ACS WTAU-100 Bedienungsanleitung

Technical manual BA 0314

Signal converter

WTAU – 100 / 120 / 200 / 220

Isolation amplifier Pt100 – active

for galvanic isolation, conversion and

adjustment of a Pt100 temperature signal

Input signals Pt100 in 2- or 3-wire-technology

 Zero value –100°C...+35°C

 Measuring range 25K...660K

Output signals

 Direct voltage 0…10V / 2…10V – simultaneous outputs

 Direct current 0…20mA / 4…20mA - simultaneous outputs

Signal adjustment of zero value and amplification – optional

Single or double channel version – optional

Space saving safe isolation with 4kV~

Wide range power supply from 20 to 253V AC and DC

L a u t e r b a c h s t r . 5 7 – 8 4 3 0 7 E g g e n f e l d e n – G e r m a n y

T e l : + 4 9 8 7 2 1 / 9 6 6 8 - 0 – F a x : + 4 9 8 7 2 1 / 9 6 6 8 - 30

i n f o @ a c s - c o n t r o l s y s t e m . d e – w w w . a c s - c o n t r o l s y s t e m . d e

WTAU –100 / 120 / 200 / 220

page 2 of 8

Index

Order code .................................................................................................................... 2

Application .................................................................................................................... 3

Function ........................................................................................................................ 3

Safety notes .................................................................................................................. 4

Installation ..................................................................................................................... 4

Maintenance ................................................................................................................. 4

Repair ............................................................................................................................ 4

Electrical connection ................................................................................................ 5 / 6

Operation and display elements ................................................................................... 7

Technical data ............................................................................................................... 8

Order code

WTAU – 100 – U0 Version single channel device, adjustable

WTAU – 120 – AB – U0 Version single channel device, fix adjusted

temperature range

code no. A

output 1

code no. B

0°C…+50°C

0…10V

0°C…+100°C

0…20mA

0°C…+150°C

4…20mA

0°C…+200°C

special range

0°C...+250°C

0°C…+300°C

0°C…+400°C

0°C…+500°C

0°C…+600°C

output 2

code no. C

-40°C...+60°C

0…10V

-50°C...+100°C

0…20mA

-100°C...+50°C

4…20mA

special range

WTAU – 220 – ABC – U0 Version double channel device, fix adjusted

WTAU – 200 – U0 Version double channel device, adjustable

WTAU –

100 – U0

WTAU –

120 – U0

WTAU –

200 – U0

WTAU –

220 – U0

Fix adjusted version

Adjustable version

Single channel version

Double channel version

WTAU –100 / 120 / 200 / 220

page 3 of 8

Application

The active isolation amplifier of the series WTAU is used to linearize Pt100 temperature signals, to convert it

into one resp. two galvanic isolated electrical standard signals or to adjust the signals in the zero value and/or

end value resp. amplification.

A galvanic isolation is sometimes the only possibility at error generating ground loops, unwished signal

overlapping and potential problems.

Thus, a current flow between more signal current circuits that distort the signal is avoided.

The free configurable resp. fix signal conversion, dependent on version, allows the flexible adaption of the Pt100

temperature signal to different systems, e.g. to the standard signal input of a SPS control.

The adjustable version is suitable, if sections, e.g. +10°C...+40°C of a standard temperature signal 0°C...+50°C

should be amplified to a complete standard signal e.g. 4...20mA or for zero value adjustment e.g. because of

temperature losses caused by heat transfer.

At the versions WTAU – 200 – U0 / WTAU – 220 – U0 the Pt100 temperature signal is converted in parallel into

two electrical standard signal. Thus the Pt100 temperature signal can be doubled, to use it in two separated

evaluation circuits.

Function

Measuring principle

Version WTAU – 100 – U0 / WTAU – 200 – U0 – adjustable version

The connected resistance proportional electrical Pt100 voltage signal is measured by the evaluation circuit,

linearized, adjusted according to the front-sided trimmer and transmitted galvanically isolated to the

simultaneous output signals 0...10V and 0...20mA or 2...10V and 4...20mA according to the settings of the

internal configuration switches.

The respective current resp. voltage signals at the output can be used simultaneous. Therefore there are

simultaneous 2 output signals at the single channel versions WTAU – 100 – U0 and simultaneous 4 output

signals at the double channel version WTAU – 200 – U0 are available.

Examples:

 WTAU – 100 – U0 Input signal 0°C..+100°C is converted to output signal 0...10V / 0...20mA

 WTAU – 100 – U0 Input signal 0°C..+50°C is converted to output signal 2...10V / 4...20mA

 WTAU – 200 – U0 Input signal 0°C..+50°C is converted to output signal 1 0...10V / 0...20mA

output signal 2 2...10V / 4...20mA

Version WTAU – 120 – U0 / WTAU – 220 – U0 – fix adjusted version

The connected resistance proportional electrical Pt100 voltage signal is measured by the evaluation circuit,

linearized and transmitted galvanically isolated to the to the output signal 0...10V or 0...20mA or 4...20mA.

