ACTi CAM-6600 Series Bedienungsanleitung

IP Outdoor High Speed Dome

CAM-6600 series

Ver. 070307

Quick Installation Guide

1 Getting Started

1.1 PACKAGE CONTENTS

CAM-6600 series Warranty Card

SoftwareCD Power&A/VCable

LAN/WAN Cable Alarm Cable

5.4” Transparent Cover Power Adaptor (Option)

Lubricant Screws

1.2 PHYSICAL DESCRIPTION

Outdoor High Speed Dome Bottom

1. Reset Button

Step 1: Switch off IP device by disconnecting the power cable

Step 2: Press and continue to hold the Reset Button. Reconnect the power cable

while continuing to hold the reset button.

Step 3: Keep holding the reset button depressed around 6 seconds, release the

reset button. The unit will start up with factory default settings.

2. Communication Switch Setting

The table below shows the function of each pin within the Communication

Switch.

Communication Switch Pin 1

Pin 2 RS-232 Setting (Reserved)

Pin 3 Termination

Pin 4 Line Lock

Pin 5 System Initialization (for

upgrade)

Pin 6 Reserved

RS-232 is reserved for internal use only; The Pin 3 and Pin 4, they are used for

termination and Link Lock adjustment respectively. The Pin 5 is mainly used for

return to factory default of camera setting.

3. Dome ID Setting

Use the switch to change your speed dome ID by turning the arrow to the desired

number respectively. For instance, if the speed dome ID is 123, the ID switch

should be set as below:

centesimal decimal single digit

NOTE: No two speed domes should be given the same ID, or

communication conflict may occur.

NOTE: The number “0” should locate upwards as shown in

above diagram for correct switch definition.

4. Dome Control Protocol

Protocol is a specific set of rules, procdures used for data communications.

Basing on the protocol of your management software that you are going to use.

Use the switch to set your dome control protocol and the baud rate. Refer to

table below and turn the arrow to choose a protocol for your speed dome.

Switch No. Protocol Baud Rate

01 Pelco D 2400

02 Pelco P 4800

07 DSCP 9600

11 Pelco D 4800

12 Pelco D 9600

13 Pelco P 2400

14 Pelco P 9600

Select protocol: Pelco D, with switch no. 01 and baud rate 2400, for instance, the

ID switch should be set as below:

decimal single digit

5. 16 Pin Connector for LAN/WAN

The LAN/WAN cable (shown as the figure below) is shipped with IP high

speed dome. Please find it in the accessory bag.

6. 22 Pin Connector

A 50cm data cable (shown as the figure below) is shipped with IP high speed

dome. Please find it in the accessory bag.

The 22-pin connector definition is listed as below.

No. Pin Cable

1 AC 24-1/DC GND 20AWG

2 Alarm Pin (Not wired)

3 AC 24-2/DC 12(+) 20AWG

4 Alarm Pin (Not wired)

5 FG 20AWG

6 Alarm Pin (Not wired)

7 T+

8 R-

9 T-

10 R+

24AWG

11~20 Alarm Pin (Not wired)

21 VGND

22 Video 24AWG

Power Input

NOTE: For alarm connection, please refer to section 1.3

Cable Wiring.

PIN NAME DESCRIPTION

Wiring Indication

of Power Adapter

1 AC24V AC 24V of Power Input Brown

2 E-GND E-Ground Pin of Power Input Green/Yellow

3 AC24V AC 24V of Power Input Blue

Power Adpater

1.3 Cable Wiring

Cable Wiring and Connection

Users may need to do cable wiring when connecting alarm input and output devices.

The table follows will illustrate the way to wire cords into the connector housing

(shown in the figures below).

Insert the terminal into the pin

holes on the connector

housing, with the hook

outward, as indicated in the

figure.

To unlock the terminal, press

the hook, as indicated in the

figure, with a proper tool and

pull it out gently.

Alarm Cable Wiring

The alarm pins are serviceable for connecting alarm input and output devices, such

as alarm sensors, sirens or flashing lights with the surveillance system. The table

shown as follows lists the definition of alarm pins on the 22-pin connector.

Pin Definition

2 ALM NC

4 ALM NO

6 ALM COM

11 ISOG

12 ALM-1

13 ALM-3

14 ALM-2

15 ALM-4

16 ALM-5

17 ALM-6

18 ALM-7

19 ALM-8

20 ALM GND

1.4 IP High Speed Dome Setups

Before installing or connecting the speed dome camera, please refer to this section and complete

preparation, switch setting and communication switch settings.

1.4.1: Prepartions for Dome Setups

The section will illustrate the speed dome housing installation procedure of the outdoor speed dome

equipped with sunshield. Please follow the steps below to complete speed dome housing installation.

STEP 1

Unpack the dome package and take

out the dome body.

STEP 2

Rotate the top holder and take it

off from the dome body.

STEP 3

Set the dome on a flat table to keep

it stable and then remove the

protective cover and PE cloth.

STEP 4

Attach the dome cover to the dome

body. Before doing that, apply

some lubricant on the dome

cover’s water-proof rubber to make

the installation process smoother.

Note that the tiny protrusion on the

dome cover must align with one of

the four holes on the dome body.

STEP 5

Assemble the dome cover to the

dome body by pressing the cover

gently downward to the dome body

with two hands on the side of the

cover.

DO NOT press the cover as shown

in the figure; this might cause

damage to the dome body.

STEP 6

Screw the dome cover and body

together.

1.4.2: Dome Setups

Before connecting the speed dome camera to other devices of CCTV system, please complete the

speed dome ID and communication switch settings. These switches are located on the bottom of the

speed dome camera (refer to section 1.2 Physical Description).

1.5 Basic Connections

Follow the procedures below to connect the IP high speed dome to the respective apparatuses.

Andere Handbücher für CAM-6600 Series

Inhaltsverzeichnis

Andere ACTi Sicherheitskamera Handbücher

ACTi

ACTi E44 Bedienungsanleitung

ACTi

ACTi A21 Bedienungsanleitung

ACTi

ACTi A310 Bedienungsanleitung

ACTi

ACTi ACM-3511 Bedienungsanleitung

ACTi

ACTi E12 Bedienungsanleitung

ACTi

ACTi Covert Series Bedienungsanleitung

ACTi

ACTi B922 Bedienungsanleitung

ACTi

ACTi Z710 Bedienungsanleitung

ACTi

ACTi VMGB-351 Bedienungsanleitung

ACTi

ACTi ACM-3210 Series Gebrauchsanweisung

ACTi

ACTi Q92 Bedienungsanleitung

ACTi

ACTi PMON-1001 Bedienungsanleitung

ACTi

ACTi A3 Series Bedienungsanleitung

ACTi

ACTi KCM-5211E Gebrauchsanweisung

ACTi

ACTi B4 Series Bedienungsanleitung

ACTi

ACTi Z98 Bedienungsanleitung

ACTi

ACTi CAM-6110 Bedienungsanleitung

ACTi

ACTi ACM-360 Series Gebrauchsanweisung

ACTi

ACTi A956 Bedienungsanleitung

ACTi

ACTi KCM-7211 Gebrauchsanweisung

ACTi

ACTi ACM-4200 series Bedienungsanleitung

ACTi

ACTi D9 Series Bedienungsanleitung

ACTi

ACTi ACM-1431 Bedienungsanleitung

ACTi

ACTi TCM-5111 Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung