A-Neuvideo ANI-2PIP-LOGO Bedienungsanleitung

AUDIO / VIDEO MANUFACTURER

ANI-2PIP-LOGO

2x1 HDMI Multiviewer

INSTRUCTION MANUAL

A-NeuVideo.com

Frisco, Texas 75034

(469) 277-7606

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.

Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of re, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and

excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not

likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience

receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the

means of grounding of a piece of equipment is not defeated.

9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC

voltage is not covered by any warranty.

10. Turn power off and disconnect unit from AC current before making connections.

11. Never hold a power switch in the “ON” position.

12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use

the unit near stoves, heat registers, radiators, or other heat producing devices.

13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal

ow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky

environment, the unit should be periodically “blown free” of foreign dust and matter.

14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to

qualied service personnel. There are no user serviceable parts inside.

15. When moving the unit, disconnect input ports rst, then remove the power cable; nally, disconnect the interconnecting cables to

other devices.

16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,

use only the original factory packing.

19. Service Information Equipment should be serviced by qualied service personnel when:

A. The power supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the equipment.

C. The equipment has been exposed to rain.

D. The equipment does not appear to operate normally, or exhibits a marked change in performance.

E. The equipment has been dropped, or the enclosure damaged.

THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

TABLE OF CONTENTS

ANEUVIDEO

CONTENTS

INTRODUCTION & CONTENTS ...................................................1

FEATURES....................................................................................2

SPECIFICATIONS .........................................................................3

OPERATION CONTROLS & FUNCTIONS ..................................4

RS-232 PIN DEFINITION / TELNET CONTROL ............................5

RS-232 & TELNET COMMANDS ..................................................6

WEBGUI CONTROL ..................................................................12

CONNECTION DIAGRAM ...........................................................17

Dear Customer

Thank you for purchasing this product. For optimum performance

and safety, please read these instructions carefully before

connecting, operating or adjusting this product. Please keep this

manual for future reference.

INTRODUCTION

The ANI-2PIP-LOGO HDMI Multiviewer is capable of scaling up

to (2) sources and displaying both simultaneously on a single

HDMI output within their own windows. This is the ideal solution

for monitoring multiple sources simultaneously for use in control

rooms, or for exible display presentations in conference rooms or

classrooms. Both inputs support resolutions up to 1920x1200@60Hz

and LPCM audio with up to 7.1 channels at 192kHz.

The multi-window output is sent to a single HDMI output at scaled

resolutions up to 1920x1200@60Hz along with the selected audio

source. The HDMI output supports up to LPCM 7.1 digital audio

while the analog audio output supports up to LPCM 2.0. Each of

the (2) HDMI sources may be displayed individually, full screen,

or they can be displayed using a variety of dual-window modes

including Picture-in-Picture, Side-by-Side, or freely positioned (with

layer priority control). Each window can also be mirrored, ipped,

swapped, or frozen (with live audio). Chroma keying and a custom

uploadable logo/graphic are also supported.

External images can be uploaded and overlaid on top and at any

position on the live HDMI Output. This unit can be controlled easily

by use of the front panel controls (with OSD) as well as by WebGUI,

Telnet, RS-232, IR and (8) direct trigger inputs. This products have

a 3 year warranty.

PACKAGE CONTENTS

Before attempting to use this unit, please check the packaging and

make sure the following items are contained in the shipping carton:

• ANI-2PIP-LOGO HDMI Multiviewer

• 5V/2.6A DC Power Adapter

• (3) 5-pin Terminal Block

• Shockproof Feet (Set of 4)

• Users Guide

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or

operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of re,

electrical shock and injury to persons.

• To prevent re or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts

inside the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the

PSU if it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufcient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and

is believed to be accurate. We assume no responsibility for any

infringements of patents or other rights of third parties which may

result from its use.

We assume no responsibility for any inaccuracies that may be

contained in this document. We make no commitment to update or

to keep current the information contained in this document.

We reserve the right to make improvements to this document and/

or product at any time and without notice.

No part of this document may be reproduced, transmitted,

transcribed, stored in a retrieval system, or any of its part translated

into any language or computer le, in any form or by any means

— electronic, mechanical, magnetic, optical, chemical, manual, or

otherwise — without the express written permission and consent.

Version 1.2 JULY 2018

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

FEATURES

• HDMI & HDCP 1.3 compliant

• (2) HDMI inputs and (1) HDMI output

• Inputs and output support HD resolutions up to 1080p@60Hz and PC resolutions up to WUXGA (RB)

• Supports audio pass-through of LPCM 2.0/5.1/7.1 sources via HDMI

• Balanced analog stereo audio extraction support via 5-pin terminal block (LPCM 2.0 only)

• Supports PiP (Picture-in-Picture), Side-by-Side, and free positioning window modes

• Easy individual window size, position and layer priority adjustment

• Supports per-window mirror, ip and image freeze (w/ live audio) functionality

• Chromakey support

• Uploadable logo support

• Support for Windows PC character generation software to simplify the process of generating text or graphics to use with keying/

overlay (Optional)

• (8) Trigger inputs for easy remote control of the unit with optional keypad

• Supports front panel buttons (with OSD), WebGUI, Telnet, RS-232, IR and Trigger controls

APPLICATIONS

• Demo Room Displays

• Security Monitoring

• Hotel Lobby Information Displays

ANEUVIDEO

SYSTEM REQUIREMENTS

• HDMI source equipment such as media players, video game consoles or

set-top boxes.

• HDMI receiving equipment such as an HDTV, monitor, or audio amplier.

• Analog audio receiving equipment such as headphones, an audio amplier

or powered speakers.

SPECIFICATIONS

Specifications

• HDMI Bandwidth: 225MHz/6.75Gbps

• Input Ports: (2) HDMI

• Output Ports: (1) HDMI / (1) Stereo (Terminal Block)

• Control Interfaces:

• (8) Trigger (Terminal Block)

• RS-232 (9-pin D-sub)

• IP Control (RJ-45)

• Baud Rate: Up to 115200bps

• Power Supply: 5V/2.6A DC (US/EU standards, CE/FCC/UL certied)

• ESD Protection Human Body Model:

• ±8kV (Air Discharge)

• ±4kV (Contact Discharge)

• Dimensions (WxHxD): 9.1 x 1 x 4.25 in (231.5x25x108mm) [Case Only] 9.1 x 1 x 4.7 in (231.5x25x116mm) [All Inclusive]

• Weight: 1.4 lb/652g

• Chassis Material: Metal

• Silkscreen Color: Black

• Operating Temperature: 0˚C–40˚C/32˚F–104˚F

• Storage Temperature -20˚C–60˚C/-4˚F–140˚F

• Relative Humidity: 20–90% RH (Non-condensing)

• Power Consumption: 5.1W

As product improvements are continuous, specications are subject to change without notice.

Audio Specifications

• Max Audio Level: 2Vrms

• THD+N: < −86dB@0dBFS 1kHz (A-wt)

• SNR: >110dB@0dBFS

• Frequency Response: < ±3dB@20Hz~20kHz

• Crosstalk: < −100dB@10kHz

• Impedance: 47Ω

• Type: Balanced/Unbalanced

Cable Specifications

• HDMI Cable Length for 1080p - 8-bit & 12-bit:

• Input & Output: 32 ft/10 M

Video Specifications

Supported PC Resolution (Hz)

HDMI Input HDMI Output

640x480@60 800x600@60 1024x768@70 1280x1024@60 1600x1200@60 1024x768@60 1600x900@60 (RB)

640x480@72 800x600@72 1024x768@75 1360x768@60 1680x1050@60 1280x800@60 1600x1200@60

640x480@75 800x600@75 1024x768@85 1366x768@60 1920x1200@60 (RB) 1280x1024@60 1680x1050@60

640x480@85 800x600@85 1280x800@60 1440x900@60 1366x768@60

800x600@56 1024x768@60 1280x960@60 1600x900@60 1440x900@60

ANEUVIDEO

Operation controls & Functions

Front Panel

qSERVICE: This port is reserved for rmware update use only.

wPOWER LED: This LED will illuminate to indicate the unit is on and receiving power.

eSWITCH BUTTON: Press to toggle between the two HDMI inputs and output the selected source full screen.

NOTE: Press and hold this button for 2 seconds to change the output resolution to 1920x1080p@60Hz.

rMODE BUTTON: Press to sequentially switch between the Full Screen (NONE), Picture-in-Picture (PIP), Side-by-Side (SBS), and

Picture- outside-Picture (POP) windowing modes.

NOTE: Press and hold this button for 2 seconds to change the output resolution to 1024x768@60Hz.

tAUDIO BUTTON: Press to toggle between the audio from the (2) HDMI inputs.

yINFO. BUTTON: Short press to show the current input/output resolution status, audio selection and IP information. Long press to show

the current contrast, brightness, hue, sharpness, color format, chroma and color temperature settings for each source channel.

BACK Panel

qAUDIO OUT: Connect to powered speakers or an amplier for balanced stereo analog audio output.

wHDMI OUT: Connect to an HDMI TV, monitor or amplier for digital video and audio output.

eTRIGGER IN: This 10 pin terminal block provides (8) trigger pins (plus 5V & Ground) for activating pre-designated functions within the

unit. Compatible with the optional Trigger Keypad unit.

Pins are numbered from left to right:

TOP ROW BOTTOM ROW

1 Vcc (5V) 6 GROUND

2 POP Windowing Mode 7 Image Freeze (Toggle)

3 SBS Windowing Mode 8 Display Logo (Toggle)

4 PIP Windowing Mode 9 A/V Mute (Toggle)

5 Full Screen Window (Toggle) 10 Window Source Swap (Toggle)

rHDMI IN 1~2: Connect to HDMI source equipment such as media players, game consoles or set-top boxes.

tRS-232: Connect directly to a PC, laptop or other serial control device to send RS-232 commands to control the unit.

yCONTROL: Connect directly, or through a network switch, to your PC/laptop to control the unit via Telnet/WebGUI.

u DC 5V: Plug the 5V DC power adapter into the unit and connect it to an AC wall outlet for power.

ANEUVIDEO

RS-232 Pin Definition / Telnet Control

RS-232 Pin Definition

PIN ASSIGNMENT PIN ASSIGNMENT

1 NC 1 NC

2 TxD 2 RxD

3 RxD 3 TxD

4 NC 4 NC

5 GND 5 GND

6 NC 6 NC

7 NC 7 NC

8 NC 8 NC

9 NC 9 NC

Baud Rate: 110 ~ 921600

Data Bit: 8 bits

Parity: None

Stop Bit: 1 bit

Flow Control: None

Telnet Control

Before attempting to use Telnet control, please ensure that both the unit and the PC are connected to the same active networks.

O ACCESS THE COMMAND LINE INTERFACE (CLI)

Windows 7 Click START, type “cmd” in the search eld and press ENTER.

Windows XP Click START > RUN, type “cmd”, and press ENTER.

Mac OS X Click Go > Applications > Utilities > Terminal.

Once in the Command Line Interface (CLI) type “telnet” followed by the IP address of the unit (and the port number if it is non standard)

and then hit “Enter”. This will connect us to the unit we wish to control. Type “help” to list the available commands. See below for

reference.

NOTE: If the IP address is changed then the IP address required for Telnet access will also change accordingly.

ANEUVIDEO

RS-232 & Telnet Commands

COMMAND DESCRIPTION & PARAMETERS

DESCRIPTION & PARAMETERS

? 8Show the full command list.

HELP 8Show the full command list.

GET FW VER 8Show the unit’s current rmware version.

SET FACTORY DEFAULT 8Reset all congurations to the factory defaults.

SAVE PRESET N1 8Save the current conguration as preset N1.

N1 = 1 ~ 4 [Preset number]

RECALL PRESET N1 8Recall the saved conguration from preset N1.

N1 = 1 ~ 4 [Preset number]

SET OUT A ROUTE N1 8Switch to full screen routing mode and show input N1.

N1 = 1 ~ 2 [Input port]

GET OUT A ROUTE 8Show the currently set full screen routing source.

SET WINDOW LAYOUT MODE N1 8Set the windowing mode to N1.

Available values for N1:

1 [PIP mode]

2 [SBS mode]

4 [POP mode]

5 [Full screen routing mode]

GET WINDOW LAYOUT MODE 8Show the currently selected windowing mode.

SET OUT A WINDOW PRIORITY N1 Select which input window will have top display priority in the dual-windowing modes.

N1 = 1 ~ 2 [Input port]

GET OUT A WINDOW PRIORITY 8Show which input window currently has top display priority.

SET WINDOW SWAP N1 8Enable or disable the input window swap function.

Available values for N1:

0 [Off]

1 [On]

GET WINDOW SWAP 8Show the current state of the window swap function.

SET IN AUTO MODE N1 8Enable or disable the auto input switching mode.

Available values for N1:

0 [Off]

1 [On]

GET IN AUTO MODE 8Show the current state of the auto input mode.

SET IN N1 EDID N2 8Set the EDID to use with input N1.

N1 = 1 ~ 2 [Input port]

Available values for N2

1 [Internal EDID 1]

2 [Internal EDID 2]

GET IN N1 EDID 8Show the EDID source currently used by input N1.

N1 = 1 ~ 2 [Input port]

ANEUVIDEO

RS-232 & Telnet Commands

RS-232 Commands

COMMAND DESCRIPTION & PARAMETERS

SET OUT A TIMING N1 8Set the scaled output resolution.

Available values for N1:

0 [Native]

4 [480P60]

6 [720P60]

10 [1080P60]

11 [576P50]

12 [720P50]

16 [1080P24]

17 [1080P25]

19 [1080P30]

416 [1024x768]

417 [1280x800]

419 [1280x1024]

420 [1366x768]

423 [1440x900]

424 [1600x900RB]

425 [1600x1200]

426 [1680x1050]

430 [1920x1200RB]

GET OUT A TIMING 8Show the currently selected output resolution.

GET OUT A TIMING STRING 8Show the currently selected output resolution’s timing description.

SET OUT A AUDIO SOURCE N 8Select the HDMI audio source to send to the output.

N1 = 1 ~ 2 [Input port]

GET OUT A AUDIO SOURCE 8Show the currently selected HDMI audio source.

SET OUT A MUTE N1 8Enable or disable the audio/video output mute function.

Available values for N1:

0 [Off]

1 [On]

GET OUT A MUTE 8Show the current state of the audio/video output mute function.

GET OUT A SYNC STATUS 8Show the current sync state of the HDMI output.

SET IN N1 CONTRAST N2 8Set the contrast value for input N1.

N1 = 1 ~ 2 [Input port]

N2 = 0 ~ 100 [Contrast level]

GET IN N1 CONTRAST 8Show the current contrast value for input N1.

N1 = 1 ~ 2 [Input port]

SET IN N1 BRIGHTNESS N2 8Set the brightness value for input N1.

N1 = 1 ~ 2 [Input port]

N2 = 0 ~ 100 [Brightness level]

GET IN N1 BRIGHTNESS 8Show the current brightness value for input N1.

N1 = 1 ~ 2 [Input port]

SET IN N1 HUE N2 8Set the hue shift for input N1.

N1 = 1 ~ 2 [Input port]

N2 = 0 ~ 100 [Hue]

GET IN N1 HUE 8Show the current hue shift for input N1.

N1 = 1 ~ 2 [Input port]

SET IN N1 SHARPNESS N2 8Set the sharpness value for input N1.

N1 = 1 ~ 2 [Input port]

N2 = 0 ~ 20 [Sharpness level]

GET IN N1 SHARPNESS 8Show the current sharpness value for input N1.

N1 = 1 ~ 2 [Input port]

SET OUT A ASPECT RATIO N1 8Set the output aspect ratio to use in full screen mode.

Available values for N1:

1 [Full]

2 [4:3]

3 [16:9]

4 [16:10]

GET OUT A ASPECT RATIO 8Show the current aspect ratio setting.