At the version WTAU – 220 – U0 the Pt100 input signal is transmitted simultaneously to the both output

channels.

Examples:

 WTAU – 120 – U0 Input signal 0°C..+100°C is converted to output signal 0...10V

 WTAU – 220 – U0 Input signal 0°C..+50°C is converted to output signal 1 0...10V

output signal 2 0...20mA

WTAU –100 / 120 / 200 / 220

page 4 of 8

Safety notes

Each person that is engaged with inauguration and operation of this device, must have read and

understood this technical manual and especially the safety notes.

Installation, electrical connection, inauguration and operation of the device must be made by a qualified

employee according to the informations in this technical manual and the relevant standards and rules.

The device may only be used within the permitted operation limits that are listed in this technical manual.

Every use besides these limits as agreed can lead to serious dangers.

The device meets the legal requirements of all relevant EC directives.

Installation notes

The device is conceived for vertical installation on a standard fastening rail acc. to DIN EN 60715 TH 35-7,5

resp. TH 35-15.

DIN EN 60715 TH 35-7,5

DIN EN 60715 TH 35-15

The device must be installed protected against dust and humidity, e.g. in control stations or in a suitable

protection housing with a minimum protection classification IP55 acc. to DIN EN 60529.

The devices must be installed wheather and stroke protected, ideally at places without direct solar radiation.

This is especially important in warm climatic regions.

Maintenance

The device is free of maintenance.

Repair

A repair may only be carried out by the manufacturer. When sending back the device, add a note with the

description of the error and the application.

WTAU –100 / 120 / 200 / 220

page 5 of 8

Electrical connection

The electrical connection of the device must be carried out according to the respective country specific

standards. Incorrect installation or adjustment could cause applicationally conditioned risks.

Power supply input, measuring input and signal output channels are safe galvanically isolated from each other.

This is also valid for both signal output channels among each other.

Connection of the Pt100 – measuring input

For the two or three-wire connection cable between the isolation amplifier and the Pt100 a standard installation

cable or multi-wire cable for measuring intends with a maximum of 25  per wire can be used.

Pt100 in 2- or 3-wire-measurement can be connected.

At a 2-wire-measurement the terminals 1 and 2 must be connected by a wire link.

A 4-wire-measurement of the Pt100 is not possible. When connecting a 4-wire Pt100 this must be proceeded in

3-wire-measurement, whereas the not used fourth wire may not be connected..

The use of a shielded signal cable is recommended, if strong electromagnetic influences could happens, e.g.

due to machines or radio equipment. In that case the shielding of the cable should be connected to earth only at

the side of the Pt100.

The signal cable should be installed separated from power leading wires.

Terminal occupation

Connection scheme

WTAU –100 / 120 / 200 / 220

page 6 of 8

Electrical connection

Connection of the output

For the two-wire connection cable between the isolation amplifier and the connected devices a standard

installation cable or multi-wire cable for measuring intends with a maximum of 25  per wire can be used.

The use of a shielded signal cable is recommended, if strong electromagnetic influences could happens, e.g.

due to machines or radio equipment. In that case the shielding of the cable should be connected to earth only at

the side of the connected device. When connecting a SPS input stage there must be paid attention that mostly

the signal circuit must be connected to earth by connection the minus terminal with measuring earth.

The signal cable should be installed separated from power leading wires.

For inauguration it is suggested, to deactivate all connected control devices, to avoid unwanted control reactions.

Connection of the power supply voltage

Due to the integrated wide range power supply, for connection to supply voltages from 20...253V AC / DC, the

isolation amplifier is suitable for using in all common energy supply networks.

The connection is reverse polarity protected.

A fuse is integrated internally at the power supply circuit. Due to this the installation of a fine protection is not

necessary.

Terminal occupation

Connection scheme

WTAU –100 / 120 / 200 / 220

page 7 of 8

Channel 2

Trimmer for zero and

end value adjustment

only at version

WTAU – 200

Function indicator

1 LED for indication of

ready status

Channel 1

Trimmer for zero and

end value adjustment

only at version

WTAU – 100 / 200

Configuration switch

inside the housing

only at versions

WTAU – 100 / 200

Operation and display elements

Function indicator

 ON  green LED  ready status, power supply voltage on

Trimmer

For adjustment of zero and end value per channel. Only available at versions WTAU – 100 / 200.

At the Pt100 – isolation amplifier WTAU – 200 – U0 both output signals (output 1 and output 2) are changed uniform by the

configuration switches and by the trimmer channel 1.

The output 2 can be additionally separately changed in the zero value by  3% and in the end value by  6% by the further

trimmer at the front side (channel 2).

For an accurate results the adjustment zero value – end value must be proceeded repeatedly with connected signal,

because zero and end value adjustment effects each other.

