectors.

1.2 Use of this cabinet for rehabilitation and expansion is covered in Section 9.0 of this instruction.

1.3 Instructions for running jumpers, installation of Priority Caps and the use of the included Test

Probe are on the inside of the cabinet door.

2.0 Cabinet Dimensions and Parts Identification

13 3/4”

44 1/4”

28 3/4”

60”

57 3/4”

Test Probe

with Holder

3-SS9KN (Self-Strip Blocks, 900 Pair K Height, Narrow) Frames

Cable Ground Bar

Jumper Wireway Self-Strip Block

Assemblies

4295 FS Top Mount Bracket 4295 FS Bottom Mount Bracket

3.0 Accessories

3.1 Jumper Wire Spools –

4268 - 800 ft. 22 AWG violet/white jumper wire

4368 - 800 ft. 22 AWG red/white jumper wire

4068 - 800 ft. 24 AWG orange/white jumper wire

3.2 4324 Priority Cap for Self-Strip Blocks

3.3 4320 Self-Strip Caps (100 tan & 100

orange)

3.4 4295-SPK Small Port Kit (2-5/8")

3.5 4295-MPK Medium Port Kit (3-3/8")

3.6 4295-LPK Large Port Kit (4")

3.7 PST 4634R (use with 2 5/8" ports)

3.8 PST 4635R (use with 3 3/8" and 4" ports)

3.9 4097-F Flanged Gland Kit (2 5/8" dia.)

3.10 4097-BF Flanged Gland Kit (3 3/8" dia.)

3.11 4075-S or 4077 Series Sealant Boxes

Test Probes

3.12 4327 Self-Strip Single-Pair Probe

3.13 4327-P Self-Strip Pocket Probe

3.14 4328 Self-Strip 25-Pair Test Connector

4.0 Cabinet Mounting

4.1 Attach the Top and Bottom Pole Mount Brackets according to the drawings. The flat slotted edge

of the Bottom Bracket is up. Make sure that the Bottom Bracket is aligned and plumb with the

Top Bracket or it could affect the operation of the doors. Follow your company's "pole mounting

hardware" practice. When required, adjust these dimensions to meet your company practice or

local conditions.

Top and

Bottom

brackets

must be in

alignment

37”

63 1/2”

Ground Line

57 3/4”

15”

4.2 Raise the lifting brackets on the top of the

Cabinet and attach a sling to them. Lift it

into position with a boom truck. The Top

Mounting Bracket supports the Cabinet's

hanging weight.

4.3 The Cabinet’s Bottom Brackets use the

bracket's slotted holes to make side-to-side,

tilt and up and down adjustments as needed.

Secure the Cabinet to the pole by tightening

the bolts of the Bracket.

4.4 Attach the cable to the pole per your

company's practice.

5.0 Cable Preparation

Note: Two 3 3/8" and one 2 5/8" Metal Cable Ports are included with the cabinet. Slide the

appropriate sized port over the cable(s) before attaching the cable(s) in the cabinet. An optional 4"

Metal Cable Port can be ordered if needed.

5.1 Open Cabinet doors, loosen frame-retaining screws and remove frames by lifting the

bottom up and out of the cabinet.

5.2 Cable Entry

a.) For top entry cable(s), remove the Cabinet’s Top Front Port Plate, the Top Center Frame

Mount Bracket and the Metal Port Covers(s) on the top of the Cabinet.

b.) For bottom entry cable(s), remove the Bottom Front Port Plate, the Bottom Jumper Wire

Trough and the Metal Port Covers(s) on the bottom of the Cabinet.

5.3 Remove the cable sheath 3" beyond the first Cable Tie Bar leaving a minimum of 12 feet of free

conductor in the Cabinet.

5.4 Follow your company procedure to install shield bond connector(s) and bond strap(s) long

enough to reach the Cabinet’s Bond Plate. Identify the cable binder groups.

6.0 Cable Port Seal

6.2 Scuff and round out the area of sheath where the

sealing tape and port will be located.

6.3 Slide the PST, (pull cord must be opposite

the cabinet) the steel port and gasket over the

cable and out of the Cabinet.

6.4 Wrap the sealing tape approximately 1" away

from the Cabinet’s top or bottom, so it will

center the cable in the port. Position and

install the gasket and port to the Cabinet as

shown in the drawing.

6.5 Build an even transition from the port

to the cable with more sealing tape.

7.0 Cable Termination

7.1 Separate the Feeder and Distribution count of

the cable(s) into 100 pair groups. Route the

groups to the tie bars to the appropriate frame

location according to frame count.

a.) It is recommended that the Feeder count is in

the center blocks and the Distribution count

blocks are on the sides of the Feeder blocks in

the Cabinet.

Distribution

451

Distribution

450

Distribution

900

1-Feeder 451-Feeder

Feeder

900

Feeder

450

901

Distribution

1351

Distribution

1350

Distribution

1800

3M™4295 FS 2700 Pair Cabinet

6.1 Two 3 3/8" and one 2 5/8" Metal Cable Ports are included with the Cabinet. Use the appropriate sized

port for the cable(s) in the Cabinet. An optional 4” Metal Cable Port can be ordered if needed. The Kits

include a port, sealing tape and a collapsible tube called the 3M™Pull-N-Shrink Tube (PST).

6.6 Install the PST over the tape and port. Unwind the pull cord of the PST counter clockwise until the

tube is collapsed and the core is removed.

6.7 Wrap entire PST with two half-lapped layers of 3M™88T Vinyl Tape or equivalent.

6.8 Secure the cable(s) to the Cable Tie Bar.

6.9 Attach the bond strap(s) to the Bond Plate and tie the strap(s) together and out of the way from the frame

and jumper trough. Record the bond strap(s) identification on the Cable Bond Label in the Cabinet.

6.10 Reinstall the Cabinet’s Port Plate, the Top Center Frame Mount Bracket or the Bottom Jumper Wire

Trough if removed.

3M™88T

7.2 For top entry cable(s), tie these groups to the farthest tie bar in the Cabinet. Bottom entry cable(s) can

either be tied off to the first bar or waterfall the groups at the upper bar and tie to the bottom bar for extra slack.

7.3 Reinstall one of the Cabinet’s Frames. Position the Frame on the bottom pivots and attach the

safety cord to the back of the Frame. Allow the Frame to rest at a 45˚ angle.

7.4 In this position, tie the appropriate groups to the bottom of the Frame.

7.5 Mount a splicing unit on the Frame and position it so the connections will be made behind the

blocks. The completed connections and cable slack can be stored in the trough.

7.6 Splice the block’s connectors/modules to cable per your company procedure. Tie and store the

cable groups and connectors/modules in the frame block trough.

Note: When splicing with dry 3M™MS2™ Modules, always install the proper sized Sealant Box.

When using 3M™MS2™ Modules, 3M™4075 or 4077 Series Sealant Boxes or 3M™710 Connectors

containing sealants, carefully follow safety, health and environmental information on the label or

the Material Safety Data Sheet.

7.7 Secure the Frame in the upright position with the screw at the top of the Frame. Repeat this

procedure with the next two Frames and complete the Cabinet splicing.

Top Entry/Frame Storage Bottom Entry

with slack frame stored

Bottom Entry,

no slack frame stored

8.0 Labeling

8.1 Remove protective tape from identification

pads on blocks.

8.2 Select proper sequence of labels (blue-

distribution; green-feeder) and detach strip

of 20 labels from sheet.

Note: 1-6-11 etc. are attached to the left side of

block and 5-10-15 etc. are attached to the

right side.

8.3 Carefully remove protective backing from

strip as shown.

8.4 Align strips of numbers with block

identification pads and press in place.

Carefully remove outer liner, leaving labels

on pads.

8.5 Fill in binding post log.

9.1 Rehabilitation

The 3M™4295 FS Pole Mount Cabinet can be used for rehabilitation of frames from existing

cabinets. The Cabinet’s top and bottom split cable entry ports makes it versatile so existing

cables and frames can be placed into the Cabinet’s opening of 13 3/4" deep x 45" high x 43” wide.

9.2 Expansion

The Cabinet can also be used to expand an existing frame with up to 900 cable pairs of 3M™4320 Self-

Strip Termination Blocks that are preterminated with either 3M™MS2Modules or 710 Connectors. The

existing frame can have dimensions up to 13 3/4" deep x 45" high x 28" wide.

IMPORTANT NOTICE

Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability

associated with such use.

Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture as of the date of

purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above,

your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except

where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect,

special, incidental or consequential regardless of the legal theory asserted.

Telecommunications

6801 River Place Blvd.

Austin, TX 78726-9000 Litho in USA

www.3M.com/telecom © 3M IPC 2001 78-8130-5228-5

9.0 Cabinet Rehabilitation and Expansion

43”

28”

45”

Inhaltsverzeichnis

Andere 3M Sicherheitsausrüstung Handbücher

3M DBI SALA Lineman's Belt Bedienerhandbuch

3M SafeClaw 4077 Bedienungsanleitung

3M DBI Sala Rollgliss R550 Bedienungsanleitung

3M 1901 Bedienungsanleitung

3M DBI SALA Nano-Lok Bedienungsanleitung

3M 70007438503 Bedienungsanleitung

3M PROTECTA 8008005 Bedienerhandbuch

3M Jupiter Powered Air Turbo Bedienungsanleitung

3M PROTECTA 3100418 Bedienungsanleitung

3M PROTECTA COBRA AC202/01 Bedienerhandbuch

3M Peltor X Series Bedienungsanleitung

3M DBI SALA Self-Rescue 3320030 Bedienerhandbuch

3M 3M-Matic S-857 Datenblatt

3M SEALED-BLOK 3400944 Bedienungsanleitung

3M DBI Sala Rollgliss R550 Bedienungsanleitung

3M DBI SALA FlexiGuard SafRig Bedienerhandbuch

3M DBI-SALA EXOFIT X100 Series Bedienungsanleitung

3M PROTECTA AM100 Bedienungsanleitung

3M DBI Sala Rollgliss Bedienerhandbuch

3M Protecta Rebel 3590610 Bedienungsanleitung

3M DBI SALA KM419 Bedienerhandbuch

3M DBI-SALA EZ-Line Bedienungsanleitung

3M DBI SALA LAD-SAF Bedienungsanleitung

3M Adflo Wartungshandbuch

Beliebte Sicherheitsausrüstung Handbücher anderer Marken

Innova

Innova Xtirpa Bedienungsanleitung

bolle SAFETY

bolle SAFETY B810 Bedienungsanleitung

SHENZHEN FANHAI SANJIANG ELECTRONICS

SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung

Hiltron security

Hiltron security POWER8E Leitfaden

Hatco

Hatco B-950P Bedienungsanleitung

Sitec

Sitec TX MATIC Bedienungsanleitung

TEUFELBERGER

TEUFELBERGER GRIP 12 Bedienungsanleitung

MSA

MSA PremAire System Bedienungsanleitung

AMC

AMC 1022M Series Bedienungsanleitung

Trinity

Trinity CASS S3 Bedienungsanleitung

CMC

CMC Helitack HotSeat Bedienungsanleitung

Force

Force P-35 Bedienungsanleitung

ACM

ACM SAFETY D200 Produkthandbuch

Honeywell

Honeywell Miller H-Design DuraFlex Bedienerhandbuch

ROCK

ROCK P-451 AS Bedienungsanleitung

Power first

Power first 2XYR7A Service-Handbuch

SCHUBERTH

SCHUBERTH SHP 28-C Bedienungsanleitung

Trango

Trango CINCH Bedienungsanleitung