Acer Altos S200F Bedienungsanleitung

Altos S205F / S200F

Tower Kit

Installation Guide

Issue 1.0

1 May, 2004

Notices

Changes may be made periodically to the information in this publication without obligation to

notify any person of such revision or changes. Such changes will be incorporated in new editions

of this manual or supplementary documents and publications. This company makes no

representations or warranties, either expressed or implied, with respect to the contents hereof

and specifically disclaims the implied warranties of merchantability or fitness for a particular

purpose.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any

form or by any means, electronic, mechanical, photocopy, recording, or otherwise, without the

prior written permission of Acer Incorporated.

Issue 1.0 1 May, 2004

Altos S205F / S200F Tower Kit Installation Guide

Contents

• Introduction

•Safety

• Tools Required

• Tower Installation Kit

•Procedure

Altos S205F / S200F Tower Kit Installation Procedure

Altos S205F / S200F Tower Kit

Installation

Introduction

This document defines the installation procedure for converting the Altos S205F / S200F Rack

Enclosure storage system to a Tower system. The unpopulated enclosure and tower installation kit

are shown in Figure 1.

Safety

Warning An Enclosure can weigh up to 37kg (81lb). Do not try to lift it by yourself.

Tools Required

• Pozidrive screwdriver

(not supplied)

Tower Installation Kit

Figure 1: Tower Installation Kit with Unpopulated Enclosure

Description Quantity

Tower Foot 1

Tower Cover 1

M5 Lock Washer 4

M5 Plain Washer 4

M5 x 16 Pan Head, POZI Screw 4

M5 x 8 Pan Head, POZI Screw with Patchlock 4

Altos S205F / S200F Tower Kit Installation Procedure

Procedure

Important The enclosure must be unpopulated before you begin the tower installation. Please refer to Altos

S205F / S200F User’s Manual for details of module removal/replacement procedures.

1Remove the four bezel screw covers from the front of the enclosure chassis (if fitted).

2Place the unpopulated enclosure on the tower foot, ensuring that the drive carrier connectors are

on the left hand side of the drive bay when viewed from the front of the enclosure, see Figure 2.

Note: The drive carrier handle will open from the top when the drive carrier is inserted

correctly.

Figure 2: Drive Connector Locations

TOPTOP

Drive carrier connectors

on left side of Bay

Altos S205F / S200F Tower Kit Installation Procedure

3Secure the front of the enclosure to the tower foot using:

–2 off M5 x 16 pan head POZI screws

–2 off M5 plain washer

–2 off lock washer

(refer to Figure 3)

4Secure the rear of the enclosure to the tower foot using:

–2 off M5 x 8 pan head POZI screws with patchlock

(refer to Figure 3)

Figure 3: Securing the Enclosure to the Foot

Altos S205F / S200F Tower Kit Installation Procedure

5Slide the tower cover over the enclosure, taking care to align the tabs on the cover with the slots

in the foot.

Caution Failure to align the tabs on the cover with the slots in the foot during assembly may result in

damage to the paintwork on the foot.

The three location tabs on each side of the tower cover must locate in the three corresponding slots

on each side of the tower foot, as shown in Figure 4.

Figure 4: Locating the Tower Cover on the Foot

Tabs

Slots

Altos S205F / S200F Tower Kit Installation Procedure

6Secure the tower cover to the front of the enclosure using:

–2 off M5 x 16 pan head POZI screws

–2 off M5 plain washer

–2 off lock washer

through the two holes at the top of the enclosure.

(refer to Figure 5)

7Secure the tower cover to the rear of the enclosure using:

–2 off M5 x 8 pan head POZI screws with patchlock

(refer to Figure 5)

Figure 5: Securing the Cover

8Refit the bezel covers over the four securing screws at the front of the enclosure chassis

9Refit the modules in the enclosure in accordance with the instructions in Altos S205F / S200F User’s

Manual.

Altos S205F / S200F Tower Kit Installation Procedure

Figure 6: Populated Tower Installation

END OF PROCEDURE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Acer Netzwerk-Hardware Handbücher

Acer

Acer AN1600 F1 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung