ABB Zenith ZTX Series Bedienungsanleitung
OPERATION, MAINTENANCE, AND INSTALLATION GUIDE
Zenith ZTX series
For ZTX series automatic transfer
switches, 30-1200 A, 200-480 Vac
2
2
1
—
Receiving, handling and storage
Receiving and handling
Upon receipt, carefully inspect the trans-
fer switch for damage that may have oc-
curred during transit. If damage is evi-
dent, or there is visible indication of
rough handling, immediately file a dam-
age claim with the transportation com-
pany, and notify your local ABB sales
office.
Do not remove the shipping packaging
until ready to install the switch.
Storage
If the unit will not be placed into service
immediately, store the transfer switch in
its original package in a clean, dry loca-
tion. To prevent condensation, maintain a
uniform temperature. Store the unit in a
heated building, allowing adequate air cir-
culation and protection from dirt and
moisture. Storing the unit outdoors could
cause harmful condensation inside the
transfer switch enclosure.
HAZARD OF EQUIPMENT
OVERTURNING
When moving with a fork lift, do not re-
move the shipping packaging until the de-
vice is in its final location.
Failure to follow this instruction may
result in personal injury or equipment
damage.
Warning
Indicates a hazardous situation that,
if not avoided, could result in death or
serious injury.
4
Zenith ZTX Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE
—
Read these safety instructions
carefully before using this product!
HAZARD OF ELECTRIC SHOCK,
EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective
equipment and follow safe electrical
work practices.
• This equipment must only be installed
and serviced by qualified electrical per-
sonnel.
• Before performing visual inspections,
tests, or maintenance on the equip-
ment, disconnect all sources of electric
power. Assume that all circuits are live
unless they are completely de-ener-
gized, tested, grounded, and tagged.
Pay particular attention to the design of
the power system. Consider all sources
of power, including the possibility of
backfeeding.
• Disconnect all sources of electric power
before removing or making source side
or load side connections to the transfer
switch.
• Always use a properly rated voltage
sensing device at all line and load con-
nections to confirm transfer switch is
disconnected from all live electrical
sources.
• Turn off power supplying transfer
switch before doing any other work on
or inside switch.
Failure to follow these instructions could
result in death or serious injury.
Danger
Indicates a hazardous situation that,
if not avoided, will result in death or
serious injury.
5
12
—
Operation, maintenance,
and installation
instruction
Automatic transfer
switches, Zenith ZTX
series ATS
INSTALLATION INSTRUCTIONS,
ZENITH ZTX SERIES ATS,
CHAPTERS 9–11
OPERATION AND MAINTENANCE
INSTRUCTIONS, ZENITH
ZTX SERIES ATS,
CHAPTERS 1–8
6
Zenith ZTX Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE
1
7
1
—
Operation and
maintenance instruction
Automatic transfer
switches, Zenith ZTX
series ATS
1. Introduction 11
1.1 Hazard Categories 11
1.2 Definitions 12
1.3 Warranty 13
1.4 Product Specification 14
2. Product overview 15
2.1 General overview 16
2.1.1 Operation types 17
2.2 HMI 18
2.3 Zenith ZTX series features 19
2.4 Typical applications 22
2.5 Sequence of operations 24
2.5.1 Switching sequence / Automatic 24
2.6 Special features description 26
2.6.1 Automatic configuration 26
2.6.2 In-phase monitor 26
2.6.3 Powering supply scenarios 26
8
Zenith ZTX Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE
1
3. General operation 27
3.1 Position indication 27
3.2 Operating and locking 28
3.3 Manual handle operation 29
3.4 Return to automatic mode,
operating by HMI 30
3.5 LED functionality in HMI 31
3.6 Using Level 2 (DIP) control interface HMI 33
3.6.1 Keypad 33
4. Navigating HMI menu 35
4.1 Configuration by DIP switch 35
5. Electronic accessories 37
5.1 Using Ekip Connect -software 38
5.2 Using Ekip Bluetooth-module 39
5.2.1 LED indications 39
5.3 Using Ekip Programming -module 40
5.3.1 LED indications 40
9
1
6. Troubleshooting 41
6.1 Alarms 41
6.2 Warnings 43
6.3 Information 44
7. Technical data 45
7.1 General technical data 45
7.2 Circuit diagrams 48
7.3 Overall dimensions 49
8. Maintenance 53
10
Zenith ZTX Series ATS, OPERATION, MAINTENANCE, AND INSTALLATION GUIDE
1
Andere Handbücher für Zenith ZTX Series
1
Inhaltsverzeichnis
Andere ABB Schalten Handbücher
ABB
ABB NE810 Bedienungsanleitung
ABB
ABB ZX1.5-R Bedienungsanleitung
ABB
ABB DY365 Series Bedienungsanleitung
ABB
ABB Tmax Bedienungsanleitung
ABB
ABB 3299-22958 Bedienungsanleitung
ABB
ABB UniGear Series Bedienungsanleitung
ABB
ABB ATS022 Bedienungsanleitung
ABB
ABB E 232 E-230N Bedienungsanleitung
ABB
ABB FAP1021 Series Bedienungsanleitung
ABB
ABB OTM C 21D Bedienungsanleitung
ABB
ABB FAP 1001 Bedienungsanleitung
ABB
ABB VD4 Series Kurzanleitung
ABB
ABB EDS500 Series Bedienungsanleitung
ABB
ABB Fox 21 Bedienungsanleitung
ABB
ABB EDS500 Series Bedienungsanleitung
ABB
ABB OTM C Series Bedienungsanleitung
ABB
ABB OTM_C Series Benutzerhandbuch
ABB
ABB OTM C 21D Bedienungsanleitung
ABB
ABB F-400 Bedienungsanleitung
ABB
ABB Power Break II Bedienungsanleitung