Configuration switches

The configuration of the input and output signal ranges is made per dip switches inside the housing.

Dangerous voltage

Ensure a safe switching off the supply voltage when opening the housing

For configuration release the upper housing part at top and bottom side behind the terminals by using a screwdriver and pull

it out of the housing. Drop-in pin's avoid a complete pulling out. Following the respective dip switches can be set according to

the desired functions to ON or OFF.

The switch S3 of switcher block S3 must be set to position ON. The position of all other not described switches are without

importance.

Input signal range zero value switcher block SB1

Switch 2 (SB1)  zero value

switch

switching state ON

switching state OFF

zero value 0°C

zero value –50°C

Input signal range measuring range switcher block SB2

Switch 1, 2, 3, 4, 5, 6 (SB2)  measuring range

measuring range

OFF

50 Kelvin

OFF

100 Kelvin

OFF

150 Kelvin

OFF

200 Kelvin

OFF

300 Kelvin

OFF

500 Kelvin

Output signal range channel 1 switcher block SB1

Switch 4 (SB1)  signal range

switch

switching state ON

switching state OFF

0...10V / 0...20mA

2...10V / 4...20mA

Output signal range channel 2 switcher block SB3

Switch 4 (SB3)  signal range

switch

switching state ON

switching state OFF

0...10V / 0...20mA

2...10V / 4...20mA

WTAU –100 / 120 / 200 / 220

page 8 of 8

Technical data

Auxiliary power supply

Permitted supply voltage: 20 V to 253 V AC / DC 48...62 Hz, reverse polarity protected

Power consumption:  3 VA / 2 W (WTAU –100 / 120) resp.

 6 VA / 3 W (WTAU – 200 / 220)

Overvoltage category: II acc. to DIN EN 61010-1

Protection classification: II double or reinforced insulation

Isolation voltage: 4kV~ auxiliary power to signal inputs to signal outputs

Galvanic isolation: All supply, input and output channels among each other as well as both

output channels from each other are safe galvanically isolated.

Signal input

Temperature resistor Pt100: 3-wire- / 2-wire-measurement, temperature linear, current 2 x 0,680mA  20µA

Measuring signal range: -100°C...+660°C, dependent on settings resp. configuration

Wire resistance:  40  per wire

Signal output (1x resp. 2x available, depends on version)

Direct voltage: 0…10 V / 2...10 V, max. 15V  5%, overload and short circuit protected

Permitted load direct voltage:

 WTAU –100 / 120 RL  1250 at 10V / RL  2000 at 10V (at simultaneous output Iout with 20mA)

 WTAU – 200 / 220 RL  3333 at 10V / RL  6666 at 10V (at simultaneous output Iout with 20mA)

Direct current: 0…20mA / 4…20mA, max. 25mA  5%

Permitted load direct current:

 WTAU –100 / 120 RL  880 at 20mA / RL  680 at 20mA (at simultaneous output Uout with 5mA)

 WTAU – 200 / 220 RL  570 at 20mA / RL  530 at 20mA (at simultaneous output Uout with 1,5mA)

Adjustment range zero value: –100...+35°C depends on setting configuration switch zero value

Adjustment range measuring range 25...660K depends on setting configuration switch measuring range

Adjustment range zero output 2:  3% of respective nominal measuring range

Adjustment range - range output 2:  6% of respective nominal measuring range

Limit value deviation:  0,1% of factory calibrated measuring range (delivery setting)

Range changing deviation:   5% of respective nominal measuring range

Characteristic deviation:  0,1% of respective nominal measuring range

 0,2% at range 50K of respective nominal measuring range

Temperature deviation:  0,05% / 10 K of respective nominal measuring range

Long term deviation:  0,1% of respective nominal measuring range / year

Influence output load:  0,05% of respective nominal measuring range

Influence auxiliary power:  0,005%/10V at range 500K of respective nominal measuring range

 0,06%/10V at range 50K of respective nominal measuring range

Error supervision: Output signal  20mA/10V at wire break

Output signal 0mA/0V at short circuit of terminals 1/3 resp. 2/3

Measurement in 2-wire-technology at short circuit of terminals 1/2

Materials

Connection housing: PA – polyamide

Terminal housing: PA – polyamide

Sticker: PE – polyester

Connection terminals

Number: 3 terminal blocks with each 4 terminals, everlasting screws

Connection cross-section: maximum 1 x 2,5 mm or 2 x 1,5 mm

Housing style

Housing: Series installation housing, 22,5mm wide

Weight: 100 g

Environmental conditions

Environmental temperature: Single installation – 40°C...+70°C

Series installation – 40°C...+60°C

Climatic classification: 3K3 resp. 3M2 DIN EN 60721-3-3

Protection classification: IP20 DIN EN 60529

EM – compatibility: emission DIN EN 61326-1 operation device class B

immunity DIN EN 61326-1 industrial range

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACS Verstärker Handbücher

ACS

ACS TVA-080 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung