ACTi ACM-1011 Series Bedienungsanleitung
IP IR D/N PoE Bullet Camera
(with DC 12V / PoE)
ACM-1011 series
Ver. 081208
Quick Installation Guide
0-1
0Getting Started
1.1 PACKAGE CONTENTS
ACM-1011 series Power Adaptor (Option)
(DC12V / PoE)
The bracket is not included
Product CD Terminal Block for Power
Warranty Card
1
0-2
1.2 PHYSICAL DESCRIPTION
1. Audio Input / Output
The IP IR D/N PoE Bullet Camera supports audio input and
output with earphone jack
2. Power Input
If your power input is DC12V. Please follow the description on
the connector to connect to power.
3. Ethernet Port
The IP IR D/N PoE Bullet Camera connects to the Ethernet via a
standard RJ45 connector. Supporting NWAY, this IP IR D/N PoE
Bullet Camera can auto detect the speed of local network segment
(10Base-T/100Base-TX Ethernet).
4. Reset Button
Step 1: Switch off IP IR D/N PoE Bullet Camera by
disconnecting the power cable
Step 2: Press and continue to hold the Reset Button. Reconnect
PIN
NAME
DESCRIPTION
1
12V
DC Power Input
2
GND
Ground Pin
0-3
the power cable while continuing to hold the reset button.
Step 3: Keep holding the reset button depressed for a while,
release the reset button. The unit will start up with factory default
settings.
5. Power LED Indicator
The LED indicator lights up one time upon power up. It will
lights up again when this IP IR D/N PoE Bullet Camera is fully
booted up.
0-4
1.3 BASIC CONNECTIONS
Follow the procedures below to connect the IP IR D/N PoE Bullet Camera
to the respective apparatuses.
1. Connect the power adaptor to IP IR D/N PoE Bullet Camera
2. Connect IP IR D/N PoE Bullet Camera’s ethernet port to an Ethernet
(RJ45 connectors). If your IP IR D/N PoE Bullet Camera has PoE built-in,
you can regard it as a PD and connect it directly to a PSE device like PoE
switch.
3. Connect a PC to the Ethernet hub (RJ45 connectors)
1
NOTE: You may find a support package for help you getting familiar
with PoE. Please visit our web site, and get the support document
TS-00040.
0-5
1.4 Installation Procedure
1.4.1 Install the camera onto bracket
1.4.2 Rotate camera box counter-clockwise to remove camera
cover
0-6
1.4.3 Adjust the focus / zoom
- Zoom adjust lever
- Focus adjust lever
1-7
1Quick Tour
This section guides you with a quick tour on this IP IR D/N PoE Bullet Camera.
2.1 Configure this IP IR D/N PoE Bullet Camera
2.1.1 Make sure network environment
Default IP of this IP IR D/N PoE Bullet Camera is 192.168.0.100. Please make sure
this IP IR D/N PoE Bullet Camera and your PC are on the same network segment
before running the installation.
2.1.2 Open Internal Explorer with IP address
2
Please set the settings as below.
IP address: 192.168. 0.xxx
Subnet mask: 255.255.255. 0
(NOTE: xxx should be a number
from 1 to 254, but 100 is
excepted.)
1-8
NOTE: If your web browser is earlier than IE6, then download IE6 is
recommended.
NOTE: This IP IR D/N PoE Bullet Camera default IP address is set to
192.168.0.100
2.1.3 Login with default administrator’s account & password
NOTE: Default administrator account is set to Admin, password is set to
123456, and click button.
2.1.4 Preview the video
Inhaltsverzeichnis
Andere ACTi Sicherheitskamera Handbücher
ACTi
ACTi TCM-7411 Gebrauchsanweisung
ACTi
ACTi ACM-3300 Gebrauchsanweisung
ACTi
ACTi B41 Bedienungsanleitung
ACTi
ACTi E911 Bedienungsanleitung
ACTi
ACTi E33 Bedienungsanleitung
ACTi
ACTi CAM-6110 Bedienungsanleitung
ACTi
ACTi Z76 Bedienungsanleitung
ACTi
ACTi KCM-8211 Bedienungsanleitung
ACTi
ACTi E31 Bedienungsanleitung
ACTi
ACTi B61 Bedienungsanleitung
ACTi
ACTi B81 Bedienungsanleitung
ACTi
ACTi Z98 Bedienungsanleitung
ACTi
ACTi KCM-7311 Bedienungsanleitung
ACTi
ACTi E918 Bedienungsanleitung
ACTi
ACTi KCM-8211 Bedienungsanleitung
ACTi
ACTi A811 Bedienungsanleitung
ACTi
ACTi ACM-7411 Series Bedienungsanleitung
ACTi
ACTi Q92 Bedienungsanleitung
ACTi
ACTi A711 Bedienungsanleitung
ACTi
ACTi KCM-3911 Bedienungsanleitung
