ACU-RITE SENC 150 Bedienungsanleitung

SENC 150

READING HEAD REPLACEMENT INSTRUCTIONS

SENC 150 Reading Head Replacement Instructions

Table of Contents /Warnings

Page

1Introduction / Supplied items ........................................ 4

2Preparing the removal ................................................... 5

3Removing the encoder ................................................. 6

4Removing the reading head .......................................... 7

5Cleaning the scale ......................................................... 7

6Inserting the reading head ............................................ 8

7Preparing the remounting ............................................. 9

8Remounting the encoder assembly ............................ 10

9Checking the mounting ............................................... 11

SENC 150 Reading Head Replacement Instructions1 Introduction / Supplied items

SENC 150

REFERENCEMANUAL

SENC 150

REFERENCEMANUAL

Before you begin:

Read the instructions completely before replacing the reading

head.

Please ensure that no further damage occurs while

removing the reading head.

Note: Mounting and commissioning is to be conducted

by a qualified specialist under compliance with local safety

regulations. Do not engage or disengage any connections

while under power. The system must be disconnected from

power.

ASENC 150 reading head

BReference manual

CDisposal notice

DHead replacement hardware kit

Contents

Contents key

SENC 150 Reading Head Replacement Instructions

2 Preparing the removal

Remove all cable ties or retaining clips.

Disconnect the reading head cable from the readout.

Slide brackets against

reading head snap into place. Insert brackets at 45°

and twist to lock in scale grove.

Preparing the removal Installing alignment brackets

Attach the alignment brackets (included in head replacement

hardwarekit)byinserting thetop earsinto thebottom grooves

in the scale case.

Numbers and letters on reading head casting and alignment

brackets correspond when assembled.

SENC 150 Reading Head Replacement Instructions

Center

support

M6 x 25 mm

(1/4”-20 x 3/4” BHCS)

M6 flat washer

Removing the reading head screws Removing the end hole or set screws

Removing the end cap(s)Removing the center support

M4 x 25 mm SHCS low head

(8-32 x 5/8” SHCS low head)

(8-32 x 3/4” SHCS low head)

Do not remove any mounting brackets unless it is completely

unavoidable.

Remove the two reading head mounting fasteners.

Remove the end hole mounting fasteners unless encoder is

spar mounted, then loosen the set screws and remove the

scale case from the spar.

The reading head can be removed from either end.The view

shown is for illustration only. Use caution not to lose the

spring clip during the end cap removal.

Remove the fastener from the center support if one is

present.

M6 x 25 mm

(1/4”-20 x 3/4” BHCS)

M6 flat washer

set screws

spring clip

3 Removing the encoder

SENC 150 Reading Head Replacement Instructions

Removing the reading head Cleaning the glass scale

Remove the alignment brackets.

Gently slide the reading head out of the end of the scale case.

Place the defective reading head in a safe location.

Saturate a clean cotton swab or lint-free cloth with alcohol.

Clean the glass scale by wiping the surface and edge.

Wipe until no residue is found on the swab or cloth.

Do not scratch the inside of the scale.

Lip seals may be removed for glass cleaning if desired.

Gently pull seals out through the end of the scale case.

Reinsertthelip sealsinto theend ofthe scalecase, andgently

pull them through the extrusion. Center the seals in the case.

Runaplasticpinbetweenthelipsealsto resetthemintoposition.

Slide brackets away from

reading head and cable.

Twist brackets 45° to remove.

4 Removing the reading head

5 Cleaning the scale

SENC 150 Reading Head Replacement Instructions

Insertion tool

Aligning of insertion tool and scale

Inserting the tool

Inserting the reading head

Remove tape keeping the reading head contained within the

insertion tool.

Note the orientation of the reading head to the insertion tool.

Theinsertiontool and thereading headhavetobe in alignment. Slide the reading head gently to the center of the scale

case and remove the insertion tool.

Push the tool into the end of the scale case until it is stopped

by the blade touching the glass.

Gently slide the reading head assembly onto the scale glass

from the tool. Do not force the reading head; it will glide

smoothly.

If resistance is felt, ensure that the tool is inserted correctly

into the end of the encoder case.

6 Inserting the reading head

insertion tool

glass scale

SENC 150 Reading Head Replacement Instructions

Installing end cap(s)

Slide brackets against

reading head snap into place. Insert brackets at 45°

and twist to lock in scale grove.

Installing alignment brackets

Attach the alignment brackets provided by inserting the top

ears into the bottom grooves in the scale case.

Numbers and letters on reading head casting and alignment

brackets correspond when assembled.

Determining cable direction

Determine cabel exit direction before mounting the encoder.

To change the cable exit direction, remove the cover plate

and rotate it 180°.

7 Preparing the remounting

K1 - cable exit right side

K2 - cable exit left side

T-10 torx screw

Do not pull out the PCB!

Do not clamp the wires!

T-10 torx screw

max. 70 Ncm!

spring clip

SENC 150 Reading Head Replacement Instructions

Remounting the encoder assembly

Remount the encoder as it was originally installed, using the

same brackets, fasteners and spar or support.

Refer to the encoder manual (ID: 516291-22) as from section 5.

Removing the alignment brackets

Slide the brackets away from the reading head.

Remove the alignment brackets and save for future use.

8 Remounting the encoder assembly

Andere Handbücher für SENC 150

Inhaltsverzeichnis

Andere ACU-RITE Medienkonverter Handbücher

ACU-RITE

ACU-RITE SENC 150 Bedienungsanleitung

ACU-RITE

ACU-RITE ENC 150 Bedienungsanleitung

ACU-RITE

ACU-RITE ENC 250 Bedienungsanleitung

ACU-RITE

ACU-RITE ENC 150 Bedienungsanleitung

ACU-RITE

ACU-RITE SENC 150 Bedienungsanleitung

ACU-RITE

ACU-RITE SENC 150 Bedienungsanleitung

ACU-RITE

ACU-RITE SENC 150 Bedienungsanleitung

ACU-RITE

ACU-RITE ENC 250 Leitfaden

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung