ACTi ACM-5811 series Bedienungsanleitung
IP CCD D/N PoE Box Camera
ACM-5811 series
Ver. 120312
Quick Installation Guide
0-1
0Getting Started
1.1 PACKAGE CONTENTS
ACM-5811
Product CD Terminal Blocks for Power & DI/O
Warranty Card Accessory
1
0-1
1.2 PHYSICAL DESCRIPTION
1. DC Iris
DC Iris Lens Control Port
2. Analog Video Output
The IP CCD D/N PoE Box Camera supports one channel analog
video output.
3. Ethernet Port
The IP CCD D/N PoE Box Camera connects to the Ethernet via a
standard RJ45 connector. This camera can automatically detect
the best network speed when connected to other
auto-negotiation(NWAY) supported devices.
(10Base-T/100Base-TX Ethernet).
4. Reset Button
Step 1: Switch off IP device by disconnecting the power cable
0-2
Step 2: Press and continue to hold the Reset Button with a
pointed object. Reconnect the power cable while still holding the
reset button.
Step 3: Keep the reset button depressed for at least 6 seconds
before releasing it. The unit will then start up with factory default
settings.
5. The I/O Terminal Connector
Used in applications like motion detection, event triggering, time
lapse recording, alarm notifications, etc., the I/O terminal
connector provides the interface to:
•1 transistor output - For connecting external devices such as
relays and LEDs. Connected devices can be activated by Output
buttons on the Live View page or by an Event Type. The output
will show as active (in Event Configuration > Port Status) if the
alarm device is activated.
•1 digital input - An alarm input for connecting devices that can toggle
between an open and closed circuit, for example: PIRs,
door/window contacts, glass break detectors, etc. When a signal is
received, the device state changes and the input becomes active
(shown under Event Configuration > Port Status).
•Auxiliary power and GND
Pin 1
GND
Ground
Description
Pin 2
Auxiliary DC
Power input
(not to power
this camera)
Electrically connected in parallel with the con-
nector for the power supply, this pin provides an
auxiliary connector for mains power to the unit.
This pin can also be used to power auxiliary
equipment, with a maximum current of 100mA.
Voltage: 12V DC,
Max: 1.2W
Pin 3
Digital Input
Connect to GND to activate, or leave floating (or
unconnected) to deactivate.
Must not be exposed to
voltages greater than 30V
DC.
Pin 4
Transistor
Output
Uses an open-collector NPN transistor with the
emitter connected to the GND pin. If used with an
external relay, a diode must be connected in
parallel with the load, for protection against
Max load = <100mA
Max voltage = 24V DC
(to the transistor)
0-3
transient voltages.
The I/O terminal pins are numbered left to right, as shown below.
Connect input/output devices to the camera as follows:
1. Attach the cables for the device securely to the supplied green
connector block.
2. Once the cables are connected, push the connector block into the
terminal connector (also green) on the camera.
1
2
3
FUSE 1A
NPN
DC TO DC
DI
DO
3.3V
DC POWER
GND 1
2
3
4
CONVERTER
EARTH GND
DO
DI
RELAY
SW
DIODE
DEVICE
-
+
POWER INPUT
CAMERA
6. Power Input
Connect the power adaptor here if your power input is DC12V.
7. Audio Input / Output
The IP device supports audio input and output with earphone jack
0-4
0-1
1.3 BASIC CONNECTIONS
Follow the procedures below to connect the IP device to the respective
apparatuses.
1. Connect an analog monitor to IP device video out (BNC Connector)
2. Connect the power adaptor to IP device
3. Connect IP CCD D/N PoE Box Camera’s ethernet port to an Ethernet
(RJ45 connectors). If your IP CCD D/N PoE Box Camera supports Power
Over Ethernet (PoE), you may connect it directly to a PoE supported
switch, a PoE injector connected to a switch or other Power Source
Equipments(PSE)
4. Connect a PC to the Ethernet hub (RJ45 connectors)
NOTE: For more detailed explanations, we provide a support
package that clarifies PoE related concepts for you. Please visit our
web site and download the support document TS-00040.
1-2
1Quick Tour
This section guides you with a quick tour on this IP device.
2.1 Configure this IP Device
2.1.1 Make sure network environment
Default IP of this IP device is 192.168.0.100. Please make sure this IP device and
your PC are on the same network segment before running the installation.
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254 except 100, which is
used by the IP device. Please also
make sure that no two equipments
use the same IP address in the
same network..)
Inhaltsverzeichnis
Andere ACTi IP-Kamera Handbücher
ACTi
ACTi CAM-5100 Bedienungsanleitung
ACTi
ACTi TCM-5311 Gebrauchsanweisung
ACTi
ACTi CAM-5100M Bedienungsanleitung
ACTi
ACTi ACM-4000 Gebrauchsanweisung
ACTi
ACTi CAM-5200S Bedienungsanleitung
ACTi
ACTi TCM-4101 Gebrauchsanweisung
ACTi
ACTi TCM-3111 Bedienungsanleitung
ACTi
ACTi CAM-6200 Handbuch
ACTi
ACTi Indoor Dome Series E610 Bedienungsanleitung
ACTi
ACTi ACM-1310 series Bedienungsanleitung
ACTi
ACTi CAM-5120 Bedienungsanleitung
ACTi
ACTi CAM-5100H Bedienungsanleitung
ACTi
ACTi TCM-1511 Gebrauchsanweisung
ACTi
ACTi TCM-4101 Gebrauchsanweisung
ACTi
ACTi KCM-5211 Bedienungsanleitung
ACTi
ACTi ACM-1432 Gebrauchsanweisung
ACTi
ACTi ACM-8511 Bedienungsanleitung
ACTi
ACTi CAM-7300 series Bedienungsanleitung
ACTi
ACTi ACM-4200 series Bedienungsanleitung
ACTi
ACTi TCM-5311 Bedienungsanleitung
