ABB ACH580-01 VxR R1 Bedienungsanleitung

—

ACH580-01 VxR, UL Type 1

Frame R1/R2

Base drive replacement instructions

Purpose or Scope

The following are the instructions for replacing an ACH580-01 UL Type 1 and 12 (Frames

R1 & R2) drive in VxR enclosures.

Equipment required*:

– Replacement drive (see note below)

– T20 bit

– T30 bit

– PZ2 bit

– PZ3 bit

– Torque wrench

– Zip ties

Basic overview of steps

– Back-up drive parameters (if you can)

– Remove power and verify after 5 minutes

– Remove covers

– Disconnect all wiring

– Remove drive

– Prepare replacement drive

– Remove conduit assembly

– Install in reverse order

– Check connections

– Power drive

– Reprogram and test

Notes and cautions

CAUTION! Review complete safety and electrical considerations prior

to replacing the drive. See ACH580 IOM (3AXD50000049127).

CAUTION! Two people are recommended for this job. The drive is

heavy and can fall, causing property damage and injury.

* Not all of these tools are needed for each frame size.

2REPLACEMENT INSTRUCTIONS | ACH580-01 VXR UL TYPE 1 , R1/R2

Step Instruction Diagram

1 NOTE: If needed, back-up parameters prior to disconnecting power.

Turn off source power and wait 5 minutes for the DC bus capacitors

to discharge.

Turn handle to the off position.

2 Using a T20 bit, loosen and remove two (2) M4x16 screws securing

the enclosure cover.

Save hardware.

3 Remove drive cover by pushing up on the sides as indicated by

arrow.

Recycle drive cover.

3REPLACEMENT INSTRUCTIONS | ACH580-01 VXR UL TYPE 1 , R1/R2

Step Instruction Diagram

4 Perform voltage check to confirm no voltage is present.

NOTE: If you have control wiring connected to the Control Unit,

disconnect at this time.

5 Cut zip tie Aand disconnect the RS485 cable Bfrom the drive

by pulling out the terminal block.

NOTE: Remove any additional drive I/O wiring.

6 Using a PZ2 bit, loosen and remove wires from the input terminals

of the drive.

Using a PZ2 bit, loosen and remove wires from the motor terminals

of the drive.

Using a PZ3 bit, loosen and remove ground wire from the drive.

4REPLACEMENT INSTRUCTIONS | ACH580-01 VXR UL TYPE 1 , R1/R2

Step Instruction Diagram

7 Using a T30 bit, loosen the two (2) bottom M6 screws securing the

drive, four (4) turns of the screw.

NOTE: Do not remove the screw completely. Only loosen enough to

be able to lift the drive off the screws.

8 Using a T30 bit, loosen and remove the top two (2) M6 screws

securing the drive.

Carefully lift the drive out of channel.

9 Unpack the replacement drive.

Remove drive cover by pushing up on the sides as indicated by

arrow.

5REPLACEMENT INSTRUCTIONS | ACH580-01 VXR UL TYPE 1 , R1/R2

Step Instruction Diagram

10 Using a T20 bit, loosen and remove two (2) M4x8 screws. Remove

conduit assembly.

Recycle the conduit assembly and hardware.

11 CAUTION! Use two people to install the drive.

Slide the drive mounting holes over the bottom two (2) screws and

slide drive in place.

Using a T30 bit, replace the two (2) M6 screws that were removed

earlier.

Torque all four (4) mounting screws to 27 in-lb (3 Nm).

6REPLACEMENT INSTRUCTIONS | ACH580-01 VXR UL TYPE 1 , R1/R2

Step Instruction Diagram

12 Secure the ground wire to the drive.

Using a PZ3 bit, torque to 14 in-lb (1.5 Nm).

13 Connect the input wires (from fuse block) to the Input Terminals of

the drive.

Yellow U1 to L1

Black V1 to L2

Red W1 to L3

R1 Frame: Using PZ2 bit, torque terminals to 5 in-lb (0.5 Nm).

R2 Frame: Using a PZ2 bit, torque terminals to 14 in-lb (1.5 Nm).

Connect the motor wires (from 1M contactor) to Motor Terminals of

the drive.

Yellow U2 to T1/U

Black V2 to T2/V

Red W2 to T3/W

R1 Frame: Using PZ2 bit, torque terminals to 5 in-lb (0.5 Nm).

R2 Frame: Using a PZ2 bit, torque terminals to 14 in-lb (1.5 Nm).

7REPLACEMENT INSTRUCTIONS | ACH580-01 VXR UL TYPE 1 , R1/R2

Step Instruction Diagram

14 Reconnect the RS485 terminal block Ato EFB on control unit and

secure with zip tie.

Reconnect any control wiring removed in steps 4 and 5.

WARNING! This configuration does not support Safe Torque Off (STO)

functionality in bypass mode.

15 Place the top of the drive cover on first, then press down on the

bottom.

16 Place enclosure cover in place and secure using two (2) M4x16 screws

that were removed earlier.

Using a T20 bit, torque to 14 in-lb (1.5 Nm).

17 Power and reprogram the drive.

18 Test and verify drive operation and motor direction.

19 Back-up and save parameters to the keypad prior to putting the drive

back into service.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ABB Gehäuse Handbücher

ABB

ABB MISTRAL41F Multimedia Bedienungsanleitung

ABB

ABB System pro E power Handbuch

ABB

ABB System pro E power Handbuch

ABB

ABB System pro E power PBRB0004 Handbuch

ABB

ABB ACH580-01 PxR R3 Bedienungsanleitung

ABB

ABB MISTRAL41W Multimedia Bedienungsanleitung

ABB

ABB System pro E power PDLB8126-PDLB1126 Handbuch

ABB

ABB System pro E power PUPM1800 Handbuch

ABB

ABB ACH580-01 PxR Frame R2 Bedienungsanleitung

ABB

ABB ACS550 Series Bedienungsanleitung

ABB

ABB Totalflow Cold Weather Enclosure Bedienungsanleitung

ABB

ABB UniSec DY800 Handbuch

ABB

ABB STRIEBEL & JOHN MISTRAL65 Bedienungsanleitung

ABB

ABB PPKA0400 Bedienungsanleitung

ABB

ABB ACS150 series Bedienungsanleitung

Beliebte Gehäuse Handbücher anderer Marken

SilentiumPC

SilentiumPC Armis AR5 Handbuch

Pulsar

Pulsar 17/TRP80/DSPR Bedienungsanleitung

Thermaltake

Thermaltake V150 TG Bedienungsanleitung

MSI

MSI MPG SEKIRA 500X Bedienungsanleitung

Antec

Antec Dark fleet DF-10 Bedienungsanleitung

Peavey

Peavey DS 1502 Bedienungsanleitung

D-Link

D-Link ShareCenter Pro DNS-1550-04 Bedienungsanleitung

Rosewill

Rosewill RX82-U(JBOD) Bedienungsanleitung

QNAP

QNAP SAS JBOD CLI 1.0 Bedienungsanleitung

GAMDIAS

GAMDIAS Talos P1 Bedienungsanleitung

Auvs

Auvs KR615 Bedienungsanleitung

Digitus

Digitus DA-71114 Bedienungsanleitung

CommScope

CommScope FDH 3000 Bedienungsanleitung

FS FHD-FWME4 Bedienungsanleitung

JBL

JBL CS1215T Bedienungsanleitung

Pulsar

Pulsar ARAD-S4 Bedienungsanleitung

Pulsar

Pulsar AWO454 Bedienungsanleitung

NewerTech

NewerTech Voyager S3 Bedienungsanleitung