ACO INS-ZS Betriebsanleitung
ASSEMBLY AND PROGRAMMING MANUAL FOR THE
AUTONOMOUS INS-ZS CODE LOCK
The autonomous INS–ZS code lock is a microprocessor
device which serves the purpose of controlling one or two
outputs independently, by means of the proper code for
the given output. The outputs may control outdoor devices
e.g. an electric door strike. INS ZS has maximum 255
opening codes created on the basis of the Table of Codes
compatible with other ACO products.
1. INSTALLATION
The base of the INS ZS lock is flush mounted and fixed by means of expansion bolts. The wires are put through hole 1.
The lock is connected according to schedule placed in the further part of the manual. The enclosure is locked using the
Allen key with the size of 3, by means of 4 screws. Holes No. 2 serve the purpose of temporary installation of the lock
by means of e.g. nails, in case of placing the device in soft materials, e.g. polystyrene. Holes No. 3 facilitate the
installation in case of using the assembly foam.
2. METHOD OF OPERATION
Depending on the mode of operation, the activation of one of the two outputs consists in:
In the mode of 255 codes – selection of the code ordinal number by means of the keypad, approval of the
selection by push button (key) and entry of the proper four digit code from the attached Table of Codes.
In mode 1 to 8 – selection of the proper four digit code by means of the keypad. The first of the codes is code
No. 1 in the Table of Codes, the second code is code No. 2, etc.
According to the factory settings, all the codes activate only Output 1 (activity time of Output 2 = “0”).
When the activity time of Output 2 is other than “0”, the codes with uneven ordinal numbers (1, 3, 5,…) activate only
Output 1, and those with even ordinal numbers (2, 4, 6,…) only Output 2.
There is also a possibility to switch on the so called “Double Key” mode, which makes the control of two outputs (only in
the mode of 255 codes) possible with the use of the same code. The operation of the mode consists in selection of the
code ordinal number from the keypad, then, depending on whether we press the push button (key) once or twice, after
the proper four digit code is entered, output 1 or output 2 will switch on (output 1 – we press 1 x [key]; output 2 = we
press 2 x [key]).
The codes entered by the manufacturer are included in the attached “Table of Codes” (items from 1 to 255), and each
code can be changed (programme 2 in the setting programming function). It is also possible to set the so called code
“Shifts” known from other ACO products (among other things, doorphone control unit), which causes the addition of the
numerical value (from 1 to 998) to the code ordinal number (only for the mode of 255 codes). Owing to setting, the
same shift value and the same Table of Codes, we can reproduce the codes and exactly the same method of their
selection as in the ACO doorphone control units.
The lock has the INPUT, which causes the activation of Output 1 by shorting with the use of an optional push button.
The input is protected from continuous short circuit.
DIAGRAM OF CONNECTIONS
3. PROGRAMMING OF THE LOCK SETTINGS – nstallat on programm ng
It is possible to change the operating parameters of the lock by means of programming. The access to the programming
mode of lock settings is protected by an installer password. All the settings are saved in the read only memory and are
not subject to loss after switching off and on the power supply.
In order to enter the programming mode of the lock settings (installation programming) press push button [ key] and
enter an eight digit password [1507xxxx] – it is confirmed by a sound signal modulated upward. The first four digits of
the password [1507] are a fixed value, and the following ones [xxxx] are a four digit installer password (0000 – factory
setting). The activity time of the programming mode of the settings is limited to 10 sec., counting from the last change,
the exit from the programming mode takes place by means of push button [#].
Accord ng to the factory-sett ngs, the nstaller password s set to “0000” and after complet on of the
nstallat on, t must be changed to a d fferent one (P7 programme).
After entering the lock programming function, specify the programme number, which corresponds to the given settings.
After entering the programme number, the lock will count the appropriate (depending on the programme number)
number of short sound signals and will confirm the entry into a given programme by means of a short sound signal
modulated upward. At any moment we can interrupt the programming and exit the given programme by pressing push
button [#] – the changes will not be saved then.
The numbers of the respect ve programmes and the funct ons wh ch they perform:
1_1 – service activation of output 1 – causes activation of output 1 in accordance with the pre set parameters in
programme 5 (time, beeper, generator). After completion of this programme, the automatic exit from the programming
function occurs. In order to call out the programme, select: [key][1507xxxx][11].
1_2 – service activation of output 2 – causes activation of output 2 in accordance with the pre set parameters in
programme 6 (time, beeper, generator). After completion of this programme, the automatic exit from the programming
function occurs. In order to call the programme, select: [key][1507xxxx][12].
2 – Shift value setting (only in the mode of 255 codes). The function enables deduction or addition of shift value codes
from 1 to 998 to the code ordinal numbers, which will enable the selection of codes with ordinal numbers greater than
255 (the maximum number of codes does not change and still amounts to 255). For instance, for the negative shift
setting 500, we can select [502][[key]code No. 2 from Table of Codes] from the keypad. We can set (in programme
10), the positive or negative direction of shift, which enables the addition or deduction of the ordinal number of codes.
Owing to these settings, we can reproduce the codes and the method of their selection accurately, in the same way as
in ACO doorphone control units. In order to change the shift value, select:
[key][1507xxxx][2][shift value from 1 to 998] [key (if this is a one or two digit value)].
3 – the change in the 4 digit opening code. For instance, if we want to change code No. 9 to 4444, the following is
necessary: enter digit 3 (programme number) in the programming mode, the control unit will confirm the acceptance
with three short sound signals, and then digit 9 (code ordinal number ranging from 1 to 255), confirm with push button
[key] and enter the new code value – 4444. If the shift is set, specify the code number together with the added shift. In
order to change the code, select [key][1507xxxx][3][code ordinal number 1 255] [key] [new 4 digit code].
4 selection of the lock operating mode – method of opening by means of a code.
Mode [0] – available 255 codes (before selection of the code, it is necessary to enter its ordinal number).
Mode [1 8] – available (depending on the entered value) from 1 to 8 codes selected directly without specifying
the code ordinal number. The respective codes correspond to the codes from the table of codes with ordinal
numbers 1, 2,…., 8. Upon entering the mode, the automatic exit from the programming function will take
place. In order to change the lock operating mode, select:
[key][1507xxxx][4][y],
where [y] means the operating mode: y = [0] for the operating mode of 255 codes
y = [number from 1 to 8] for the mode from 1 to 8 codes
NOTE!!!
If Output 2 is switched off (activity time equal to zero) all the codes switch on Output 1
If Output 2 is switched on (activity time other than zero), the codes with uneven ordinal numbers switch on
Output 1, and those with even number switch on Output 2
5 – Output 1 parameter setting
The output parameters are entered as a three digit number [xyz], where the respective digits mean:
x – [0 or 1] – activation / deactivation of the sound signal (beeper) during the output activity (0 – on, 1 – off),
y – [0 or 1] – method of shorting the output to ground (0 – pulse, 1 – permanently),
z – [number from 1 to 9] output activity time from 1 to 9 seconds (opening time e.g. electrical door strike)
For instance, if the setting of the electrical door strike opening time to 3s is required (pulse controlled output), as the
sound signal is heard, enter number [003] in programme 5.
In order to change the parameters of Output 1, select [key][1507xxxx][5][xyz].
NOTE!!!
In order to control the electrical door strike, use the pulse control (y=0), and for relay control, use the permanent
control (y=1).
6 – Output 2 parameter setting
The setting is identical as for Output 1. Output 2 is switched on, setting its activity time as other than zero.
7 a change in the installer code. In order to change the installer code: enter digit 7 (programme number) in the
programming mode, the control unit will confirm the acceptance by means of seven short sound signals, and then enter
four digits of the new code. After entering the last digit, the code will be saved and the exit from the programming
function will take place. The order of procedure:
[key][1507xxxx][7][a new 4 digit installer code].
8 – limitation of the maximum number of available codes (only for the lock operating mode “0”!). In order to limit the
number of active codes, enter digit 8 in the programming mode (programme number), the control unit will confirm the
acceptance by means of eight short sound signals, and then specify the ordinal number from 1 to 255 of the last active
code (without taking into account the shift). After entering the single or double digit, confirm it by means of push button
[key], and after entering the third digit, the automatic exit from the programming function will take place. The order of
the procedure is as follows:
[key][1507xxxx][8][ordinal number of the last active code from 1 to 255] [key].
9 – entry of the number of the table of codes. The lock includes the tables of codes from number 0000 to 9999. In
order to change the number of the table of codes, enter digit 9 in the programming mode (programme number), and
then enter four digits specifying the number of the new table of codes. After entering it into the memory, the automatic
exit from programming function will take place. The order of the procedure is as follows: [ key][1507xxxx][9][4 digit
number of the table of codes].
10 – setting of the so called “Double key” mode and the shift direction. The “double key” mode enables the activation of
output 2 after specifying the same code as for exit 1, with the difference that the key push button must be pressed
twice (an active function only for the mode set to [0] in programme 4, and for the appropriate output 2 parameters set
in programme 6 – time other than “0”!). The direction of shift determines whether the shift value (set in programme 2)
is supposed to be added or deducted from the code ordinal number. The deduction is set as the factory setting. It
determines the method of code selection (an example for shift 100): we press [102][key][code No. 2 from the Table of
Codes]; the addition determines the method of code selection: we press [2][key][code No. 102 from the Table of
Codes].
In order to change the settings, enter d g t 0 (programme 10) in the programming mode, and then enter digit 1 to
switch on the “Double Key” mode or digit 0 to switch off the “Double Key” mode, or digit 2 to set the negative shift, or
digit 3 to set the positive shift. After entering it into the memory, the automatic exit from programming will occur. The
order of the procedure is as follows:
[key][1507xxxx][0][y]. where [y] means: y = [0] deactivation of the “double key” mode
y = [1] activation of the “double key” mode
y = [2] negative shift ( )
y = [3] positive shift (+)
Resett ng the lock – restorat on of the factory sett ngs or n case of fa lure:
1. We switch off power supply voltage, 2. We wait for about 10s, 3. We press the push buttons [2,5,8], 4. We
switch on power supply, and when we hear a sound signal, we release the push buttons. After this activity, all
the settings will be deleted and replaced by factory settings.
Table of codes w th the factory-set or recently entered number
Installer code “1507 0000” – a change s requ red!!!
Output 1 parameters: open ng t me 4s, beeper sw tched on, pulse-short ng
Output 2 parameters: open ng t me 0s. – nact ve output (all the codes switch on only Output 1)
Mode of 255 codes,
Act vated double key mode
Sh ft value = 0, a negat ve sh ft
Dur ng the f rst act vat on, change the nstaller code (programme 7)
6. TECHNICAL PARAMETERS
Power supply in the stand by mode – 12 V AC/DC 20mA (80mA during the opening procedure + output load)
Output load capacity for 10 s – max. 1 A
Method of output control: shorting to ground – pulses or on a permanent basis
Number of codes: preceded by the code ordinal number – max 255
or from one to eight codes selected without specifying the ordinal number
THE RULES OF STORAGE OF THE USED ELECTRICAL EQUIPMENT
It is not allowed to store the electrical equipment with other waste. It must be stored at sites intended for this purpose.
Therefore, please address the responsible institutions or companies dealing with waste recycling. – Directive
2002/96/WE dated January 27th, 2003
IU0306enVA.141
Inhaltsverzeichnis
Andere ACO Sperren Handbücher
