ABB MTAC-01 Bedienungsanleitung
ABB Drives
User’s Manual
Pulse Encoder Interface Module
MTAC-01
Pulse Encoder Interface Module
MTAC-01
User’s Manual
3AFE68591091 REV B
EN
EFFECTIVE: 04.04.2006
©2006 ABB Oy. All Rights Reserved.
5
Safety
Safety
Overview
This chapter states the general safety instructions that must be
followed when installing and operating the MTAC-01 Pulse
Encoder Interface module.
The material in this chapter must be studied before attempting any
work on, or with, the unit.
In addition to the safety instructions given below, read the
complete safety instructions of the specific drive you are working
on.
General safety instructions
WARNING! All electrical installation and maintenance work on the
drive should be carried out by qualified electricians.
The drive and adjoining equipment must be properly grounded.
Do not attempt any work on a powered drive. After switching off
the input power, always allow the intermediate circuit capacitors
5 minutes to discharge before working on the drive, the motor or
the motor cable. It is good practice to check (with a voltage
indicating instrument) that the drive is in fact discharged before
beginning work.
The motor cable terminals of the drive are at a dangerously high
voltage when input power is applied, regardless of motor
operation.
There can be dangerous voltages inside the drive from external
control circuits even when the drive input power is shut off.
Exercise appropriate care when working on the unit. Neglecting
these instructions can cause physical injury or death.
6
Safety
7
Table of contents
Table of contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table of contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Preparing for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Installing the module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
01 OPERATING DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
50 ENCODER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
19 TIMER & COUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Faults/Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
8
Table of contents
9
Installation
Installation
Preparing for installation
MTAC-01 module
The MTAC-01 Pulse Encoder Interface module is an interface for
connecting a digital pulse encoder to an ACS350 drive. A pulse
encoder should be used if accurate speed or position (angle)
feedback from the motor shaft is required.
Module layout
Compatibility
The MTAC-01 module is compatible with all ACS350 drives. To
confirm compatibility with a particular pulse encoder, compare the
pulse encoder requirements to Specifications on page 25.
SCR
A
B
Z
GND
Vin
Vout
10
Installation
Installing the module
Delivery check
The MTAC-01 module package contains:
• MTAC-01 module
• grounding stand-off
• panel port adapter
• this manual.
Mounting
WARNING! Follow the safety instructions given in this manual and
in the ACS350 User’s Manual [3AFE68462401 (English)].
To mount the MTAC-01 module:
1. If not already off, disconnect the input power from the drive.
After disconnecting the input power, wait for 5 five minutes
before you start working on the drive.
2. Remove the possible control panel or panel cover from the
drive.
3. Remove the grounding screw in the top left corner of the drive’s
control panel slot and install the grounding stand-off in its place.
4. Ensure that the panel port adapter is attached to either the
panel port of the drive or the mate part of the MTAC-01 module.
5. Gently and firmly install the MTAC-01 module to the drive’s
panel slot directly from the front.
Note: Signal and power connections to the drive are automatically
made through a 6-pin connector.
6. Ground the module by inserting the screw removed from the
drive in the top left corner of the MTAC-01 module. Tighten the
screw.
Inhaltsverzeichnis
Andere ABB Steuereinheit Handbücher
ABB
ABB MotiFlex e100 OPT-MF-005 Bedienungsanleitung
ABB
ABB RDCO-01 Bedienungsanleitung
ABB
ABB CDPI-01 Bedienungsanleitung
ABB
ABB ACQ580-34 Bedienungsanleitung
ABB
ABB ACQ810 Bedienungsanleitung
ABB
ABB Symphony Harmony Series Bedienungsanleitung
ABB
ABB Welcome M2306 Bedienungsanleitung
ABB
ABB +P906 Bedienungsanleitung
ABB
ABB TA571-SIM Bedienungsanleitung
ABB
ABB ACS850 series Bedienungsanleitung
ABB
ABB ACS 600 MultiDrive Bedienungsanleitung
ABB
ABB MNS-MCC Bedienungsanleitung
ABB
ABB FDNA-01 Installationshandbuch
ABB
ABB RDIO-01 Bedienungsanleitung
ABB
ABB FCAN-01 Bedienungsanleitung
ABB
ABB RELION 650 SERIES Kurzanleitung
ABB
ABB RELION 650 SERIES Bedienungsanleitung
ABB
ABB RPBA-01 Bedienungsanleitung
ABB
ABB ACS880-34 Bedienungsanleitung
ABB
ABB FMBA-01 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
