A2Z Drone Delivery RDS1 Bedienungsanleitung

RDS1

USER MANUAL

DISCLAIMER

Please read and understand the contents of this installation and user manual carefully. Failure to read

the manual may lead to personal injury, inferior results or damage to the RDS1 or attached drone.

Always make sure that anyone who uses the RDS1 knows and understand the contents of the manual.

The conditions or methods used for assembling, handling, storage, use or disposal* of the device are beyond our

control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly

disclaim liability for loss, injuries, damage, or expense arising out of or in any way connected with the assembly,

handling, storage, use or disposal of the product.

The RSD1 is designed and built for drone delivery missions and testing within a commercial/business environment.

The mixture of adaptability and easy-integration makes the RDS1 the perfect system for delivering medical supplies,

food, equipment and much more. Although we achieved a very high standard in drone delivery with the RDS1, the user

remains responsible to qualify and validate the application of the RDS1 for its intended use, especially critical for

applications in strictly regulated areas like medical devices. While suitable for most drone platforms, the user will

achieve the best results using an aircraft which has already been integrated by the A2Z Drone Delivery team.

Intended Use of the RDS1

This language version of the manual is verified by the manufacturer (Original manual). No

part of this publication, including pictures may be reproduced and/or made public, whether by

printing, photocopying or by any other means whatsoever, without the prior written

permission of A2Z Drone Delivery.

TABLE OF CONTENTS

Disclaimer

Preface

Warranty Information

Patents

Safety and Compliance

1.1 Important Safety Information

1.2 Operational Limitations

1.3 Hazards

Introduction

2.1 What is Included

2.2 Specifications

2.3 Main Components

Unpacking and Hardware Installation

3.1 Unboxing

3.2 Hardware Installation (M600 Pro)

Software

4.1 Configure DJI Go App

4.2 Activate the M600’s OnboardSDK Support

4.3 Install the A2Z Delivery App

Operation

5.1 Deliver

5.2 Pickup

5.3 Payload Abandon

5.4 Deliver(Abandon Tether)

5.5 Deliver (Reel Down)

5.6 Camera Operation

Maintenance

6.1 Updating Firmware

6.2 Logs

6.3 Spool Calibration

6.4 Scale Calibration

6.5 Replace Tether

6.6 Reinstalling the Tap and Go Hook

Certifications 4

PREFACE

CERTIFICATIONS

This is the installation and user manual for your RDS1 Drone Delivery System. This manual contains chapters about

the installation and use of the hardware and software. The manual contains important information and instructions on

safety, installation and use. Please read all information and follow the instructions and guidelines in this manual

carefully. This ensures that you will have successful drone deliveries and that possible accidents and injuries will be

prevented. Make sure that everyone who uses the RDS1 has access to this manual.

Every effort has been made to make this manual as accurate and complete as possible. The information is believed to

be correct, but does not aim to be all inclusive and shall be used only as a guide. Should you discover any errors or

omissions, please bring this to our attention, so that we can make amendments. This will enable us to improve our

documentation and service to you.

A2Z Drone Delivery has been issued the following patents: US10017353B1, US20210002107A1, CN106945826A,

CN206654621U, CN206691367U, CN110304564B, CN112478165A.

A2Z Drone Delivery has the following patents pending: EP3760541A1

WARRANTY INFORMATION

PATENTS

A2Z Drone Delivery warrants this product against defects in material or workmanship for one year from the date of delivery, or 1,000

cycles — whichever comes first. A2Z Drone Delivery will pay labor and standard freight costs for warranty service for a period of

thirty days from the date of delivery. This warranty does not cover any consumable item (e.g., memory cards, cable). A2Z Drone

Delivery’s sole obligation under said warranty is to repair, or at its option, replace the defective part. All special, incidental, and

consequential damages are excluded.

The warranty shall be voided by alterations of equipment (except by A2Z Drone Delivery), tampering with, improper installation or

maintenance, accident, or misuse. This warranty expressly excludes all damage to these products resulting from careless or

neglectful handling and transportation once it has left the A2Z Drone Delivery’s premises. A2Z Drone Delivery shall in no event be

responsible for any warranty work done without first obtaining A2Z Drone Delivery’s written consent.

This warranty is made expressly in lieu of all other warranties, expressed or implied, including any implied warranties regarding

merchantability or fitness for a particular purpose. No employee, agent, franchise, dealer, or other person is authorized to give any

warranties of any nature on behalf of A2Z Drone Delivery. Except as provided herein, A2Z Drone Delivery shall have no liability or

responsibility to customer or any other person or entity with respect to any liability, loss, or damage caused or alleged to be caused

directly or indirectly by “equipment”.

Notwithstanding the above limitations and warranties, A2Z Drone Delivery’s liability hereunder for damages incurred by customer or

others shall not exceed the amount paid by customer for the particular equipment involved.

For more warranty information, or to contact a technician, visit www.a2zdronedelivery.com.

The RDS1 uses components which have the following certifications:

IP Rating: Not IP rated.

SAFETY AND COMPLIANCE

The RDS1 has moving parts that can cause injury. Never reach into or touch the RDS1 while it is in operation. Always

control the RDS1 manually if on the ground.

Do not change or adjust anything on the RDS1 unless the change is authorized by the manufacturer.

The RDS1 is not intended for use by persons with reduced physical and/or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a

person responsible for their safety.

Children under the age of 16 should not operate the RDS1.

Any modifications made to the RDS1 without the manufacturer’s approval will invalidate the product’s warranty.

1.1 Important Safety Information

Do not deliver payloads heavier than 2kg/4.4lb. Deliver is defined by DROP, DELIVER, REEL-DOWN. Payload

includes the release hook or modified release device.

Do not reel up payloads heavier than 1kg/2.2lb. Reeling up is defined by REEL-UP.

Do not deliver above 45m AGL (Above Ground Level). 45m AGL is the max delivery height. 20-30m is the

recommended delivery height to maintain target accuracy. This height is the relative distance from the drone to the

ground measured by the RDS1’s lidar.

Do not operate in rain or wet conditions. The RDS1’s electronics are not yet IP rated.

Do not operate without prop-strike protection. The RDS1 includes safety wire that is used for protecting against

prop-strikes.

Do not operate in adverse wind conditions. We do not recommend delivering in winds above 8-12mph(gentle breeze).

Inspect tether before each delivery. The area most prone to wear is at the tie-down point where the tether meets the

release hook or release device. If there is any visible fraying, please snip and re-tie.

1.2 Operational Limitations

Electrical Safety

The RDS1 must be used in conjunction with the delivered cables and plugs. In combination, they

guarantee safe use in relation to short-circuit, overload, over-voltage and over-temperature.

Always turn off the drone before doing maintenance or modifications.

Mechanical Safety

The RDS1 contains moving parts. Keep your hands out of the moving mechanisms when ground

testing in order to prevent injury.

Operational Safety

Never operate the RDS1 directly over people. Always follow the drone manufacturer’s operational

procedures when on delivery missions. Make sure to fly in accordance with federal and local laws.

1.3 Hazards

INTRODUCTION

Welcome to the world of drone delivery. This new and exciting technology is the future of package delivery, and the

RDS1 is the most complete and easy to use system available.

The RDS1 is an advanced drone delivery system capable of rapid and accurate delivery from up to 150 feet/45 meters

AGL, carrying payloads up to 5kg. It is extremely easy to install, operate and maintain. A2Z Drone Delivery has

developed this new system from the ground up, and provides an excellent platform to install on most heavy-lift drones

available on the market today.

A2Z Drone delivery thanks you for purchasing your new delivery system and promises to be valuable resource when

setting up your new RDS1. Please feel free to reach out to us for any reason.

The RDS1 comes with the following components:

Additional Required Items(for use with DJI M600 Pro):

2.1 What is Included

2.2 Specifications

Item Quantity Package Label

A2Z RDS1 A

A2Z RDS1 Tap & Go Boxes

DJI A3 Pro to Pi Zero Cable

Kevlar Tether

XT30 Cable

A2Z RDS1 Lidar

M600 Pro Landing Bar Safety Wire

A2Z RDS1 Tap N Go (extra)

M600 Pro Rail Spacers

A2Z RDS1 Debugger Wire

A2Z RDS1 Firmware Upgrade Adapter

1A2Z RDS1 Tap & Go Knot-Tying Tool

1A2Z RDS1 PCB to Pi Zero Cable

• Android Tablet

• DJI X3/X5S/Z3 Camera

• DJI M600 Pro Gimbal Mounting Kit

Max delivery payload capacity: 2 (kg) / 4.4 (lbs)

System dimensions: 35L x 18W x 27H (cm)

System weight: 1-1.5 kg (dependent on choice of motor)

Max delivery height (AGL): 150 (ft) / 45.27 (m)

Decibels at max delivery height with DJI M600 Pro: <60 (dB)

Delivery accuracy from 20m AGL: <2 (m) radius (stable wind)

Time-to-ground from max delivery height: 4 (s) (1kg payload)

Reel-up payload capacity: 300-1,000 (g) (dependent on choice of motor)

Reel-up speed: 0.5-4 (m/s) (dependent on choice of motor)

Max delivery range with DJI M600 Pro: 3.5 (km) / 2.17 (miles)

A2Z box dimensions (customizable): 20Lx14Wx8H (cm)

The components of the RDS1 are as follows:

2.3 Main Components

Servo

Pi Zero Board

RDS1 Main Control Board

RDS1 Floating Universal Mount

Cable Spool

DC Motor

Tap N Go

Proximity Sensor

Encoder

Break

Winding Gear

Different Views of the RDS1.

2.3 Main Components

12 13

12 Lock Release Button

13 Manual Wind/Lock Button

Rear View

Side View

Bottom View

UNPACKING AND HARDWARE INSTALLATION

Open the main box containing the RDS1. Unwrap all of the components and lay everything out. Be careful when

opening and do not use sharp objects to cut through the wrapping, as they may cause scratches or damage parts.

3.1 Unboxing

3.2 Hardware Installation (M600 Pro)

1. Locate the top of the M600 Pro, and with a 2.5mm hex driver, remove the 4 screws. Remove the 2 screws

holding on the front GPS unit and mount. Remove the top cover. Be careful, as the fan wire will be attached.

Place the cover/front GPS to the side on the frame, just so it is out of the way of the A3 unit.

3. From under the main frame of the M600 Pro, slightly pull down the front of the bottom plastic cover in order to

easily access the frame opening. Take the side of the A3 Pro API Port Cable with the black and white wires

located on the outside of the plug and push it up through the opening. IT IS EXTREMELY IMPORTANT TO PUSH

THE CORRECT SIDE OF THE A3 PRO API PORT CABLE UP THROUGH THE FRAME.

4. Looking from the top of the airframe, use a pair of tweezers to grab the end of the A3 Pro API Port Cable and

pull it up through the top frame plate. Be careful not to damage the other wires. This may be tricky and it may take

a few tries.

2. Remove the gimbal mounting kit and any gimbals/sensors from the M600 Pro.

UNPACKING AND HARDWARE INSTALLATION

Inhaltsverzeichnis

Andere A2Z Drone Delivery Drohnen- und Quadcopter-Zubehör Handbücher

A2Z Drone Delivery

A2Z Drone Delivery RDS2 Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken

ParaZero

ParaZero SafeAir Mavic Bedienungsanleitung

JT SS125 Bedienungsanleitung

dji

dji Zenmuse X9 Bedienungsanleitung

dji

dji Goggles Bedienungsanleitung

dji

dji E7000 Bedienungsanleitung

RunCam

RunCam Phoenix HD Bedienungsanleitung

DRS

DRS DRS-M210-V2 Bedienungsanleitung

Kogan

Kogan 4K GALAXY Bedienungsanleitung

Opale Parachutes

Opale Parachutes SAFETECH 3.2K ST60 Bedienungsanleitung

Flycolor

Flycolor X-Cross Mini 4in1 Bedienungsanleitung

ParaZero

ParaZero SafeAir Phantom Bedienungsanleitung

dji

dji PHANTOM 2 VISION PLUS Bedienungsanleitung

HOBBYEAGLE

HOBBYEAGLE A3 Mini Bedienungsanleitung

TCMM RC

TCMM RC AC 220 Bedienungsanleitung

iKarus

iKarus Profi Gyro Bedienungsanleitung

R2TECK

R2TECK NEXG1 Bedienungsanleitung

Hesai

Hesai Pandar40P Bedienungsanleitung

Flycolor

Flycolor X-Cross HV 2 Series Bedienungsanleitung