CYP EL-7400V Bedienungsanleitung

EL-7400V

HDMI/VGA/Display Port Presentation Switch & Scaler

with HDMI & HDBaseT™ Outputs

OPERATION MANUAL

DISCLAIMERS

The information in this manual has been carefully checked and is

believed to be accurate. CYP (UK) Ltd assumes no responsibility for any

infringements of patents or other rights of third parties which may result

from its use.

CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be

contained in this document. CYP (UK) Ltd also makes no commitment to

update or to keep current the information contained in this document.

CYP (UK) Ltd reserves the right to make improvements to this document

and/or product at any time and without notice.

No part of this document may be reproduced, transmitted, transcribed,

stored in a retrieval system, or any of its part translated into any language

or computer file, in any form or by any means—electronic, mechanical,

magnetic, optical, chemical, manual, or otherwise—without express

written permission and consent from CYP (UK) Ltd.

Version 1.1 August 2011

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be

trademarks of the companies with which they are associated.

SAFETY PRECAUTIONS

Please read all instructions before attempting to unpack, install or operate

this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this

equipment:

• Always follow basic safety precautions to reduce the risk of fire,

electrical shock and injury to persons.

• To prevent fire or shock hazard, do not expose the unit to rain,

moisture or install this product near water.

• Never spill liquid of any kind on or into this product.

• Never push an object of any kind into this product through any

openings or empty slots in the unit, as you may damage parts inside

the unit.

• Do not attach the power supply cabling to building surfaces.

• Use only the supplied power supply unit (PSU). Do not use the PSU if

it is damaged.

• Do not allow anything to rest on the power cabling or allow any

weight to be placed upon it or any person walk on it.

• To protect the unit from overheating, do not block any vents or

openings in the unit housing that provide ventilation and allow for

sufficient space for air to circulate around the unit.

REVISION HISTORY

VERSION NO. DATE SUMMARY OF CHANGE

v1.00 18/03/2018 First release

v1.01 17/05/2018 Amended "Cat" labelling to include Cat7

CONTENTS

1. Introduction...........................................6

2. Applications ...........................................6

3. Package Contents ..................................6

4. System Requirements ...........................7

5. Features..................................................7

6. Operation Controls and Functions .......8

6.1 Front Panel................................................... 8

6.2 Rear Panel..................................................... 9

6.3 Remote Control........................................10

6.4 IR Cable Pinouts .......................................11

6.5 OSD Menu ..................................................12

6.6 WebGUI Control .......................................30

6.7 RS-232 Control..........................................35

6.8 Telnet Control............................................35

6.9 RS-232 and Telnet Commands............36

7. Connection Diagram .......................... 58

8. Specifications...................................... 59

8.1 Technical Specifications ........................59

8.2 Video Specifications................................61

8.3 Audio Specifications...............................62

9. Acronyms............................................. 63

1. INTRODUCTION

This scaler has DisplayPort, HDMI and PC (VGA) inputs which can be freely

selected for output at a scaled resolution of the user’s choosing over the

mirrored HDMI and HDBaseT outputs. This unit also includes separate

analogue and digital audio outputs to provide additional playback ex-

ibility. Support for HDMI output resolutions up to 1080p/WUXGA (RB) and

Analogue to Digital Conversion (ADC) functionality combine to allow for a

wide range of AV signals to be displayed on the connected HDMI displays.

Beyond video switching and scaling, this unit also features useful audio

functions. The Optical Audio Return (OAR) feature supports transmitting

optical audio from a compatible HDBaseT Receiver to this unit for local

playback. An integrated audio DSP with gain control for routing audio

and controlling background audio levels adds to the versatility of this

product. The HDBaseT output can provide 48V PoH to power to compat-

ible HDBaseT Receivers. The unit can be controlled via front panel buttons

with an On-Screen Display (OSD), WebGUI, IR remote, Telnet, and RS-232

making it exceptionally versatile.

