Dji PHANTOM 2 VISION PLUS Bedienungsanleitung

5Preparing the Remote Controller

The PHANTOM 2 VISION+ remote controlleris a wireless communication device that uses the 5.8GHz frequency

band. The link between the remote controller and aircraft isalready established before delivery.

The remote controller default is set to Mode 2 and CE compliance before de l iv e r y. Both the operating mode and

compliance version can be configuredin PHANTOM RC Assistant Software. Please referto <PHANTOM

RCAssistant> and <ComplianceConfiguration> for details.

Compliance Version: The PHANTOM 2 VISION+ remote controlleris compliant with CE and FCC (see the

FCC ID) regulations.

Operating Mode

: The remote controller is d iv i de d to Mode 1 and Mode 2 according to different channel

mappings.

Mode 1

: The left stick is mapped to throttle channel.

M ode 2 : The right stick is mapped to throttle channel.

The range extender and mobile device holder is already mounted on the remote controller. Twist mobile

device holder to face outwards and fix in position to prepare for mobile device installation.

It is recommended not to use oversized mobile devices (e.g. iPad), which cannot be placed into the

Mobile Device Holder.

5.1The Remote Controller

[1]

[2]

[4] [3]

[8]

[9] [11]

J4 [6]

[7]

[5]

[10]

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

Antenna

Carrying Handle

SwitchS1

Switch S2 (Reserved)

Joystick(J1: Roll [left&right], J2: Pitch [front&back])

Joystick(J3: Throttle [up&down], J4: Yaw [rotation])

Neck Strap Attachment

Power Switch

Power Indicator

RC Assistant Port(Micro-USB Port)

Battery Compartment (On the back)

5.2 Power on the Remote Controller

Install the four AA Batteries into the battery compartment on the back of the remote controller

according to the negative andpositive p o le s .

Set the S1 and S2 switches to the upper most position and all sticks at mid-point.

Toggle the power switch to right end to switch on the power.

4. There is a power on indicator beep. If the remote controller is set to be CE compliant, then there will be

one beep while the FCCcompliant version will emit 2 beeps. The power indicator blinks greenquickly

indicating the remote controller and receiver are binding. Once binding is completed, the power

indicator will change to a solid green.

（

）

If the low voltage warning alert sounds(refer to the <Remote Controller Power Indicator Status

Information>), please replace batteries as soon as possible.

（2）For long term storage, be sure to remove the batteries from the remote controller.

（

）

Dispose the depleted batteries safely.

5.3 Remote Controller Power Indicator Status Information

Power indicator

Sound

Remote Controller State

None

Functioning normally.

None

Establishing a link between the remote controller and the receiver.

B-B-B……

Low voltage (at 3.9V-4.5V), should replace the batteries immediately.

BBBB

Low voltage (lower than 3.9V). The remote controller will automatically

power off. Replace the batteries immediately.

B-B-B……

The remote controllerwill give a visual indication of an alarm after 15

minutesof non-operation. The alarm status will go awayonce you start

operating of the remote controller.

The remote controllerwill blink the LED and sound an alert when the voltage drops below3.9V and

automatically power off after 3 seconds. This process will repeat even if you power cycle the remote

controller. If this low voltage warning occurs during flight, the remote controllerwill automatically

power off causing the aircraft to enter Failsafe mode which cannot be interrupted (refer to <Failsafe

Function> section for details). It is strongly recommended to replace batteries immediatelyif the low

voltage warning(3.9V-4.5V) occurs.

5.4 AntennaOrientation

Try to keep the antenna pointingskyward, perpendicular to the ground, in order to achieve the maximum

communication range during flight.

The rem ote controller’s

antenna should be pointing

skyw ard w ith no obstacles in

the w ay. O therw ise,the

F a ils a fe fu n c tio n m a y in it ia liz e

prem aturely during flight.

The M obile D evice and Range

Extendershould notblock

the antenna.

5.5 Remote Controller Operation

The remote controller default is set to Mode 2 before delivery, follow descriptions takes Mode 2 for example.

Stick Neutral/ mid point:Control sticks of theremote controller are placedatthe central position.

Move the Stick:The stick of remote controller is pushed away from the central position.

Remote Co n tr o l le r

(Mode 2 )

Aircraft

（

nose direction

）

Operation de ta i ls

The throttle stickcontrolsthe aircraft elevation.

Push the stickup and the aircraft will ascend.

Pullthe stickdown and the aircraft will descend.

The aircraft will automatically hover and hold i ts

height when bothsticksare centered.

Push the throttle stickupward beyondthe centered

(neutral) position to take off the aircraft. We suggest

that you push the throttle stickgently to prevent the

aircraft from sudden and unexpectedelevation.

The yaw stickcontrols the ai r c r a f t r u dde r.

Push the stickleft and the aircraft will rota te counter

clock-wise.

Push the stickright and the aircraft willro tate

clock-wise.If the stick is centered, the aircraft will

always fly in the same direction.

The command stick controls the rotating angular

velocity of the aircraft. Increasing movement of the

command stick results in fasteraircraft rotation

v e lo c i ty.

The pitchstickcontrols the aircraft’sfront & back

pitch.

Push the stick up and the aircraft willpitchand fly

forward.

Pullthe stickdown and the aircraft willpitchand

flybackward.The aircraft will k e e p le ve l and straight

if the stick is centered.

Increasing movement of the command stick will

result in a largerpitch angle (maximum is 35˚) and

faster flight velocity.

The rollstick controls the aircraft le f t &rightpitch.

Push the stickleft and the aircraft will pitchand fly

le f t .Pushthe stick right and the aircraft willpitch and

flyright.The aircraft will keep level and straight if the

stick is centered.

Increasing movement of the command stick will

result in a largerpitch angle (maximum is 35˚) and

faster flight velocity.

Position-1 Position-2 Position-3

S1 is for compass calibration. Toggle the S1 from

position-1 to position-3 and back to position-1

about 6 to 10 times which will force the aircraft to

enter into compass calibration mode.

In Naza-M mode, the S1 switch is used to switch

control mode and compass calibration.

Position-1 Position-2 Position-3

S2 is used to record Home point manually. After a

Home point is automatically recorded, quickly

flipping the S2 switch of the remote controller from

upper most to lower most positions 5 times or more

will reset the current aircraft position as a new

home point of PHANTOM 2 VISION+.

InNaza-M m o de , S2 is involved in IOC function.

(1)

For ‘Ready to Fly’ the aircraft will hover (hold a stable horizontal position) when all sticks are

released.

(2)

For ‘Ready to Fly (non-GPS)’ the aircraft will keep the aircraft level without horizontal

positioning when all sticks are released.

5.6 Link between the Remote Controller and Receiver

A5.8G receiver is built-in PHANTOM 2 VISION+, i ts link button and indicator lo c a t e do n the bottom of the aircraft as

illustrated in the following diagram.

The link between the remote controller andreceiver isalready established before delivery. Only re-establish the link

when you try to replace the old remote controller or receiver with a new one.

L in k B u tto n &

L in k In d ic a to r

Link Procedures

Power off the remote controller, power on the aircraft.You will see the link indicator blinking red.

Press the linkbutton with a thin object and hold until the link indicator blinks yellow.Release the

linkbutton.

Power on the remote controller and the link indicator shouldswitch off. This indicates that the link has

been successfully established.

Link Indicator

Description

Next Operation

No signal received.

Switch on the remote controller or perform a link procedure.

In link status.

Switch on the remote controller.

5.7 Compliance Version Configuration

The compliance version can be reconfigured by twisting the potentiometer knob (See the following diagram) on

the back of the remote controller using a flathead screwdriver. For CE compliance, set the remote controller to CE

compliance by carefullyturning the potentiometer knob to the full counter clock-wise position.For FCC compliance,

set the remote controllerto FCC compliance by carefully turning the potentiometer knob to the full clock-wise

position. Users should follow their lo c a l regulations accordingly.

FCCCE

（

）

When adjusting the potentiometer knob to its limit position, be very careful to prevent

damaging the potentiometer knob. Do not apply too much force during this adjustment. Also be

sure to use the correct sized screwdriver.

（2）CE compliant devices have an effective communication range of 300 meters in open spaces due

to power limitations. Be sure to watch your fight distance as the PHANTOM 2 VISION+will

enter Failsafe mode (auto-landing or go home and land) if it fliesbeyond this range.

（3）FCC compliant devices have an effective range of 500 meters in open spaces. Be sure to watch

your fight distance as the PHANTOM 2 VISION+will enter Failsafe mode (auto-landing or go

home and land) if it fliesbeyond this range.

（

）

Pay attention to and follow local laws and regulations.

（

）

The remote controller comes set for CE compliance up delivery as the default setting.

（2）It is recommended to use a flathead screwdriver of Φ2.4mm for adjustment.

（

）

There is another potentiometer reserved.

6Preparing the Range Extender

The PHANTOM 2 VISION+ range extender is a wireless communication device that operates within the 2.4 GHz

frequency band and is used for extending the effective range of communication between a mobile device

(Smartphone) and the PHANTOM 2 VISION+. In an open unobstructed area, the transmission distance can reach

up to 500 meters, but is usually affected by the surrounding environment, such as trees, buildings and other

sources of the same frequency. Before every flight, it is suggested that you ensure the range extender functions

properly. Otherwise you may experience a communication issue with the mobile device and the PHANTOM 2

VISION+.

Each range extender has a unique MAC address and network name (SSID), details of which are printed on the label

as ‘Phantom_XXXXXX’. The ‘XXXXXX’ represents the last 6 letters or numbers of the MAC address for the range

extender, users can rename the “XXXXXX” part in DJI VISION App.

6.1 The Range Extender

[1]

[2]

[3]

[7]

[6]

[5]

[4]

Front View Right View

[1]

[2]

[3]

[4]

[5]

[6]

[7]

SYSTEM Indicator

POWER Indicator

Lock-screw

Reset Button

Power Switch

Charging Port(Micro-USB port)

Mounting Bracket

SYSTEM Indicator

Tells you the Wi-Fistatus of range extender.

SYSTEM Indicator

Description

The Wi-Finetwork is functioning normally.

Off

The Wi-Fi network is functioning abnormally.

Power Indicator (POWER)

Tells you the power status of range extender.

POWER Indicator

Description

The range extender is working normally or completely charged.

Low voltage alert, a re-charge is required.

The range extender is charging

If the power indicator is a solid red light, the ranger extender may stop working at any

moment.Recharge it as soon as possible.

Reset Button

Every time press the reset button once will reset the range extender, and the range extender will restart. Users

have to bind the range extender with a PHANTOM 2 VISON+ again to rebuild a Wi-Fi network; otherwise the DJI

VISION App will be failed to connect.

6.2 Usage

Charging the Range Extender

Charging the range extender by connecting the charging port of it to a power supply device (such as PC and

Micro-USB charger) via a Micro-USB cable. Make sure to charge the range extender completely before using it

for the first time. It takes 3~4 hours (depending on USB power output) to be fully charged.

Make sure the range extender has enough power battery before each use.

Powering on the Range Extender

Toggle the power switch of range extender to ON position.

2. Wait for approximately 30 seconds. The Wi-Fi signal indicator should blink green indicatingthe range

extender is communicating properly.

Keep the range extender facing the aircraft during flight for the best communication link.

It is advised that you power off the range extender after every flight to avoid discharging the battery.

Battery capacity level display

In the main page of DJI VISION App, a progress bar will display the battery capacity level and SSID of current

connecting range extender. The percentage of the progress indicates the percentage of current capacity level. The

progress bar is green when the percentage is no less than 30%, and it’s red when the percentage is less than

30%.When the progress bar turns red, please charge the range extender as soon as possible.

Low battery capacity warning

During flight, when the range extender is low battery capacity, a warning will appear in the camera page of DJI

VISION App.

6.3Rename SSID of Range Extender

For easier acknowledge the SSID of your range extender, users can rename SSID of range extender.

Tap “Rename SSID of Range Extender” in the Settings page. Enter a new name SSID name (e.g. Phantom_2

VISION+) in the textbox.

2. Tap

,and users will be asked to enter the last six numbers of MAC address on range extender to confirm

the modification.

3. Tap“OK” to confirm and the range extendershould automatically restart. Approximately 30 seconds later,

the network named of Phantom_2 VISION PLUS can be searched in theWi-Fi list of your mobile device.

Select and connect the renamed network, DJI VISION App can be used.

6.4 Binding theCamera &Range Extender

If the connection of PHANTOM 2 VISION+ and range extender is lost, or one of them needs to be repaired or

replaced, a camera and range extender binding will need to be performed via the DJI VISIONApp.

Reset

B u tto n

Power on the camera and range extender.

2. Approximately 30 seconds later, press the resetbutton on the range extender with a thin object until the

SYSTEM Indicator turn off.The range extenderwill then restart automatically.

3. Approximately 30 seconds later, the SYSTEM Indicator should start to blink green, which indicates the

range extender is now ready to be bound.

4. (Fig.1)Run the DJI VISION App->Settings->General->Binding. (Fig.2) Select’Scan the QR Code’ to scan the

camera QR c o de on the product packaging. (Fig.3) Get the camera SSID (E.g. FC200_0xxxxx) and the MAC

address. Users can also skip the scan and enter the camera MAC address directly (Fig.4, Fig.5), the MAC

address can be found on the label on camera.

5. Select the tickon the top right corner. The range extendershould automatically restart. The binding

procedure is now c o m p le t e d.

二维码

示例

DO NOT push the reset button of the range extender unless you are ready to rebind the range

extender and the camera! This will unbind your camera and you must follow the steps above to

rebind.

If both the PHANTOM 2 VISION+ aircraft and range extender are powered on and working normally,

you will be able to find the SSID on the Wi-Fi list of the mobile device.

（

）

The QR code is located on the packaging of the PHANTOM 2 VISION+. If you cannot find the QR

Inhaltsverzeichnis

Andere dji Drohnen- und Quadcopter-Zubehör Handbücher

dji

dji FC7BMC Bedienungsanleitung

dji

dji SNAIL 2305 Bedienungsanleitung

dji

dji E7000 Bedienungsanleitung

dji

dji Osmo Z-Axis Bedienungsanleitung

dji

dji ACTION 2 Bedienungsanleitung

dji

dji E-Port Development Lit Bedienungsanleitung

dji

dji MG Bedienungsanleitung

dji

dji Inspire 1 1345LS Bedienungsanleitung

dji

dji Aeroscope AS-F1800 Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji RC 2 Bedienungsanleitung

dji

dji DL LENS Bedienungsanleitung

dji

dji RD2412R Bedienungsanleitung

dji

dji Dropsafe Bedienungsanleitung

dji

dji ZENMUSE L1 Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji Snail 6048-3D Bedienungsanleitung

dji

dji Snail Bedienungsanleitung

dji

dji MATRICE 300 RTK Bedienungsanleitung

dji

dji Smart Controller Enterprise Bedienungsanleitung

dji

dji Aeroscope upgrade module Bedienungsanleitung

dji

dji Aeroscope Mobile Bedienungsanleitung

dji

dji ZENMUSE XT S Bedienungsanleitung

dji

dji Ronin Series Battery Power Distributor Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken

A2Z Drone Delivery

A2Z Drone Delivery RDS2 Bedienungsanleitung

ParaZero

ParaZero SafeAir Mavic Bedienungsanleitung

JT SS125 Bedienungsanleitung

RunCam

RunCam Phoenix HD Bedienungsanleitung

DRS

DRS DRS-M210-V2 Bedienungsanleitung

Kogan

Kogan 4K GALAXY Bedienungsanleitung

Opale Parachutes

Opale Parachutes SAFETECH 3.2K ST60 Bedienungsanleitung

Flycolor

Flycolor X-Cross Mini 4in1 Bedienungsanleitung

ParaZero

ParaZero SafeAir Phantom Bedienungsanleitung

HOBBYEAGLE

HOBBYEAGLE A3 Mini Bedienungsanleitung

TCMM RC

TCMM RC AC 220 Bedienungsanleitung

iKarus

iKarus Profi Gyro Bedienungsanleitung

R2TECK

R2TECK NEXG1 Bedienungsanleitung

Hesai

Hesai Pandar40P Bedienungsanleitung

Flycolor

Flycolor X-Cross HV 2 Series Bedienungsanleitung

CZZN

CZZN GL60 ZOOM Bedienungsanleitung

PowerVision

PowerVision PowerEgg Bedienungsanleitung

A2Z Drone Delivery

A2Z Drone Delivery RDS1 Bedienungsanleitung

dji PHANTOM 2 VISION PLUS Bedienungsanleitung

Beliebte Drohnen- und Quadcopter-Zubehör Handbücher anderer Marken