Aaeon PCM-6893 Bedienungsanleitung

TB192 (Rev1) - Installing An Aaeon PCM-6893 In An M15

Overview

This document describes the procedure for installing the Aaeon PCM-6893 motherboard in an M15-6 Clr, or newer, color

console. This motherboard is a replacement in systems that have an industrial motherboard and an NEC 10.4” LCD

screen. If you have an NEC 9.4” Color LCD screen, you will need a different LCD cable. Below you will find a list of all

the components that you should have received with the Aaeon motherboard.

* Aaeon PCM-6893 Motherboard, complete with CPU and memory

* Heat sink, fan w/ mounting bracket, and 2 nylon spacers (.244”)

* LCD Cable

* ATX Power Supply

* Aaeon Hard Drive cable and Floppy cable

* Aaeon Keyboard and mouse cables

* Serial and Parallel cables

* Ethernet Cable

* Drive/inverter power cable

* Fan/probe power cable

* Misc. power extension cables

* USB cable with 1 USB extension

Installation

The first step in the installation process is to remove all of the old components. You must remove the old motherboard

assembly, complete with CPU, memory and heatsink. You must also remove the old LCD descrambler card and LCD

cable. You will no longer need the existing Ethernet cable, keyboard/mouse cable, or hard drive cable and floppy cable.

If the power supply is not of the ATX type or is a Morex PS, then you will need to remove it as well. This document

contains the recommended installation procedure. Follow it exactly to avoid any problems. If there is any confusion,

please refer to picture 3 of an Aaeon motherboard with cables connected.

1. Before installing the Aaeon motherboard, put a piece of 2-sided foam tape on the bottom of the fan bracket to avoid

unwanted vibration. The fan bracket will need the mounting holes drilled out to ¼” to fit over standoffs. Now place the fan

bracket assembly over top of the front standoffs. Install the nylon spacers over the standoffs, on top of the bracket. When

you install the motherboard the bracket will now be held in place. (See picture 1)

Picture 1: Cooling fan and bracket mounted in M15 console

2. Install the Aaeon motherboard on the existing motherboard standoffs at the bottom of the case. Refer to Picture 2 for

orientation.

3. Attach the new LCD Cable to CN3 on the motherboard and the other end to the LCD screen using the existing screws,

standoffs, and LCD Cable Mounting Bracket. The cable is keyed so, it can only be plugged in one way. The mounting

bracket goes over the LCD Connector to hold in place on the LCD.

4. Attach the Hard Drive cable to IDE1 on the motherboard. The red stripe goes to Pin 1, which is towards the CPU

Socket.

5. Attach the floppy drive cable to FDC1 on the motherboard (pin one closest to the standoff).

6. Attach the serial cable to CN6 on the motherboard. This socket is keyed and can only go on one way.

7. Attach the LPT1 cable to LPT1 on the motherboard. This socket is keyed and can only go one way.

8. Attach the USB cable to USB2 on the motherboard. Pin 1 is labeled with an Arrow and is the Red wire on the USB

Cable.

9. Connect new Ethernet cable to LAN1 on the motherboard.

10. Plug ATX power connector into PWR1. It will only plug in one way.

11. Connect the new keyboard/mouse cable to CN7. It will only connect one way.

12. After all cables are installed you will carefully need to route all the cables so that they do not obstruct the CPU7. The

LCD cable can be routed around the RAM as shown in Picture 2. Extra care must be taken with the ATX power

connector so that is does not interfere with the bottom of the CPU7 card.

13. If the M15 was not fitted with an ATX style power supply, then you will have to drill new mounting holes for the new

ATX power supply. Mount the ATX power supply as shown in Picture 1 above. Use the angled bracket and the pre-

existing bracket on the power supply to secure it to the console.

14. Power up console to verify MB will boot. You may need to go into the CMOS setup to change some settings. To do

this, hit the DEL key on the keyboard when the control does the Memory check. Go into STANDARD CMOS SETUP.

Change the Screen Resolution to 640x480 TT1. You must change the HALT option to ALL, BUT KEYBOARD. Go in to

the Power Management Setup and change PWRON after PWR-Fail to ON.

Note: If the motherboard was not setup at Centroid you may need to momentarily jumper pins 1 & 2 on CN9 while power

is applied to the motherboard. The motherboard will turn on and allow you to enter the BIOS. You must change the

power management as described above. Remove power before continuing with next step.

Picture 2: Aaeon motherboard installed in an M15

15. Re-install the CPU7; you may need to use 1/16” spacer on the top and bottom of each standoff. Ensure that the

CPU7 is inserted all the way into the socket. Also be sure that the CPU7 will line up correctly with the back panel.

16. Temporarily connect IDE and floppy cables to sshdd and floppy drive. Power up again to verify system boots up into

CNC10 software. If ok then power down and continue to reassemble M15. If it doesn’t boot into the cnc10 software, see

the notes below for troubleshooting. Note: If using the flash card reader supplied by Centroid, verify JP4 has the two pins

closest to the IDE connector jumpered.

Picture 3: Aaeon with cables inserted correctly

Notes:

* Be very careful with the routing of the cables. The pictures above show our recommended cable routing.

* You must ensure the CPU7 board is pressed fully down into the socket on the motherboard; failure to do so will cause a

64180 Timeout not responding error message when loading CNC7.

* Check the clearance between the Motherboard and the CPU7. Ensure none of the cables are pinched by the CPU7.

You may need to trim the ATX power connector to allow the wires to fold down either side as shown in the picture above.

Jumpers and Connectors

Doc ment History

Rev1 Created on 2006-11-22 by #300

Andere Handbücher für PCM-6893

Inhaltsverzeichnis

Andere Aaeon Hauptplatine Handbücher

Aaeon

Aaeon PCM-5894 Bedienungsanleitung

Aaeon

Aaeon IMBA-Q77 Bedienungsanleitung

Aaeon

Aaeon GENE-BT04 Bedienungsanleitung

Aaeon

Aaeon PCM-7890 Bedienungsanleitung

Aaeon

Aaeon EMB-900M Bedienungsanleitung

Aaeon

Aaeon SBC-557 Bedienungsanleitung

Aaeon

Aaeon MB-662 Bedienungsanleitung

Aaeon

Aaeon ?COM-BT Bedienungsanleitung

Aaeon

Aaeon GENE-A55E Bedienungsanleitung

Aaeon

Aaeon EMB-LN9T Rev.B Bedienungsanleitung

Aaeon

Aaeon PCM-6890 Bedienungsanleitung

Aaeon

Aaeon PICO-EHL4 Bedienungsanleitung

Aaeon

Aaeon SBC-659 Bedienungsanleitung

Aaeon

Aaeon IMBA-Q77 Bedienungsanleitung

Aaeon

Aaeon MAX-H310A Bedienungsanleitung

Aaeon

Aaeon PICO-BT01 Bedienungsanleitung

Aaeon

Aaeon XTX-U15B Bedienungsanleitung

Aaeon

Aaeon PCM-6890 Bedienungsanleitung

Aaeon

Aaeon EMB-CV1 series Bedienungsanleitung

Aaeon

Aaeon SBC-558 Bedienungsanleitung

Aaeon

Aaeon FSB-B75H Bedienungsanleitung

Aaeon

Aaeon IMBM-H81B Bedienungsanleitung

Aaeon

Aaeon GENE-9655 Bedienungsanleitung

Aaeon

Aaeon FSB-H81H Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung