ABB FCAN-01 Installationshandbuch

Safety instructions

WARNING! Obey the safety instructions of the drive. If you ignore them, injury or death, or

damage to the equipment can occur.

Mechanical installation

Electrical installation

Layout of the module

1. Pull out the lock.

2. Install the module carefully to an option

module slot of the drive. See the drive

hardware manual.

3. Push in the lock.

4. Tighten the screw to torque 0.8 N·m

using a Torx TX10 screwdriver.

WARNING! Do not use excessive force, or leave the screw too loose. Over-tightening can

damage the screw or module. A loose screw decreases the EMC performance, and can

cause an operation failure.

No. Description

1Lock

2 Mounting and grounding screw

3 Bus connector [X1]

4 Diagnostic LEDs

—

OPTIONS FOR ABB DRIVES

FCAN-01 CANopen adapter module

Quick installation and start-up guide

Start-up

To control the drive with the adapter module, set at least the basic parameters listed in the table

below. For full parameter descriptions, refer to the adapter module’s user manual or to the drive’s

firmware manual.

Basic parameter settings

To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par

refresh.

Further information

Pin allocation for [X1] Bus termination

Bus termination is required to prevent signal reflections from

the bus cable ends. The module is not equipped with internal

bus termination. Therefore, the first and last nodes of the bus

must be included with bus termination.

In the this diagram, the built-on terminations of the D-SUB

connectors at the first and last nodes are switched on.

According to CANopen specification CiA 301.

Pin Description

1 - Not in use

2 CAN_L CAN_L bus line

3 CAN_GND CAN ground

4 - Not in use

5CAN_SHLD OptionalCAN

6 GND Optional ground

7 CAN_H CAN_H bus line

8 - Not in use

9 CAN_V+ Not supported.

Index Name Value

20.01 Ext1 commands Fieldbus A

22.11 Speed ref1 source FBA A ref 1

28.11 Frequency ref1 source FBA A ref 1

50.01 FBA A enable Enable (or select the option slot in which the module is installed)

50.02 FBA A comm loss func Fault

51.02 Node ID Set the node address of the device.

51.03 Bit rate Set the bit rate for the CANopen interface.

51.05 Profile The ABB Drives communication profile is the default value.

See the latest version of FCAN-01 CANopen adapter module

user's manual (3AFE68615500 [English]) in ABB library

(www.abb.com/drives/documents).

For more information on ABB fieldbus options and protocols,

see the fieldbus communications web page

(new.abb.com/drives/connectivity/fieldbus-connectivity).

SUB-D9

(male)

CANopen

CANopen CANopenCANopen

OFF

OFF ON

FCAN-01 manual

Fieldbus communications web

page

Specifications subject to change without notice.

3AXD50000158195 Rev B (EN) 2023-01-25

abb.com/drives

Andere Handbücher für FCAN-01

Inhaltsverzeichnis

Andere ABB Steuereinheit Handbücher

ABB

ABB CP1484 Bedienungsanleitung

ABB

ABB COM600 series Bedienungsanleitung

ABB

ABB NMBP-01 Installationshandbuch

ABB

ABB FPTC-01 Bedienungsanleitung

ABB

ABB Relion REC670 Gebrauchsanweisung

ABB

ABB RED615 ANSI Bedienungsanleitung

ABB

ABB SAS-W1.1E Benutzerhandbuch

ABB

ABB RER 133 Stücklistenhandbuch

ABB

ABB COM600 series Bedienungsanleitung

ABB

ABB FENA-21 Installationshandbuch

ABB

ABB COMMANDER 300 Bedienungsanleitung

ABB

ABB RET615 Bedienungsanleitung

ABB

ABB 616016-T2 Gebrauchs- und Pflegehandbuch

ABB

ABB BCU-02 Bedienungsanleitung

ABB

ABB RPBA-01 Bedienungsanleitung

ABB

ABB RBIP-01 Bedienungsanleitung

ABB

ABB RELION Series Bedienungsanleitung

ABB

ABB ACL30-04 Series Fehlerbehebungshandbuch

ABB

ABB MPS-C 2000 Bedienungsanleitung

ABB

ABB ACS800-04 Bedienungsanleitung

ABB

ABB FEPL-02 Ethernet POWERLINK Installationshandbuch

ABB

ABB 615 Series ANSI Bedienungsanleitung

ABB

ABB RMBA-01 Bedienungsanleitung

ABB

ABB ACS850-04 series Gebrauchs- und Pflegehandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung