Abocom AR1000 Bedienungsanleitung

M73-APO07-110

ADSL ROUTER

Quick Installation Guide

- 1 -

Parts Names and functions

Rear view of the ADSL ROUTER

LED Indicator

Top View of ADSL ROUTER (LEDs)

- 2 -

LED Description

POWER Router Power on/off Indicator

ADSL_PWR ADSL Module Power on/off Indicator

ETH_LNK Ethernet Link Indicator

ETH_ACT Ethernet Active Indicator

ADSL_AUTO ADSL Auto Connection Indicator

ADSL_LINK ADSL Data Link Indicator

ADSL_ERR ADSL Link Error Indicator

Connectors on the Rear Panel

The following table describes the function of the connectors and switches on the ADSL

ROUTER rear panel. See the following illustration for the location of the connectors

described in the following table.

Connectors on the rear panel

Connector Label Connector Description

5VDC 5VDC Input Power Connector

Switch POWER ON/OFF SWITCH

Reset System Reset.

Console Connects this device to the serial port on your PC.

USB USB INPUT PORT

Ethernet Connects to the Ethernet port on your PC using

the Non Hub Ethernet cable supplied with your

unit, or LAN hub using a straight-through cable.

ADSL Connects this device to the wall jack.

- 3 -

Setting Up the Hardware Environment

Connecting All Cables to the Network

Perform the following procedures to set up the ADSL ROUTER.

Step 1 Connect the power adapter to the port labeled 5VDC on the rear panel of this

device.

Step 2 Connect the Ethernet cable.

One PC – ADSL Router (direct connection)

If your only have one PC, you can connect your ADSL ROUTER to the PC directly without

a hub. For a single Ethernet-equipped PC, use the "non-hub" twisted-pair crossover cable to

connect the ADSL ROUTER Ethernet port to the Ethernet port on your computer.

Home Network – ADSL Router (connection through Ethernet Switch/Hub)

If your ADSL ROUTER is connected to a home network, you may use a standard Ethernet

cable (not provided) to connect your ADSL ROUTER Ethernet port to an available port on

your home network Ethernet hub.

Step 3 Connect the ADSL cable to the ADSL ROUTER. Connect the ADSL ROUTER to

the ADSL line with the provided telephone cable.

- 4 -

Step 4 Connect one end of RS-232 cable to any free COM port in your system; Connect

the other end to “Console” port on the rear panel of the ADSL router.

Powering On the ADSL ROUTER

Step 1 Connect the power adapter to your ADSL ROUTER by plugging one end of the

power supply into an appropriate electrical outlet and the other end into port

labeled 5VDC on the rear panel of the device.

Note: To power off he ADSL ROUTER, just unplug the power supply cable from the ADSL

ROUTER rear panel POWER connector.

Step 2 Once your ADSL ROUTER is powered up, check to make sure the Power LED is

red and ON.

Step 3 If the Power LED is not lit, immediately turn off all power to the ADSL ROUTER.

- 5 -

INTERNET ACCESS

Router Mode/ IP over ATM (RFC1577)

(1) Run the “router.exe” file saved in the configuration utility. (Go to Start ÆProgramÆ

ADSL Router xx Configuration UtilityÆConfiguration Utility.)

(2) Select a PC COM port available on your computer used to connect to the ADSL Router’s

“Console” port.

(3) Check “Router Protocol” and select “IP over ATM”.

(4) Click “Properties” button.

(5) Enter “ADSL IP”, “Gateway IP”, and “Subnet Mask” addresses provided by your

service provider.

(6) Usually Ethernet IP addresses were not provided by service providers. Check to make

sure if this is your case, if yes, remember to select “Enable NAT function.”

(7) Enter the VPI and VCI numbers. Typically VPI is set to “0”.

- 6 -

(8) Click “OK” to go to “Select Config” menu. Or click “Save As File” to save the settings

for future use. Then click “Next”.

(9) Click “Configure” button. The configure utility will automatically setup the router for

you. Expect a minor delay for configuration.

Bridge mode/RFC1483 bridge

(1) Run the “router.exe” file saved in the configuration utility. (Go to Start ÆProgramÆ

ADSL Router xx Configuration UtilityÆConfiguration Utility.)

(2) Select a PC COM port available on your computer used to connect to the ADSL Router’s

“Console” port.

(3) Click “Next” button.

(4) Select Mode “Bridge” and select “RFC1483 Bridge”.

(5) Click “Properties” button.

- 7 -

(6) Enter VPI and VCI numbers. Then click “OK”.

(7) Check “LLC Encapsulation” or “VC Based Route” or “VC Based Bridge”.

(8) Click “Next” followed by “Configure”. Configure utility will automatically setup the

router for you. Expect a minor delay for the router configuration.

(9) Click “Finish”. Now you have finished ADSL Router configuration. The ADSL Router

will handshake with ADSL central site equipment (DSLAM) and try to make the ADSL

connection.

Inhaltsverzeichnis

Andere Abocom Netzwerk-Router Handbücher

Abocom

Abocom ARM804 Bedienungsanleitung

Abocom

Abocom WBR480 Bedienungsanleitung

Abocom

Abocom VDSL to Ethernet Bridge VE1000 Bedienungsanleitung

Abocom

Abocom PLS342 Bedienungsanleitung

Abocom

Abocom Wireless Router FSM612 Bedienungsanleitung

Abocom

Abocom FVR206 Bedienungsanleitung

Abocom

Abocom SW2400M Bedienungsanleitung

Abocom

Abocom P3102-4g Bedienungsanleitung

Abocom

Abocom WR104 Bedienungsanleitung

Abocom

Abocom CAS2042 Bedienungsanleitung

Abocom

Abocom PLC342 Bedienungsanleitung

Abocom

Abocom SW800 Bedienungsanleitung

Abocom

Abocom WR5205G Bedienungsanleitung

Abocom

Abocom WR5205 Bedienungsanleitung

Abocom

Abocom MH200 Bedienungsanleitung

Abocom

Abocom WR5207 Bedienungsanleitung

Abocom

Abocom HomePlug 1.0 Turbo Ethernet Adapter PLE0085 Bedienungsanleitung

Abocom

Abocom PL1000 Bedienungsanleitung

Abocom

Abocom WR5208 Bedienungsanleitung

Abocom

Abocom SW1600R Bedienungsanleitung

Abocom

Abocom SW500A Bedienungsanleitung

Abocom

Abocom SW800RE Bedienungsanleitung

Abocom

Abocom ARM904 Bedienungsanleitung

Abocom

Abocom SW800AE Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise