ABB REC603 Bedienungsanleitung

Wireless Controller

REC601/603

Product Guide

Contents

1. Description.....................................................................3

2. Applications....................................................................4

3. Battery condition monitoring...........................................8

4. Motor overload protection..............................................9

5. Inputs and outputs / Physical interfaces.........................9

6. Communication............................................................13

7. Technical data..............................................................14

8. Mounting methods.......................................................19

9. Ordering data...............................................................19

10. Accessories and ordering data....................................22

11. Tools...........................................................................22

12. Terminal diagrams.......................................................23

13. References..................................................................25

14. Document revision history...........................................25

Disclaimer

The information in this document is subject to change without notice and should not be construed as a commitment by ABB Oy. ABB Oy assumes no responsibility

for any errors that may appear in this document.

Trademarks

ABB is a registered trademark of ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks of their

respective holders.

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

2 ABB

1. Description

The Wireless Controllers REC601/603 are

compact, solution based devices for the remote

control and monitoring of secondary substations

such as network disconnectors, load break

switches and Ring Main Units (RMU’s) in

distribution networks.

The Wireless Controllers REC601/603 enable the

SCADA system to wirelessly monitor and control

the field devices over the public communication

infrastructure (GPRS).

The Wireless Controllers REC601/603 utilize the

built-in GPRS features for reliable and secure end-

to-end communication providing remote

monitoring and control of a single object with

Wireless Controller REC601, or up to three (3)

objects with Wireless Controller REC603.

The use of Wireless Controllers REC601/603 in

distribution networks improves the quality of

power distribution and dramatically reduces the

outage time in affected areas. The areas directly

adjacent to these affected areas would also show

reduced outages and overall effects. It also

reduces the capital expenditures in the

distribution network by limiting the replacement of

legacy devices and contributes to more direct

cost savings by facilitating preventative

maintenance. Wireless Controllers REC601/603

are also ideally suited to be retrofitted to existing

disconnectors and thus enabling remote control

of these devices and further extending the life

cycle of the disconnector itself.

SCADA (ABB MicroSCADA)

IEC-104 M2M Gateway

• Static IP addresses

• Firewall and VPN

TCP/IP

IEC-104 IEC-104

TCP/IP

Wireless Controller REC601/603 Wireless Gateway RER601/603

SPA

IEC-101

ABB IED

ABB load break switches

GPRS

Secure end-to-end VPN tunneling in public network

GUID-5BB3E76A-52DD-4A42-A1EE-122D795C95E6 V1 EN

Figure 1. Typical communication system example

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0 Issued: 2011-09-02

Revision: A

ABB 3

2. Applications

The Wireless Controllers REC601/603 are

important and powerful components in an

automated distribution network. Connected to the

central control system (SCADA/DMS) – that

manages the utility network - they serve as the

core of the secondary substation automation

system. These devices are recommended devices

for multiple disconnector or distribution

transformer applications in distribution networks

that require specifications and/or features like

listed below.

• Highly reliable control and monitoring of up to

three (3) objects (per REC603):

– Disconnector position indications with front

LEDs

– Separate LED indicators for earthing status

– Supports both local and remote disconnector

control

– More than one Wireless Controller

REC601/603 can be connected in a single

location to facilitate the Ethernet enabled

control and monitoring of more than three (3)

disconnectors

• Overload protection of actuator motors

– Load current measured in the motor circuit

– Measurement of object transition time

– Energy limit based motor overload protection

(“software fuse”)

• Always on two-way communication based on

GPRS via an M2M gateway

– Redundant IEC 60870-5-104 connections

provide extra availability

– Communication monitoring and automatic

connection re-establishment

– High level data security through internal VPN

and Firewall

– Possibility to act as an IEC 60870-5-101

master (router) for another communicating

sub-device (for example metering unit or fault

passage indicator)

• Built-in battery charger with advanced battery

control:

– Temperature compensated charging

– Battery monitoring/testing (condition

monitoring)

– Deep discharge protection

• Heater control to limit effects of ambient

temperature variations, such as condensation,

etc.

• Real-time clock for accurate event time-tagging

• Robust aluminium casing design for easy DIN

rail mounting

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

4 ABB

GUID-B0E0CD80-91B5-4437-B5B0-0BB47638EBFD V1 EN

Figure 2. Distribution automation system overview

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

ABB 5

Application examples

REC601

aux

UEMC 50

Hall

sensor

+24V DC

Battery charging

Battery test

Heater control

Remote

off

GUID-2EA84B83-9D8A-4B3F-AC97-D99930FCB53B V1 EN

Figure 3. Within the UEMC 50 the REC601 unit is used for the remote control of a disconnector. The motor

operating device is placed in the same UEMC 50 enclosure as the other equipment.

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

6 ABB

REC603

aux

80-265V ac/dc

or 18-80V dc

kWh

kVArh

LV compartment in RMU

Remote

o

Hall

SF6Alarm

Serial port

+24V DC

sensor

Battery charging

Battery test

Heater control

GUID-FA91F00E-70D2-404C-8F7A-AEA72FB7F30B V1 EN

Figure 4. A REC603 unit used for remote control of a Ring Main Unit

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

ABB 7

REC601

aux

UEMC Control Cabinet

Remote

off

Hall

+24V DC

Battery charging

Battery test

Heater control

sensor

GUID-D6E454C7-00B1-4D98-8EFE-62048B5E37D4 V1 EN

Figure 5. Within the UEMC control cabinet the REC601 unit is used for remote control of a disconnector. The

motor operating device is fitted to the disconnector.

