ABL AIP-1MBF Bedienungsanleitung

Cost-effective HD IR Waterproof Fixed Network Camera

Quick Start Guide

Version 1.2.0

Welcome

Thank you for purchasing our network camera!

This quick start guide is designed to be a reference tool for your system.

Please keep this start guide well for future reference.

Please open the accessory bag to check the items one by one in accordance with the list below.

Contact your local retailer ASAP if something is missing or damaged in the bag.

Before your operation please read the following instructions carefully.

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.

The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited

power source is rated 12V DC in the IEC60950-1. (Refer to product introduction) Please note: Do not

connect these two power supplying sources to the device at the same time; it may result in

device damage!

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling

or installation.

We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and

installation.

3．Installation

Do not apply power to the camera before completing installation.

Please install the proper power cut-off device during the installation connection.

Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.

We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,

inflammable, explosive substances and etc.

Please keep it away from the electromagnetic radiation object and environment.

Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.

Otherwise it may result in CCD (CMOS) optical component damage.

Please keep the sound ventilation.

Do not allow the water and other liquid falling into the camera.

Thunder-proof device is recommended to be adopted to better prevent thunder.

The grounding studs of the product are recommended to be grounded to further enhance the reliability

of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance

work.

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens

surface.

Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the

device.

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.

Dome enclosure is the optical component, do not touch the enclosure when you are installing the

device or clean the enclosure when you are doing maintenance work. Please use professional optical

clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result

in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.

Before installation, please open the package and check all the components are included.

Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

Quick Start Guide

Installation Accessories Bag

iii

Table of Contents

1Framework.....................................................................................................................1

1.1 Multiple-function Combination Cable.................................................................1

1.2 Framework and Dimension...............................................................................1

2Device Installation .........................................................................................................3

3Quick Configuration Tool...............................................................................................5

3.1 Overview...........................................................................................................5

3.2 Operation..........................................................................................................5

4Web Operation ..............................................................................................................7

4.1 Network Connection..........................................................................................7

4.2 Login and Main Interface...................................................................................7

Appendix Toxic or Hazardous Materials or Elements ........................................................10

1 Framework

1.1 Multiple-function Combination Cable

You can refer to the following figure for multiple-function combination cable information. See

Figure 1-1.

Figure 1-1 Multiple-function combination cable

Please refer to the following sheet for detailed information.

No.

Port Name

Function

Connection

Note

LAN

Network port

Ethernet

port

Connect to standard Ethernet cable.

DC12V

Power input

port

Power input port. Input DC 12V.

1.2 Framework and Dimension

Please refer to the following figure for dimension information. The unit is mm. See Figure 1-2

and Figure 1-3.

Figure 1-2 Dimension illustration 1

Figure 1-3 Dimension illustration 2

2 Device Installation

Please follow the steps listed below to install the device. Please refer to Figure 2-1 and Figure

2-2 for reference.

Paste the installation map on the surface of the wall or the ceiling.

Dig the installation holes according to the installation map.

Open the accessories bag and then take the expansion bolt out. Insert the expansion

bolt into the installation holes.

Take the screws from the accessories bag and then use them to secure the device on

the installation surface of the wall or the ceiling.

Connect the corresponding cables.

Figure 2-1 Device installation illustration 1

Use the cross-head screwdriver to loosen the adjust screw.

Turn the device in different directions to make it suitable for the monitor position.

Use the cross-head screwdriver to fix the adjust screw firmly.

Figure 2-2 Device installation illustration 2

3 Quick Configuration Tool

3.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you

can use it to upgrade the device.

Please note the tool only applies to the IP addresses in the same segment.

3.2 Operation

Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 3-1.

In the device list interface, you can view device IP address, port number, subnet mask, default

gateway, MAC address and etc.

Figure 3-1 Search interface

Select one IP address and then right click mouse, you can see an interface is shown as in Figure

3-2.

Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 3-2 Search interface 2

If you want to modify the device IP address without logging in the device web interface, you can

go to the configuration tool main interface to set.

In the configuration tool search interface (Figure 3-1), please select a device IP address and then

double click it to open the login interface. Or you can select an IP address and then click the

In Figure 3-3, you can view device IP address, user name, password and port. Please modify the

corresponding information to login.

Please note the port information here shall be identical with the port value you set in TCP port in

Web Network interface. Otherwise, you cannot login the device.

If you are using device background upgrade port 3800 to login, other setups are all invalid.

Figure 3-3 Login prompt

After you logged in, the configuration tool main interface is shown as below. See Figure 3-4.

Figure 3-4 Main interface

For detailed information and operation instruction of the quick configuration tool, please

refer to the Quick Configuration Tool User’s Manual included in the resources CD.

Inhaltsverzeichnis

Andere ABL Sicherheitskamera Handbücher

ABL

ABL AIP-2MBV Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung