ABB RELION 650 SERIES Bedienungsanleitung
Relion® 650 SERIES
650 series
Version 1.1 ANSI
Installation manual
Document ID: 1MRK 514 014-UUS
Issued: November 2019
Revision: A
Product version: 1.1
© Copyright 2011 ABB. All rights reserved
Copyright
This document and parts thereof must not be reproduced or copied without written permission
from ABB, and the contents thereof must not be imparted to a third party, nor used for any
unauthorized purpose.
The software or hardware described in this document is furnished under a license and may be
used or disclosed only in accordance with the terms of such license.
Trademarks
ABB and Relion are registered trademarks of ABB Group. All other brand or product names
mentioned in this document may be trademarks or registered trademarks of their respective
holders.
Warranty
Please inquire about the terms of warranty from your nearest ABB representative.
ABB AB
Substation Automation Products
SE-721 59 Västerås
Sweden
Telephone: +46 (0) 21 32 50 00
Facsimile: +46 (0) 21 14 69 18
http://www.abb.com/substationautomation
Disclaimer
The data, examples and diagrams in this manual are included solely for the concept or product
description and are not to be deemed as a statement of guaranteed properties. All persons
responsible for applying the equipment addressed in this manual must satisfy themselves that
each intended application is suitable and acceptable, including that any applicable safety or other
operational requirements are complied with. In particular, any risks in applications where a system
failure and/or product failure would create a risk for harm to property or persons (including but
not limited to personal injuries or death) shall be the sole responsibility of the person or entity
applying the equipment, and those so responsible are hereby requested to ensure that all
measures are taken to exclude or mitigate such risks.
This document has been carefully checked by ABB but deviations cannot be completely ruled out.
In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other
than under explicit contractual commitments, in no event shall ABB be responsible or liable for any
loss or damage resulting from the use of this manual or the application of the equipment.
Conformity
This product complies with the directive of the Council of the European Communities on the
approximation of the laws of the Member States relating to electromagnetic compatibility (EMC
Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage
limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB
in accordance with the product standards EN 50263 and EN 60255-26 for the EMC directive, and
with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive. The IED is
designed in accordance with the international standards of the IEC 60255 series and ANSI C37.90.
Table of contents
Section 1 Introduction......................................................................................................... 5
1.1 This manual.......................................................................................................................................... 5
1.2 Intended audience.............................................................................................................................. 5
1.3 Product documentation.....................................................................................................................6
1.3.1 Product documentation set............................................................................................................6
1.3.2 Document revision history.............................................................................................................. 7
1.3.3 Related documents...........................................................................................................................7
1.4 Symbols and conventions................................................................................................................. 9
1.4.1 Safety indication symbols...............................................................................................................9
1.4.2 Manual conventions..........................................................................................................................9
Section 2 Safety information.............................................................................................11
2.1 Symbols on the product................................................................................................................... 11
2.2 Warnings..............................................................................................................................................11
2.3 Caution signs......................................................................................................................................12
2.4 Note signs........................................................................................................................................... 13
Section 3 Environmental aspects..................................................................................... 15
3.1 Sustainable development................................................................................................................ 15
3.2 Disposing of the IED......................................................................................................................... 15
Section 4 Unpacking, inspecting and storing................................................................. 17
4.1 Removing transport packaging......................................................................................................17
4.2 Inspecting the product.....................................................................................................................17
4.2.1 Identifying the product.................................................................................................................. 17
4.2.2 Checking delivery items................................................................................................................. 17
4.2.3 Inspecting the IED........................................................................................................................... 17
4.2.4 Returning an IED damaged in transit.......................................................................................... 17
4.3 Storing.................................................................................................................................................18
Section 5 Mounting.............................................................................................................19
5.1 Required tools....................................................................................................................................19
5.2 Checking environmental conditions and mounting space....................................................... 19
5.3 Mounting the IED...............................................................................................................................19
5.3.1 Flush mounting the IED................................................................................................................. 19
5.3.2 Rack mounting the IED...................................................................................................................21
5.3.2.1 Rack mounting a single IED..................................................................................................... 21
5.3.2.2 Rack mounting two IEDs..........................................................................................................24
5.3.3 Wall mounting the IED................................................................................................................... 26
Table of contents
650 series 1
Installation manual
© Copyright 2011 ABB. All rights reserved
5.3.4 Wall mounting with external display module............................................................................ 27
5.3.4.1 Mounting the external display module..................................................................................27
5.3.4.2 Wall mounting the main unit...................................................................................................29
5.3.5 Arranging ventilation..................................................................................................................... 30
Section 6 Connecting..........................................................................................................31
6.1 Required tools.................................................................................................................................... 31
6.2 Connecting wires...............................................................................................................................31
6.2.1 Connecting screw-compression type wires.............................................................................. 31
6.2.2 Connecting ring-lug type wires.................................................................................................... 31
6.3 Connecting protective grounding................................................................................................. 32
6.4 Connecting analog signals..............................................................................................................34
6.4.1 Connecting current and voltage inputs .....................................................................................35
6.4.2 Connecting IED with a test switch.............................................................................................. 36
6.5 Connecting power supply............................................................................................................... 36
6.6 Connecting communication........................................................................................................... 38
6.7 Connecting external display module.............................................................................................39
Section 7 Checking installation........................................................................................ 41
7.1 Identifying hardware and software version.................................................................................41
7.2 Checking mounting...........................................................................................................................41
7.3 Energizing the IED.............................................................................................................................41
Section 8 Removing, repairing and exchanging............................................................. 43
8.1 Product lifecycle................................................................................................................................ 43
8.2 Checking IED information............................................................................................................... 43
8.3 Removing the IED..............................................................................................................................43
8.4 Sending the IED for repair...............................................................................................................43
8.5 Exchanging the IED...........................................................................................................................43
Section 9 Technical data....................................................................................................45
9.1 Case and HMI display variants....................................................................................................... 45
9.1.1 Front side of the IED...................................................................................................................... 45
9.1.2 Rear side of the IED........................................................................................................................ 46
9.2 Dimensions........................................................................................................................................ 46
9.3 Enclosure class.................................................................................................................................. 47
Section 10 Accessories and ordering data........................................................................49
10.1 Mounting kits.....................................................................................................................................49
10.1.1 Flush mounting kit......................................................................................................................... 49
10.1.2 Rack mounting kit for a single IED..............................................................................................50
10.1.3 Rack mounting kit for two IEDs...................................................................................................50
10.1.4 Wall mounting kit for an IED ........................................................................................................ 51
10.1.5 Wall mounting kit for a main unit................................................................................................ 52
Table of contents
2650 series
Installation manual
© Copyright 2011 ABB. All rights reserved
10.2 Cables.................................................................................................................................................. 53
Section 11 Glossary.............................................................................................................. 55
Table of contents
650 series 3
Installation manual
© Copyright 2011 ABB. All rights reserved
4
Andere Handbücher für RELION 650 SERIES
43
Inhaltsverzeichnis
Andere ABB Relais Handbücher
ABB
ABB RD3P Bedienungsanleitung
ABB
ABB Relion 615 series Bedienungsanleitung
ABB
ABB MG-6 Handbuch
ABB
ABB CIRCUIT SHIELD 437W Series Bedienungsanleitung
ABB
ABB SPAJ 142 C Stücklistenhandbuch
ABB
ABB CM Handbuch
ABB
ABB SPAJ 160 C Stücklistenhandbuch
ABB
ABB SGR-51 Bedienungsanleitung
ABB
ABB TRB Series Handbuch
ABB
ABB Tmax PR222DS/P Gebrauchsanweisung
ABB
ABB SA-1 Handbuch
ABB
ABB TF140DU Bedienungsanleitung
ABB
ABB SC Handbuch
ABB
ABB SPAU 331 C Stücklistenhandbuch
ABB
ABB RED615 ANSI Bedienungsanleitung
ABB
ABB CT-AHS Firmware-Update
ABB
ABB RD3M Bedienungsanleitung
ABB
ABB CM Series Bedienungsanleitung
ABB
ABB REM 610 Bedienungsanleitung
ABB
ABB Relion 615 series Bedienungsanleitung
