3M Quick Term II Bedienungsanleitung
Quick Term II™
Hi-K Silicone Rubber Termination Kit, 15 kV
Instruction Sheet
Technical Information:
For use on 15 kV Tape or Wire Shielded Cable
Conductor Size Range:
#2 AWG-1000 kcmil
Primary Insulation O.D. Range:
.637”-1.810” (16.2-46.0 mm)
Hi-K Silicone Rubber Termination Kits
for
Tape or Wire Shielded Cable
15 kV Class
5671 5672
Number of Pages: 4
Issue Date: 9/9/97
Scale: Not to Scale
Issue: 78-8111-0842-8
DIMENSION TABLE
Kit No. AB15 kV Cond.
Size Range
(AWG - kcmil)
Primary Insul.
O.D. Range
(inch-mm)
5 6 71 10"
(254
mm) Depth of
Lug or #2 -2 50 .637-1.120"
(16.2-28.4 mm)
5 6 72 10"
(254
mm)
Stem
Connector
Barrel 250-I000 .940”-1.810”
(23.9-46.0 mm)
IEEE Std. No. 48, 1975
Class 3 Termination
15 kV Class
Kit Contents:
1 Hi-K Silicone Rubber Termination
1 Packet of Silicone Grease
1 Instruction Sheet
A. Prepare Cable
Check to be sure cable size fits within the kit range as shown in the dimensional table below.
1. TAPE SHIELD
a. Remove cable jacket, tape shielding, semi-con and insulation as shown in Figure 1 and
dimension table below. (Be sure to allow for depth of lug B).
b. Bind down the cable semi-con and tape shield with 2 half lapped layers of Scotch #13
Semi-Conductor Tape, starting 1/4” on tape shield to 1/4” onto cable connection. (Figure 2)
2. WIRE SHIELD
a. Remove jacket as shown in Figure 3 and dimension table below. (Be sure to allow
for depth of lug B)
b. Wrap 2 full wraps of Scotch 24 Shielding Tape over shielding wires at
jacket edge. Cut off excess 24 Tape. (Figure 3)
c. Bend shielding wires back over 24 tape and cut off excess at cable jacket edge. (Figure 3)
d. Remove cable semi-con as shown in Figure 3.
3. Remove cable insulation for a distance B.
4. CLEAN CABLE, USING STANDARD PRACTICE.
a. Wipe the cable insulation with a solvent such as 1.1.1 trichloroethane in the Scotch Brand
A-2 Cable Prep Kit or Scotch Brand A-3 Electrician’s Abrasive Roll.
b. If abrasive must be used:
1) Use on insulation only. DO NOT USE ON SEMI-CON MATERIAL.
2) Use only 120 grip aluminum oxide such as in A-2 Cable Prep Kit or Scotch Brand A-3
Electrician’s Abrasive Roll.
3) Be careful not to reduce the cable insulation diameter below that allowed by the kit.
B. Install Ground Strap
1. Unstrap 1 to 2 inches (25 to 50 mm) at coil.
2. Lay ground strap along cable with the extended coil facing downward (away from you)
(Figure 4). Note: Coil should be in contact with the cable shielding and coil edge should be
butted against cable jacket edge.
3. Hold coil in place with thumb. Pull coil around the cable allowing it to unwrap and rewrap
around the shielding and itself. (Figure 4). Note: Cinch (tighten) the applied coil after final
wrap.
C. Install Termination
1. Cover the edge of the 13 tape or semi-con material with a liberal coating of silicon grease.
(Figure 4) NOTE: ON THIS PRODUCT THE SILICONE GREASE DOES NOT SERVE AS A
LUBRICANT. IT MUST BE USED TO FILL THE STEP AT THE LEADING EDGE OF 13 TAPE
OR THE STEP AT THE SEMI-CON CUTOFF. Spread silicone grease over the entire exposed
primary insulation.
2. Slide the termination body onto the cable, (loose care end extending out toward cable lug)
aligning base with the edge of the constant force spring.
3. Remove termination core unwinding counterclockwise starting with the loose end. Make sure
the termination body is buffed up to the edge of the constant force spring (Figure 5). Note: An
occasional tug of the strand while unwinding will aid in care removal. Wipe off excess silicone
grease from the exposed insulation.
D. Install Lug or Connector
1. Install lug or connector per manufacturer’s instructions. See Crimping Table below when
using 3M type lugs.
NOTE: when installing in enclosed
switchgear or transformers maintain
clearances required by
manufacturers.
CRIMPING TABLE FOR 3M STEM TYPE CONNECTORS
Conductor 3M Stem Recommended Crimping Tools
Size Conn. No. Manufacturer Mech. Tool Die (No. Crimps) Hydraulic Tool Die (No. Crimps)
#1 Sol.
#1 ,#2
1/0
SC0002
SC0001
SC0010
BURNDY
KEARNY
T &B
ANDERSON
MD6
O-51,O-52
TBM8
-
BG(4).W-243(4)
5/8 (4)
OLIVE (2)
-
Y35,Y39,Y45**
TBM 15
VC 6
U25ART(2),U243(2)
50*(2)
UNIVERSAL (2)
2/0
3/0
4/0
SC0020
SC0030
SC0040
BURNDY
KEARNY
T &B
ANDERSON
MD6
O-51 ,O-52
TBM8
-
W660(3),840(5)
840(5)*
WHITE(4)
-
Y35,Y39,Y45**
WH-1 ,WH-2
TBM 15
VC 6
U28ART(2)
840(2)
66(3)
UNIVERSAL (2)
250 - 1000 kcmil Crimp According to Manufacturer's Directions
‘3M’, ‘Cold Shrink and ‘Scotchlok’ are trademarks of 3M
Important Notice to Purchaser:
All statements, technical information and recommendations related to the Seller’s products are based on information believed to be reliable, but
the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the product for its
intended use. The user assumes all risks and liability whatsoever in connection with such use.
Any statements or recommendations of the Seller which are not contained in the Seller’s current publications shall have no force or effect unless
contained in an agreement signed by an authorized officer of the Seller. The statements contained herein are made in lieu of all warranties expressed
or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which warranties are hereby
expressly disclaimed.
SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY INCLUDING BUT NOT LIMITED
TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES SUSTAINED OR
INCURRED BY REASON OF THE USE OF ANY OF THE SELLERS PRODUCTS.
Electrical Products Division
6801 River Place Blvd.
Austin, TX 78726-9000
Litho in USA
© 1997 3M
78-8111-0842-8
Andere 3M Sicherheitsausrüstung Handbücher
3M
3M WORKTUNES WIRELESS Bedienungsanleitung
3M
3M DBI SALA 2000005 Bedienerhandbuch
3M
3M DBI SALA 3101207 Bedienungsanleitung
3M
3M PROTECTA 3100418 Bedienungsanleitung
3M
3M DBI SALA NANO-LOK EDGE Bedienerhandbuch
3M
3M DBI SALA 8000124 Bedienerhandbuch
3M
3M 306S1043 Bedienungsanleitung
3M
3M DBI Sala Rollgliss R550 Bedienungsanleitung
3M
3M PROTECTA COBRA AC202/01 Bedienerhandbuch
3M
3M PELTOR WS LiteCom Plus Bedienungsanleitung
3M
3M DEUS 7300 Bedienungsanleitung
3M
3M W-3060 Bedienungsanleitung
3M
3M DBI-SALA EZ-Stop AJ512Y/0 Bedienungsanleitung
3M
3M DBI SALA Sealed-Blok 3400803 Bedienungsanleitung
3M
3M Protecta 1161200 Bedienungsanleitung
3M
3M DBI SALA EXOFIT X200 Bedienungsanleitung
3M
3M 6000 Bedienungsanleitung
3M
3M DBI SALA FlexiGuard SafRig Bedienerhandbuch
3M
3M NANO-LOK 3500276 Bedienungsanleitung
3M
3M DBI-SALA DELTA 1100675 Bedienungsanleitung
Beliebte Sicherheitsausrüstung Handbücher anderer Marken
Innova
Innova Xtirpa Bedienungsanleitung
bolle SAFETY
bolle SAFETY B810 Bedienungsanleitung
SHENZHEN FANHAI SANJIANG ELECTRONICS
SHENZHEN FANHAI SANJIANG ELECTRONICS A9060T Bedienungsanleitung
Hiltron security
Hiltron security POWER8E Leitfaden
Hatco
Hatco B-950P Bedienungsanleitung
Sitec
Sitec TX MATIC Bedienungsanleitung