2. APPLICATIONS

Analogue and Digital source integration

Upscaling standard denition sources for high-denition displays

Conference centers

Lecture halls

Schools and universities

3. PACKAGE CONTENTS

1×HDMI/DP/VGA to HDMI/HDBaseT Scaler (PSE) with OAR

1×24V/2.7A DC Power Adapter

1×Power Cord

1×3.5mm to IR Extender Cable

1×3.5mm to IR Blaster Cable

1×Remote Control (CR-176)

1×Operation Manual

4. SYSTEM REQUIREMENTS

HDMI, DisplayPort or VGA source equipment such as media players,

video game consoles, PCs, or set-top boxes.

HDMI receiving equipment such as HDTVs, monitors or audio

ampliers.

A compatible HDBaseT receiver with 48V PoH and Optical Audio

Return support is strongly recommended.

The use of “Premium High Speed HDMI”cables is highly recommended.

The use of industry standard Cat.6, Cat.6a or Cat.7 cable is highly

recommended.

5. FEATURES

HDMI 1.3, DisplayPort 1.1, and DVI 1.0 compatible

HDCP 1.x compliant

Multiple video and audio inputs: 1 DisplayPort, 2 HDMI, 2 VGA, and 3

stereo audio

Mirrored HDMI and HDBaseT outputs

Supports input and output resolutions up to 1080p/WUXGA (RB)

Analogue stereo and digital coaxial breakout audio outputs

Supports pass-through of LPCM 2.0 audio

Supports the Optical Audio Return (OAR) function to transmit audio

from a compatible HDBaseT receiver to this unit

Audio DSP with gain control for routing audio and controlling

background audio levels

HDBaseT feature support: HD Video and Audio, Ethernet, 48V PoH, and

Control (bidirectional IR/RS-232 pass-through)

HDBaseT output provides 48V PoH (PSE) to power to compatible

HDBaseT Receivers (PD)

EDID management support

Remote control provides discrete input source selection

Controllable via front panel controls with OSD, RS-232, Telnet, WebGUI,

and IR remote

6. OPERATION CONTROLS AND FUNCTIONS

6.1 Front Panel

1122

POWER DP HDMI VGA

MENU– +ENTER

720P

XGA

EL-7400V

1 2 3 4 5 6

1POWER Button & LED: Press this button to power the unit on (Green

LED) or place it into stand-by mode (Red LED).

2IR Window: Accepts IR signals from the included IR remote for control

of this unit only.

3DP/HDMI/VGA Buttons & LEDs: Press any of these buttons to switch

immediately to the corresponding input. An LED will illuminate to

indicate which source is currently selected.

4MENU Button: Press to enter the OSD menu, or to back out from

menu items.

Note: Pressing and holding the “MENU” button while connecting the

power supply will reset all settings to the factory defaults. Pressing

“MENU” and “+” together will reset the output resolution to XGA

(1024×768@60Hz). Pressing “Menu” and “−” together will reset the output

resolution to 720p@60Hz.

5− & + Buttons: Press to move up and down or adjust selections within

menus.

Note: When not in the OSD, pressing “−” will activate the Auto Adjust

function for VGA sources. Pressing “+” will briefly show the OSD

information display.

6ENTER Button: Press to confirm a selection within the OSD or to go

deeper into a menu item.

6.2 Rear Panel

LAN

OUT

CAT5e/6/7

OPT.

HDMI

DP 1122HDMIAUDIOCOAX

SERVICE RS-232

AUDIO

VGA

RXTX

RS-232

DC 24V

V+

GND

GND GND

V+

OUTPUT

INPUT 12

1112

38910 4 5 6 7

1DP IN: Connect to DisplayPort source equipment such as a PC or

laptop.

Note: In some rare cases, digital DisplayPort audio can’t be supported. In

those cases, please use analogue audio input 1.

HDMI IN 1~2: Connect to HDMI source equipment such as media

players, game consoles or set-top boxes.

VGA IN 1~2: Connect to VGA source equipment such as PCs or

laptops.

AUDIO IN 1~3: Connect to the stereo analogue outputs of devices

such as CD players or PCs.

Note: In “Audio Follows Video” mode, Audio 1 maps to the digital inputs

(DisplayPort, HDMI 1 & HDMI 2), Audio 2 maps to VGA 1 and Audio 3

maps to VGA 2.

2HDMI OUT: Connect to HDMI TVs, monitors or amplifiers for digital

video and audio output.

AUDIO OUT: Connect to powered speakers or an amplifier for stereo

analogue audio output.

COAX OUT: Connect to powered speakers or an amplifier for digital

audio output using an appropriate coaxial cable.

3OPT. OUT: Connect to powered speakers or an amplifier for digital

audio output using an appropriate optical cable. Audio is sourced

from the Optical Audio Return input on the connected HDBaseT

Receiver.

4RS-232 OUT: Connect to a PC, laptop or other serial control device

with a 3-pin adapter cable for the extension of RS-232 signals to the

HDBaseT Receiver.

5IR IN: Connect to the provided IR Extender to extend the IR control

range of remotely located devices. Ensure that the remote being used

is within direct line-of-sight of the IR Extender.

6IR OUT: Connect to the provided IR Blaster to transmit IR signals to

devices within direct line-of-sight of the IR Blaster.

7CAT5e/6/7 OUT: Connect to a compatible HDBaseT Receiver with a

single Cat.5e/6/7 cable for transmission of all data signals.

8LAN: Connect directly, or through a network switch, to your PC/

laptop to control the unit via Telnet/WebGUI and to extend the

network to both ends of the HDBaseT connection.

9RS-232: Connect directly to a PC, laptop or other serial control device

to send RS-232 commands to control the unit.

10 SERVICE: This slot is reserved for firmware update use only.

11 DC 24V: Plug the 24V DC power adapter into this port and connect it

to an AC wall outlet for power.

6.3 Remote Control

1POWER: Press this button to power the unit on or

place it into stand-by mode.

2DP/HDMI 1~2/PC 1~2: Press any of these buttons

to switch immediately to the corresponding input.

3MENU: Press this button to enter the OSD menu.

4EXIT: Press this button to exit the menu or the

current selection in the OSD menu.

5OK////& VOL/−/+: Press OK to confirm the

selection or press the arrow buttons to navigate

the OSD menu. When the OSD menu is not active,

use the LEFT/RIGHT (◄/►) buttons to control the

volume level.

6AUTO ADJUST: Press this button to activate the

Auto Adjust function for VGA sources.

7RESET: Press this button to reset the device back to the default

settings.

CR-176

PC 1 PC 2

EXIT

POWER

RESET

HDMI 1HDMI 2DP

VOL

AUTO

ADJUST

Inhaltsverzeichnis

Andere CYP Medienkonverter Handbücher

CYP

CYP CP-VSRGB Bedienungsanleitung

CYP

CYP CM-398M Bedienungsanleitung

CYP

CYP SY-401V Bedienungsanleitung

CYP

CYP n-TECH SOLUTIONS nT15BX02/CLUX-11CD Bedienungsanleitung

CYP

CYP CLUX-SDI2HCA Bedienungsanleitung

CYP

CYP CP-1262HAT Bedienungsanleitung

CYP

CYP CP-268 Bedienungsanleitung

CYP

CYP CUSB-603 Bedienungsanleitung

CYP

CYP CSC-6013 Bedienungsanleitung

CYP

CYP CSDI-12SR Bedienungsanleitung

CYP

CYP CV-401D Bedienungsanleitung

CYP

CYP AU-D6-H Bedienungsanleitung

CYP

CYP EL-6010-4K22 Bedienungsanleitung

CYP

CYP CSLUX-300 Bedienungsanleitung

CYP

CYP DCT-3AN Installationshandbuch

CYP

CYP CP-255I Bedienungsanleitung

CYP

CYP EL-31C-4K22 Bedienungsanleitung

CYP

CYP DCT-3 Bedienungsanleitung

CYP

CYP CPLUS-V2PE Bedienungsanleitung

CYP

CYP CLUX-M2SDI Bedienungsanleitung

CYP

CYP CLUX-SDI2VS Bedienungsanleitung

CYP

CYP CP-1261D Bedienungsanleitung

CYP

CYP CS-801H Bedienungsanleitung

CYP

CYP CSO-T2 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung

Expert

Expert EX-9543 Bedienungsanleitung