ACO INS-MP7 Bedienungsanleitung
OPERATING MANUAL FOR DIGITAL MONITOR INS-MP7
GENERAL INFORMATION
Digital video monitor INS-MP7 is compatible with outside stations FAMILI PV and INSPIR for multi apartment
buildings where video and audio communication is essential.
Video monitor has modern design and its front is made of glass. Hands free system eliminates usage of receiver
for conversation. The front panel is equipped with touch keypad with back lit operating icons.
INS-MP7 monitor is functional even if more monitors are connected to the same address. It has also ability to
control outside door bell, adjusts ringing and conversation volume, adjusts picture preferences, can control home
automatics, supports full privacy of conversation, camera preview and opens gate without connected conversation.
TECHNICAL PARAMETER
•LCD screen diagonal 7” (640x480)
•Front material Glass
•Mounting plate dimension 14cm x 9,2cm
•Monitor front dimension 24cm x 12cm
OPERATION
When the monitor receives a call from the outside unit the screen goes on, enables preview from camera and
rings. The icons of receiver, key and monitor pulse one by one. In order to answer the call, press the receiver. After
answering the call, voice connection will be made and the icons of receiver, key and monitor will become brighter.
Additionally icons of the volume adjustment will enlighten and control over volume will be possible with + and – icons.
Mute of conversation (dark volume icons) causes mute of the monitor's microphone. The end of conversation is made
with the receiver icon.
The monitor signalizes unanswered call with flashing monitor icon while standing by. In order to clear the
unanswered call touch the monitor icon.
Activation of e-lock is possible during conversation and standby. In order to do so, touch the key icon. Every
activation is signalized with peep tone. If the line is busy (other users are talking) it's not possible to activate the e-lock.
Activation of additional output (I/ module) is possible during the conversation with F icon.
Activation of preview is possible every time when the line is free (other users are not talking). In order to do so
touch the monitor icon. It is possible to turn on the screen and keep it on for 60 minutes – push and hold the monitor icon
for 5 seconds. Activation will be confirmed with peep tone and bright monitor icon. The preview will stay on until it is
turned off by touching the monitor icon for 5 sec or until a call is made. After 60 minutes the preview turns automatically
off. If 2nd camera is active, touching the F icon switches between cameras. During conversation switching the picture is
possible with the monitor icon.
A monitor which is in the system together with other monitors displays if the line is busy by flashing the middle
LED of volume control stripe. The line is busy when there is a conversation between outside station and other monitor.
When the line is busy, it is neither possible to turn the camera preview on nor to activate the e-lock.
If you try to enable a function while the monitor is blocked, it will sound peep tone and nothing will happen.
The monitor can open door automatically. This function allows to activate e-lock automatically after the call is made from
the outside station. It can be enabled for e.g. During office hours.
Automatic opening is activated by pressing and holding the key icon for at least 5 seconds. The action is
confirmed with 4 short peep tones and bright key icon. In order to deactivate the function repeat the same action.
After the monitor with the turned on automatic opening is called, it will sound single tone, in order to confirm activation of
the e-lock.
When the automatic opening is on, all monitor functions (except answering calls from the outside station) are
active. If you have more monitors with the same address, automatic opening has to be activated only in one of the units.
The monitor is equipped with door bell function. When it rings in stand-by mode, the monitor will ring the bell twice
and the 2nd camera picture will switch on (if there is one). During the conversation the bell will ring only once, it will not
cancel the conversation and it will not switch the other camera on.
CONFIGURATION
Brightness, saturation and volume can be adjusted in the monitor. With + and – icons you can control ringing
volume in the stand-by. The monitor will sound the tone of chosen volume and it will await for further adjustment with +
and -. Because of the fact that the tone is generated by the outside station it can be different. If the parameters are not
changed within 5 seconds, the monitor will save the adjusted ones.
Picture adjustment is possible only when the screen is on in stand-by (the monitor icon). After touching the + or –
icons the brightness will show up and you can change it with + and -. After touching the monitor icon you will be able to
adjust the saturation. Another touch of the monitor will switch off the adjustment menu.
Attention! If the front of the monitor is damaged, its further use might cause injuries.
STORAGE OF USED ELECTRICAL EQUIPMENT
Used electrical equipment may not be stored together with other waste. Store it at sites intended for this purpose. For this reason, address the
responsible institutions or companies dealing with waste recycling. - Directive 2 2/96/EC/ dated January 27th,
Manufacturer: AC , 62-002 Suchy Las, Diamentowa 7, tel/fax 61 843 93 71 www.aco.com.pl/en
IU 3 7enVB.1514
Inhaltsverzeichnis
Andere ACO Monitor Handbücher
