A&D UC-350BLE Bedienungsanleitung
E-1
Instruction Manual
Safety Information E-2
Overview E-4
Initial Start-Up E-6
Start Measuring E-9
Manage Your Health E-11
Troubleshooting E-12
Specications E-14
Maintenance E-15
Warranty E-15
UC-350BLE
DELUXE CONNECTED
WEIGHT SCALE
Thank you very much for selecting the A&D Medical Deluxe Connected Weight
Scale UC-350BLE. Please do read the user manual carefully and thoroughly so
as to ensure the safe usage of this product, and keep the manual well for further
reference in case you have problems.
E-2
Safety Information
Symbol Meaning
The warning signs and symbols are essential to ensure your correct and safe use of
this product and protect you and others from injury. Please kindly nd the meanings
of the warning signs and symbols, which you may encounter in the label and user
manual, as follows:
Symbol Description
Manufacturer
Direct Current
Serial Number
Complies with EU Requirements
Environment Protection – Waste electrical products should not be
disposed of with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for recycling advice
E-3
Your Scale and Its Environment
To ensure your safety as well as the service life of your scale, please avoid
using the scale under the following circumstances:
• Slippery oor such as tile oor
• Jumping onto the platform immediately after bath or with wet hands
• Near a cell phone or microwave oven
Avoid storage in the following locations:
• Where there is water
• Where the device may be exposed to extreme temperatures, humidity, moisture,
direct sunlight, dust, or salt air
• Where there is risk of shock or drop
• Where you store chemicals or full of corrosive gases
• Where in reach of the infants or children
Efcient Use of Your Scale
To ensure the accuracy of measurement, please follow below instructions
when you start measurement.
• Place the scale on a at, hard surface. Soft surface such as carpet will affect the
performance of the scale.
• Avoid measurement immediately after strenuous exercise, sauna or bath,
drinking, and dinning.
• Always start measurement in the same time slot and on the same scale located
on the same at, hard surface.
E-4
Overview
Device Components
Includes:
• Glass Body Scale GBS-1270-B
• 4 x AAA Batteries (1.5V each)
• User Manual
LCD Display
LCD display
DOWN Button
SET Button
UP Button
UNIT and activation
Button Sensor
Battery Compartment
Pound
Kilogram
Successful Bluetooth Connection
Data transmitting/pending to transmit
to wireless wellness system
Low Battery
E-5
Initial Start-Up
Insert the Batteries
• Open the battery door in the back of the scale.
• Insert the batteries (4 x 1.5V AAA) into the battery
compartment according to the polarity indications
marked inside the compartment.
* The digits “ ” will be shown on the LCD.
• Close the battery door and wait until the digits “ ”
are shown on the LCD.
CAUTION
• When the symbol appears, the device will power off. Then you shall
replace with a new set of batteries. Please replace all four batteries at the
same time. Do NOT mix the old batteries with the new one.
• Worn batteries are hazardous waste. Do NOT dispose of them together with
the household garbage. Please refer to the local ordinances and recycling
instructions regarding disposal of the worn batteries and scrapped device.
• If you do not intend to use this unit for a prolonged period of time, it is
advisable to remove the batteries before storing.
E-6
Pair-Up
With the advanced Bluetooth 4.0 technology applied, the mobile or portable
equipments, which are equipped with Bluetooth function in line with BLE Technical
Specications established by global organization Bluetooth SIG, are capable to
receive your personal health data.
• Turn on Bluetooth and the App. Make sure both are ON when pair-up is
proceeding.
• Press and hold “UNIT” button in the back of the scale to start pair-up.
Symbol and symbol will
be shown on the LCD alternatively,
indicating pair-up is proceeding.
If SUCCEED, symbol will be
shown on the LCD.
If FAIL, symbol “E1” will be shown
on the LCD.
E-7
Select Measurement Unit
With batteries correctly installed, press “UNIT” button in the back of the scale to
select measurement unit. The default measurement unit is “lb”. You may press
“UNIT” button to choose among kilogram and pound.
CAUTION
• Please put the scale on at hard ground when nishing the unit selection.
Wait for a few seconds, then you may start measuring according to the
measuring procedure below. If there is not any operation in weighing mode,
the scale will turn off in a few seconds.
Initialising Your Scale
1. Press the platform centre and remove your foot.
2. “0.0” will be displayed.
3. The scale will switch off and is now ready for use. This initialisation process must
be repeated if the scale is moved. At all other times step straight on the scale.
E-8
Start Measuring
Weight Only Operation
Your TRANSTEK Body Scale will operate as a conventional weight – reading
scale. No special programming steps are required.
Once the scale is initialized, as previously described, you may simply step on the
scale to measure your current weight. For only weight reading.
1. Position the scale on a at, hard surface. Carpeted or uneven oors may affect
accuracy.
2. Step onto the scale platform and remain still while the scale computes your
weight.
3. Step off and the scale will display your weight value.
4. The scale will automatically turn off after a few seconds.
Note: The weight value won’t be saved in the scale, and won’t be transmitted to the APP.
Setting the User ID and Start Measuring
Assigning User ID
• With batteries correctly installed, press “SET” button to enter setting. Or when
the LCD displays 0.0, press and hold “SET” button for about 3s to enter setting
mode.
• As pictured below,“P1” blinks. The operator may press the function button or
to select User ID among P1 to P8.
• Press “SET” button to conrm User ID.
E-9
• After setting the personal information, step on the platform when the scale
displays “0.0”.
• Stand still and keep full contact with the scale until the unit stop ashing, then
the weight is locked.
• When your scale is successfully paired with your smartphone and the Bluetooth
is ON, it will process data transmission automatically. (Please refer to Data
Transmission for more details.)
E-10
Manage Your Health
Data Transmission
• Once the Body Scale GBS-1270-B is successfully
paired-up with your smartphone, please open the
“TransHealth” App and turn on your Bluetooth. Keep
smartphone and scale in transmission distance.
Step on the scale and take a measurement. Once
the measurement is nished the data is automatically
transferred to the app.
• The symbol will disappear after
successful data transmission,
and you may check your personal
health data stored in your
smartphone.
• If the data transmission fails,
the symbol will remain. The
pending measurement data will
be temporarily kept in the scale
and transmitted to your smartphone
when next measurement is
complete.
Note: Whether the data transmission is successful, the device will shut down automatically 3 seconds later.
Data transmitting
Data ready to transmit to
the App:
• If SUCCEED, the symbol
disappears;
• If FAIL, the symbol remains.
Inhaltsverzeichnis
Andere A&D Skala Handbücher
A&D
A&D HL-4000 Bedienungsanleitung
A&D
A&D GF-30K Bedienungsanleitung
A&D
A&D HW-10KGL Bedienungsanleitung
A&D
A&D PV-60 Bedienungsanleitung
A&D
A&D AD-4212C-300 Bedienungsanleitung
A&D
A&D GR-120 Bedienungsanleitung
A&D
A&D BM-20 Bedienungsanleitung
A&D
A&D SJ-1000H Bedienungsanleitung
A&D
A&D HW-D Bedienungsanleitung
A&D
A&D GX-L Series Bedienungsanleitung
A&D
A&D BA Series Bedienungsanleitung
A&D
A&D UC-324THW Bedienungsanleitung
A&D
A&D FZ-i Series Bedienungsanleitung
A&D
A&D EK-AEP Series Bedienungsanleitung
A&D
A&D FZ-300CT Bedienungsanleitung
A&D
A&D HT-300 Bedienungsanleitung
A&D
A&D UC-321PL Gebrauchs- und Pflegehandbuch
A&D
A&D GX-M Series Bedienungsanleitung
A&D
A&D HC-30Ki Bedienungsanleitung
A&D
A&D UC-351PBT-Ci Bedienungsanleitung