3. Battery condition monitoring

The Wireless Controllers REC601/603 are

equipped with condition based functionality that

make the conditioning monitoring of the built-in

battery of the device possible and optimize the

lifetime and maintenance intervals of the back-up

batteries in the control assembly.

The back-up battery could periodically (scheduled

by operator) be tested by switching off the

charger and switching on the dummy load.

Current and voltage measurements are taken for

a defined period of time (discharging time period).

Based on these measurements of the battery’s

current and voltage levels, an assessment is

made regarding the battery’s condition and

remaining operational capacity (in Ah). If the

assessment shows that the battery has a

significant depletion in capacity an IEC

60870-5-104 alarm event would then be

generated in the system.

Also the Wireless Controllers REC601/603 feature

the ability to protect the battery against complete

discharge. This is achieved by the fact that the

battery voltage is always measured in network

fault conditions (primary power source is

disconnected). If the measured battery voltage

level is below a defined limit (assumed as a

“battery failure”) an IEC 60870-5-104 alarm event

would then be generated in the system and the

load is disconnected from the battery.

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

8 ABB

4. Motor overload protection

The Wireless Controllers REC601/603 are

equipped with condition based functionality that

assists in the monitoring and management of the

disconnector motor by using over current

detection and shut down of the motor that is

connected to the device.

The over current detection is initialized as soon as

a switch-on command is received by the motor.

This overload detection process is based on

measurements done by a Hall-Effect Current

Transducer (optional accessory) for load current

and control duration measurements. As soon as a

predefined energy limit is exceeded, as shown by

the mentioned measurements, the motor is shut

down by disconnecting it via the relay output on

the Wireless Controllers REC601/603.

5. Inputs and outputs / Physical interfaces

The Wireless Controllers REC601/603 are

equipped with numerous input and output

connections to manage control operations that

are communicated via the wireless (GPRS)

capabilities of the devices.

Wireless Controller REC603 has 16 binary inputs

(REC601 has 6) for monitoring and alarms, and 7

binary outputs for disconnector control (REC601

has 3). Both REC601 and REC603 devices each

have 2 binary outputs and 2 analog inputs for

battery control within the ranges of 0-30 V, 0-10

A. Further both the devices each have a binary

output for over current motor control as well as

an analog input for motor control within the range

0-15 A.

Additionally the devices are equipped with a

transducer input and heater control output.

The Wireless Controllers REC601/603 also has

two serial ports (with DIP switches for serial port

2 hardware configuration) and an Ethernet

connector for communication and data transfer.

Also there is a SIM card insertion slot with SIM

card tray and antenna connector.

The status of the operational system is shown by

various groupings of LED light indicators. More

detailed information can be sourced via the

supported WebHMI.

Front panel LEDs

The Wireless Controllers REC601/603 are

equipped with 8 (eight) groups of LEDs indicating

the complete operational status of the device.

They are located on the device’s front panel and

are identified by accompanying labels.

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

ABB 9

Table 1. Description of available LEDs on the front panel

LED LED status Description

VPN On VPN connection is up

Blink VPN connection is starting

Off VPN connection is disabled

Power/Error On Operating power is turned on

Off Operating power is turned off

Function On Device is starting

Blink Device is operating normally

Eth On Ethernet link is up

Blink Ethernet link is transferring data

Off Ethernet link is down

GPRS Blink GPRS is starting or transferring data

Off GPRS is inactive

AC and LINK LEDs AC Connected to AC power

LINK IEC 60870-5-104 control link to

SCADA is active

Disconnector1) OPEN Open position indication

CLOSE Close position indication

LOCAL/REMOTE Local / remote control indication

Grounding disconnector2) OPEN Open position indication

CLOSE Close position indication

1) Applicable for disconnectors 1, 2 or 3 (for REC603 – REC601 only has 1 disconnector)

2) Applicable for grounding disconnectors 1, 2 or 3 (for REC603 – REC601 only has 1 grounding disconnector)

Wireless Controller 1MRS757423 A

REC601/603

Product version: 1.0

10 ABB

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ABB Controller Handbücher

ABB

ABB ACS 800 Series Bedienungsanleitung

ABB

ABB IRC5 Compact Bedienungsanleitung

ABB

ABB NIESSEN 2260 Series Bedienungsanleitung

ABB

ABB ControlMaster CM10 Bedienungsanleitung

ABB

ABB PSTX 30***105 Bedienungsanleitung

ABB

ABB IRC5 Compact Bedienungsanleitung

ABB

ABB ACS880-07 Bedienungsanleitung

ABB

ABB PSE18 Leitfaden

ABB

ABB PSE18 Bedienungsanleitung

ABB

ABB SACE Tmax XT Series Bedienungsanleitung

ABB

ABB RVC Bedienungsanleitung

ABB

ABB i-bus KNX AC/S 1.x.1 Series Bedienungsanleitung

ABB

ABB ACS320 series Bedienungsanleitung

ABB

ABB ARC600 Bedienungsanleitung

ABB

ABB ACH550-PCR Bedienungsanleitung

ABB

ABB IRC5 Compact Benutzerhandbuch

ABB

ABB Relion RED615 Bedienungsanleitung

ABB

ABB Relion 620 Series Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

ABB

ABB ACH550 series Bedienungsanleitung

ABB

ABB ACS800-U4 Bedienungsanleitung

ABB

ABB 6153 EB-500 Bedienungsanleitung

ABB

ABB ControlMaster CM15 Schulungshandbuch

ABB

ABB ACB530 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch

Regin

Regin CORRIGO L10 Bedienungsanleitung