ANEUVIDEO

RS-232 & Telnet Commands

RS-232 Commands

COMMAND DESCRIPTION & PARAMETERS

SET IN N1 FORMAT N2 8Force input N1 to use a specic color format.

N1 = 1 ~ 2 [Input port]

Available values for N2:

1 [RGB]

2 [YPbPr 4:2:2]

3 [YPbPr 4:4:4]

GET IN N1 FORMAT 8Show the currently set color space format used by input N1.

N1 = 1 ~ 2 [Input port]

SET IN N1 TEMPERATURE N2 8Set the color temperature to use with input N1.

N1 = 1 ~ 2 [Input port]

Available values for N2:

1 [6500K]

2 [9300K]

GET IN N1 TEMPERATURE 8Show the currently set color temperature used by input N1.

SET IN N1 CHROMA N2 8Set the chroma value for input N1.

N1 = 1 ~ 2 [Input port]

N2 = 0 ~ 100 [Chroma value]

GET IN N1 CHROMA 8Show the current chroma value for input N1.

N1 = 1 ~ 2 [Input port]

SET CHROMAKEY ENABLE N1 8Enable or disable Chromakey mode.

Available values for N1:

0 [Off]

1 [On]

GET CHROMAKEY ENABLE 8Show the current state of the Chromakey mode.

SET CHROMAKEY COLOR N1 8Select the RGB chromakey preset to use when Chromakey mode is enabled.

Available values for N1:

WHITE [White key]

BLACK [Black key]

RED [Red key]

GREEN [Green key]

YELLOW [Yellow key]

BLUE [Blue key]

MAGENTA [Magenta key]

CYAN [Cyan key]

USER [User dened key]

GET CHROMAKEY COLOR 8Show the currently selected RGB chroma preset.

SET CHROMAKEY RED RANGE N1 TO

N2 8

Set the key-out range to use for the red component of the User dened key.

N1= 00 ~ FF [Red min in hex]

N2= 00 ~ FF [Red max in hex]

SET CHROMAKEY GREEN RANGE N1

TO N2 8

Set the key-out range to use for the green component of the User dened key.

N1= 00 ~ FF [Green min in hex]

N2= 00 ~ FF [Green max in hex]

SET CHROMAKEY BLUE RANGE N1

TO N2 8

Set the key-out range to use for the blue component of the User dened key.

N1= 00 ~ FF [Blue min in hex]

N2= 00 ~ FF [Blue max in hex]

ANEUVIDEO

Andere Handbücher für ANI-2PIP-LOGO

Inhaltsverzeichnis

Andere A-Neuvideo Tragbarer Multimedia-Player Handbücher

A-Neuvideo

A-Neuvideo ANI-42HPIP Bedienungsanleitung

Beliebte Tragbarer Multimedia-Player Handbücher anderer Marken

Epson

Epson P3000 - Digital AV Player Abmessungen

VIETA

VIETA VM-HS247BK Bedienungsanleitung

Epson

Epson P6000 - Multimedia Photo Viewer Bedienungsanleitung

Apantac

Apantac Tahoma LE-4 Bedienungsanleitung

Polaroid

Polaroid PMP120-4 Bedienungsanleitung

Creative

Creative ZEN Vision Bedienungsanleitung

Mattel

Mattel Juice Box Bedienungsanleitung

Creative

Creative ZEN Vision Bedienungsanleitung

Denon

Denon HEOS Amp Bedienungsanleitung

Espow

Espow RM Bedienungsanleitung

Philips

Philips HMP3000 Bedienungsanleitung

Archos

Archos 604 - Digital AV Player Bedienungsanleitung

Aigo

Aigo MV5920 Bedienungsanleitung

Yoo Digital

Yoo Digital YOOMOVE 2401 Bedienungsanleitung

Cowon

Cowon iAUDIO CW200 Bedienungsanleitung

Kodak

Kodak mc3 Bedienungsanleitung

Shiro

Shiro VJ Bedienungsanleitung

Philips

Philips GoGear SA3085/02 Bedienungsanleitung