ABB RELION 650 SERIES Datenblatt
Relion® 650 SERIES
DNP, 650 series
Version 1.1 ANSI
Point list manual
Document ID: 1MRK 511 244-UUS
Issued: November 2019
Revision: A
Product version: 1.1
© Copyright 2011 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written permission
from ABB, and the contents thereof must not be imparted to a third party, nor used for any
unauthorized purpose.
The software or hardware described in this document is furnished under a license and may be
used or disclosed only in accordance with the terms of such license.
Trademarks
ABB and Relion are registered trademarks of ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective
holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
ABB AB
Substation Automation Products
SE-721 59 Västerås
Sweden
Telephone: +46 (0) 21 32 50 00
Facsimile: +46 (0) 21 14 69 18
http://www.abb.com/substationautomation
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons
responsible for applying the equipment addressed in this manual must satisfy themselves that
each intended application is suitable and acceptable, including that any applicable safety or other
operational requirements are complied with. In particular, any risks in applications where a system
failure and/or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the person or entity
applying the equipment, and those so responsible are hereby requested to ensure that all
measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be completely ruled out.
In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other
than under explicit contractual commitments, in no event shall ABB be responsible or liable for any
loss or damage resulting from the use of this manual or the application of the equipment.
Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility (EMC
Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage
limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB
in accordance with the product standards EN 50263 and EN 60255-26 for the EMC directive, and
with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive. The IED is
designed in accordance with the international standards of the IEC 60255 series.
Table of contents
Section 1 Introduction......................................................................................................... 3
1.1 This manual.......................................................................................................................................... 3
1.2 Intended audience...............................................................................................................................3
1.3 Product documentation.................................................................................................................... 4
1.3.1 Product documentation set............................................................................................................4
1.3.2 Document revision history..............................................................................................................5
1.3.3 Related documents...........................................................................................................................5
1.4 Symbols and conventions..................................................................................................................7
1.4.1 Safety indication symbols............................................................................................................... 7
1.4.2 Manual conventions..........................................................................................................................7
1.4.3 Functions included in 650 series IEDs.......................................................................................... 8
Section 2 DNP3 data mappings.........................................................................................15
2.1 Overview..............................................................................................................................................15
2.2 Point list for the 650 series IEDs.................................................................................................... 15
Section 3 DNP3 protocol implementation....................................................................... 37
3.1 DNP3 device profile...........................................................................................................................37
3.2 DNP3 implementation table........................................................................................................... 40
Section 4 Glossary.............................................................................................................. 45
Table of contents
DNP, 650 series 1
Point list manual
© Copyright 2011 ABB. All rights reserved
2
Section 1 Introduction
1.1 This manual
GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v12
The point list manual describes the outlook and properties of the data points specific to the IED.
The manual should be used in conjunction with the corresponding communication protocol
manual.
1.2 Intended audience
GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v6
This manual addresses the communication system engineer or system integrator responsible for
pre-engineering and engineering for communication setup in a substation from an IED
perspective.
The system engineer or system integrator must have a basic knowledge of communication in
protection and control systems and thorough knowledge of the specific communication protocol.
1MRK 511 244-UUS A Section 1
Introduction
DNP, 650 series 3
Point list manual
© Copyright 2011 ABB. All rights reserved
1.3 Product documentation
1.3.1 Product documentation set GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v9
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manual
Operation manual
Installation manual
Service manual
Engineering manual
Commissioning manual
Communication protocol
manual
Technical manual
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Planning & purchase
Engineering
Installing
Commissioning
Operation
Maintenance
Decommissioning
deinstalling & disposal
Application manualApplication manual
Operation manualOperation manual
Installation manualInstallation manual
Service manualService manual
Engineering manualEngineering manual
Commissioning manualCommissioning manual
Communication protocol
manual
Communication protocol
manual
Technical manualTechnical manual
en07000220.vsd
IEC07000220 V1 EN-US
Figure 1: The intended use of manuals in different lifecycles
The engineering manual contains instructions on how to engineer the IEDs using the different
tools in PCM600. The manual provides instructions on how to set up a PCM600 project and insert
IEDs to the project structure. The manual also recommends a sequence for engineering of
protection and control functions, LHMI functions as well as communication engineering for IEC
60870-5-103, IEC 61850 and DNP3.
The installation manual contains instructions on how to install the IED. The manual provides
procedures for mechanical and electrical installation. The chapters are organized in chronological
order in which the IED should be installed.
The commissioning manual contains instructions on how to commission the IED. The manual can
also be used by system engineers and maintenance personnel for assistance during the testing
phase. The manual provides procedures for checking of external circuitry and energizing the IED,
parameter setting and configuration as well as verifying settings by secondary injection. The
manual describes the process of testing an IED in a substation which is not in service. The
chapters are organized in chronological order in which the IED should be commissioned.
The operation manual contains instructions on how to operate the IED once it has been
commissioned. The manual provides instructions for monitoring, controlling and setting the IED.
Section 1 1MRK 511 244-UUS A
Introduction
4DNP, 650 series
Point list manual
© Copyright 2011 ABB. All rights reserved
Andere Handbücher für RELION 650 SERIES
43
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere ABB Steuereinheit Handbücher
ABB
ABB IEC 61850 Edition 2 Bedienungsanleitung
ABB
ABB ACSM1-04 Series Bedienungsanleitung
ABB
ABB Relion 615 series Bedienungsanleitung
ABB
ABB FPTC-01 Bedienungsanleitung
ABB
ABB FSCA-01 Installationshandbuch
ABB
ABB Relion 630 Series Kurzanleitung
ABB
ABB FCAN-01 Bedienungsanleitung
ABB
ABB relion REF615 Bedienungsanleitung
ABB
ABB NMBP-01 Installationshandbuch
ABB
ABB ACS880-34 Bedienungsanleitung
ABB
ABB 650 series Gebrauchsanweisung
ABB
ABB RELION 650 SERIES Kurzanleitung
ABB
ABB NCSA-01 CS 31 Installationshandbuch
ABB
ABB COM600 series Bedienungsanleitung
ABB
ABB REF542plus Bedienungsanleitung
ABB
ABB CP1484 Bedienungsanleitung
ABB
ABB AI111.0 Bedienungsanleitung
ABB
ABB ACS880 Series Betriebsanleitung
ABB
ABB RET615 Bedienungsanleitung
ABB
ABB REF 542plus Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
