ACME LED-MTX25 IP Bedienungsanleitung

LED-MTX25 IP

User Manual

Pleasereadtheinstructionscarefully

Contents

1. Safety Instructions..........................................................................................2

2. Technical Specifications..................................................................................3

3. Installation......................................................................................................4

3.1 Fixture Jointing..........................................................................................4

4. How to set the unit ........................................................................................5

4.1 Rear Panel.................................................................................................5

4.2 Main Function...........................................................................................6

5. How To Control The Unit .............................................................................10

5.1 Master/Slave Built In Preprogrammed Function ......................................10

5.2 DMX Controller ......................................................................................10

5.3 DMX512 Configuration...........................................................................11

6. DMX512 Connections ..................................................................................15

7. Troubleshooting............................................................................................16

8. Fixture Cleaning............................................................................................17

1. Safety Instructions

WARNING

yPlease keep this User Manual for future consultation. If you sell the fixture to

another user, be sure that they also receive this instruction booklet.

yPlease unpack and check carefully there is no transportation damage before using the

fixture.

yPlease disconnect main power before servicing and maintenance.

yThe unit must be installed in a location with adequate ventilation, at least 50cm from

adjacent surfaces. Be sure that no ventilation slots are blocked.

yThe maximum ambient temperature is Ta: 40℃. DO NOT operate it where the

temperature is higher than this.

yDO NOT connect the device to any dimmer pack.

yThe housing must be replaced if they are visibly damaged.

yUnit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand

during its operation. Turn off the power and allow about 15 minutes for the unit to cool

down before replacing or serving.

yThere are no user serviceable parts inside the fixture. Do not open the housing or attempt

any repairs by yourself. In the unlikely event your fixture may require service, please

contact your nearest dealer.

yIn the event of serious operating problem, stop using the fixture immediately. Never try to

repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage

or malfunction. Please contact the nearest authorized technical assistance center. Always

use the same type spare parts.

Please read the instructions carefully which includes important

information about the installation, operation and maintenance.

yIt’s important to ground the yellow/green conductor to earth in order to avoid

electric shock.

yDO NOT touch any wire during operation and there might be a hazard of electric shock.

yDO NOT expose the fixture to rain or moisture, in order too prevent or reduce

the risk of electrical shock or fire.

yDo not look directly at the LED light beam while the fixture is on.

2. Technical Specifications

yDMX 1/4/9/25/29 channels switchable.

ySmooth 0~100% dimming and variable strobe speeds.

yTwo operation modes: DMX, Mater/Slave mode.

yIdeal for discotheques, clubs, bars, parties, Mobile DJs, ect.

yInputVoltage: AC 100V~240V 50/60Hz

yPower consumption: 69W

yFuse: T15A

yLED: 25 x 3W WW LED

yDimension: 600 x 600 x 104 mm

yWeight: 12.5Kgs

For AC 230V 50Hz power supply, the maximum fixtures that can be connected on one power cable is 12;

For AC 120V 60Hz power supply, the maximum fixtures that can be connected on one power cable is 6.

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the

structure to which you are attaching the unit is secure and is able to support a weight of 10

times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight

of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out

of the touch of people and has no one pass by or under it.

3.1 Fixture Jointing

Firstly, plug L type Hexagon wrench into the hole back of the fixture to fasten and locate two

fixtures so that movement won’t happen and jointing become more conveniently, please see

figure 1 showed below:

Figure 1

Secondly, use L type Hexagon wrench to counter-clockwise rotate connection lock to the end

until lock tongue returns back, for direction please see arrow ①showed in figure 2 ,and the

next step, use Hexagon wrench clockwise rotate connection lock to the end, see arrow ②.

Figure 2

The maximum fixtures that can be jointed together is 10.

4. How to set the unit

4.1 Rear Panel

○

1 Display: Show the various menus and the selected functions

○

2 LED:

DMX On DMX input present

MASTER On Master Mode

SLAVE On Slave Mode

○

3 Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

○

4 DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal.

○

5DMX output: For DMX512 link, use 3/5-pin XLR plug cable to link the next unit.

○

6Mains input: Connect to supply mains power.

○

7Mains output: Connect to supply mains power for the next unit.

4.2 Main Function

To select any functions, press MENU button until the required one is shown on the display.

Select the function by ENTER button and the display will blink. Use DOWN and UP button to

change the mode. Once the required mode has been selected, press ENTER button to setup

or it will automatically return to the main functions without any change after idling 30

seconds. Back to the functions without any change press MENU button. The main functions

are shown below:

DMX 512 Address

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to change the DMX 512 address. Once the address has been selected, press the

ENTER button to setup or automatically exit menu mode without any change after 60 seconds.

Back to the previous functions without any change press the MENU button.

Channel Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (1 channel) or (4 channels) or (9 Channels) or

(25 channels) or (29 Channels) mode. Once selected, press the ENTER button

to setup or automatically exit menu mode without any change after 60 seconds. To go back to

the functions without any change press the MENU button

Set Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the , or mode.Once selected, press the ENTER

button to setup or automatically exit menu mode without any change after 60 seconds. To go

back to the functions without any change press the MENU button.

Show Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (Random show) or (show 1) or (Show 2) or … or

(show 8). Once selected, press the ENTER button to store or automatically exit menu

mode without any change after 60 seconds. To go back to the functions without any change

press the MENU button

Manual Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (number) or (letter). When the is selected,

press the ENTER button, then use the DOWN and UP button to select the or…or

,and press the ENTER button to store. If you select the , press the ENTER

button, use the DOWN and UP button to select the or…or , and press the

ENTER button to setup or automatically exit menu mode without any change after 60 seconds.

To go back to the functions without any change press the MENU button

Blackout Mode

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select the (blackout) or (normal). Once selected, press the ENTER

button to setup or automatically exit menu mode without any change after 60 seconds. To go

back to the functions without any change press the MENU button.

LED display

Select the , press the ENTER button and the display will blink. Use the DOWN and UP

button to select (LED display on) or (LED display off). Once selected, press the

ENTER button to setup or exit menu mode without any change after 60 seconds. Back to the

functions without any change press the MENU button again.

Display Inverse

Select the , press the ENTER button and the display will blink. Press the ENTER button

to change the display mode between (Display normal) and (Display inverse).

Back to the functions without any change press the MENU button.

Inhaltsverzeichnis

Andere ACME DJ-Equipment Handbücher

ACME

ACME LED-737 Bedienungsanleitung

ACME

ACME CHEETAH LED-GF50 Bedienungsanleitung

ACME

ACME Eventx 100 Bedienungsanleitung

ACME

ACME LED-7871 Bedienungsanleitung

ACME

ACME MACE Bedienungsanleitung

ACME

ACME Diamonds LS-1010 RGB Bedienungsanleitung

ACME

ACME LP-TS200 CW Bedienungsanleitung

ACME

ACME E-10C WW DXX Bedienungsanleitung

ACME

ACME E-10 WW DXX Bedienungsanleitung

ACME

ACME CA-DD12 II Bedienungsanleitung

ACME

ACME LED-Exercet Bedienungsanleitung

ACME

ACME LED-BL4B Bedienungsanleitung

ACME

ACME SAMBA Color Bedienungsanleitung

ACME

ACME CW-108 Bedienungsanleitung

ACME

ACME ENERGY SPOT XA-400 SPOT Bedienungsanleitung

ACME

ACME IM-5S-ELC Bedienungsanleitung

ACME

ACME LED-747-1W Bedienungsanleitung

ACME

ACME LED WAVE 100 Bedienungsanleitung

ACME

ACME iColorLed 18TC Bedienungsanleitung

ACME

ACME FARANDOLE AM-BAR Bedienungsanleitung

ACME

ACME Super Dotline Bedienungsanleitung

ACME

ACME GLORY PROFILE Bedienungsanleitung

ACME

ACME Junior Series Bedienungsanleitung

ACME

ACME CP-21TC Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung

KAM

KAM DMX Laser80 FScan Bedienungsanleitung