Adam Equipment CQT 202 Montageanleitung

@Adam Equipment Company 2011

Adam Equipment

CQT Service

ADAM EQUIPMENT CO. LTD.,

revA, January 2011

@Adam Equipment Company 2011

©Adam Equipment Company 2011

CONTENTS

1CQT

FEATURES ............................................................................................ 3

2CQT

SPECIFICATIONS................................................................................... 3

3INTRODUCTION .......................................................................................... 4

4REMOVING

THE

COVER ............................................................................... 5

5LOAD

CELL

DAMAGE.................................................................................... 5

5.1 5.1

A/D

COUNTS ................................................................................ 5

6PRINCIPLE

OPERATION ........................................................................... 7

7DEALER PARAMETERS .......................................................................... 8

7.1 FILTER.............................................................................................. 8

7.2 ZERO TRACKING RANGE............................................................... 8

7.3 LINEARITY CALIBRATION POINT................................................... 8

7.4 LINEARITY CALIBRATION AMEND VALUE .................................... 9

7.5 CAPACITY ........................................................................................ 9

7.6 DIVISION .......................................................................................... 9

7.7 CALIBRATION WEIGHT................................................................... 9

7.8 CALIBRATION ................................................................................ 10

8ERROR

MESSAGES ..................................................................................... 10

9TROUBLE SHOOTING GUIDE ............................................................... 12

©Adam Equipment Company 2011

1 CQT

FEATURES

•Auto hut off

•Auto zero tracking

•Auto backlight (optional)

•Low battery indication

•Kg/g/lb/oz/ct/dr/GN/N/tl.t conver ion

•Large LCD (6 digit 18 mm high)

•Large quare SS pan

•Net weight/ tability indication

•Auto calibration

2CQT

SPECIFICATIONS

Model # CQT-202 CQT- 251 CQT-601 CQT-1501 CQT-2601 CQT-2000 CQT-5000

Maximum

Capacity 200g 250g 600g 1500g 2600g 2000g 5000g

Readability 0.01g 0.1g 0.1g 0.1g 0.1g 1g 1g

Re olution 1:20000 1:2500 1:6000 1:15000 1:26000 1:2000 1:5000

Repeatability

(Std Dev) 0.02g 0.1g 0.1g 0.2g 0.2g 1g 1g

Linearity ± 0.02g 0.1g 0.1g 0.2g 0.2g 1g 1g

Unit of

Mea ure kg / g / lb / oz / ct / dr / GN / N/tl.t

Stabili ation

Time 3 econd 2 econd 3 econd 2 econd

Operating

Temperature

0ºC to 40ºC

32ºF to 104ºF

Power Supply 12VAC @ 150mA adapter or 6x AA batterie

Calibration Pu h button calibration u ing external ma

Calibration

100g/

200g

100g/

200g

200g/

400g

/600g

500g/

1000g/

1500g

1000g/

2000g

1000g/

2000g

1000g/300

0g/5000g

Di play 6 digit LCD, 18mm digit , with backlight

Draft hield

(diameter x h)

132mm ø x 82mm

(5.2” ø x 3.2”) N/A

Balance

Hou ing ABS Pla tic

Pan Size 120mm ø (5.1” ø) 145mm ø (5.7” ø)

Overall

Dimen ion

(w x d x h)

173 x 255 x 86mm (6.8” x 10” x 3.3”)

Without draft hield

Net Weight 820g (1.8lb)

©Adam Equipment Company 2011

3INTRODUCTION

The cale are all ba ed on re i tance train gauge load cell . The load

cell output a mall voltage in re pon e to a load placed on the weighing

platform. The voltage i in the range of approximately 10mv for a full

capacity load.

The ignal from the load cell i pre ented directly to an A/D converter for

conver ion to a digital value for u e by the microproce or.

It may be nece ary to replace a load cell if it i damaged.

The load cell connection are:

Before any change are made to the cale, it will be nece ary to

trouble- hoot the problem and determine the be t method to olve the

problem . Refer to the Trouble- hooting Guide for ugge tion .

High Re olution cale

CQT 202,1501 & 2601

Signal - Black

Signal + Green

Shield Yellow

Ext - White

Ext + Red

Low Re olution cale

All other

Signal - White

Signal + Green

Ext - Black

Ext + Red

©Adam Equipment Company 2011

4 REMOVING

THE

COVER

If it become required to remove the cover, you hould be very careful

a pulling or pre ing on the load cell during thi procedure can damage

it very ea ily.

When removing the crew (4 mall crew below the cale) hold the

cover to the ba e and en ure not to pre on the balance ca e a the

load cell can be damaged. The load cell i attached to the ba e.

The load cell are protected by overload and under-load top . The e

top are either plate that contact the cover or crew that are

acce ible from the out ide of the cale .

Refer to the Trouble- hooting Guide for the po ible cau e of any

problem.

5LOAD

CELL

DAMAGE

5.1

A/D

COUNTS

Pre [Unit] fir t and then pre [On/Off], while keeping the [Unit] key

pre ed to enter the dealer parameter . The di play will how the

ver ion number and then reque t pa word .

Pre [Unit],[Unit], [T re], [Unit], [Unit] in equence to enter the etting

mode.

Pre the [Unit] key everal time until you enter the calibration etting .

Then you can ee the A/D count.

To ee the every divi ion A/D count ,for example: the CQT202 with the

readability 0.01g.

Fir t record the current A/D count, e.g 43860, then put on the 1g weight

to ee the new A/D Count ,eg:44198. So the divi ion A/D count i

(44198-43860)/100=3.38. The count hould bigger than 3.

©Adam Equipment Company 2011

If the divi ion A/D count are out ide thi range or cannot be een then

it will be nece ary to trouble hoot the load cell, load cell connection

to verify the load cell i working correctly and ha not been damaged.

The mo t common rea on for a cale to fail i that the load cell ha been

damaged. The damage can be due to two primary cau e . The fir t i

the phy ical damage due to an overload or an impact from the ide and

the econd i damage due to the environment, uch a moi ture,

extreme heat or a cut cable if the cable are expo ed.

With the CQT cale it i po ible the load cell i damaged uch that the

cale till operate when the cale i calibrated but not when a mall

ma i put on the pan. Thi will become apparent when the cale read

correctly at the calibration ma but i not correct at lower ma e . The

cale may till zero OK after power i applied but it will not regi ter a

weight value for maller weight .

Check the A/D count in thi ca e.

©Adam Equipment Company 2011

6PRINCIPLE

OPERATION

The train gauge load cell i a method of mea uring the amount of tre

put onto a metal tructure due to a weight being upported by the

tructure. The tre i mea ured u ing 4 train gauge en or mounted

in a particular way on the metal tructure.

The e 4 train gauge are connected in uch a way that they form a

Wheat tone bridge. See the figure below. In the imple t load cell

there are only the 4 re i tance of the train gauge to con ider.

Normally without a load on the load cell, all the re i tance are the

ame. However, when the load cell ha a weight on it, two of the train

gauge will be in compre ion (A and D) and the re i tance will decrea e

and the other two will be in ten ion (B and C) and their re i tance will

increa e.

350 ohm

350ohm

-S

-E

BALANCED BRIDGE

10 VOLT POWER

SUPPLY

Vout = O VOLTS,

BETWEEN +S AND -s

351ohm

349ohm

351ohm

349ohm

-S

-E

UNBALANCED BRIDGE

FULL CAPACITY LOAD

ON THE LOAD CELL

10 VOLT POWER

SUPPLY

Vout = 0.028 VOLTS (28mv),

BETWEEN +S AND -s

Thi will cau e the bridge to become unbalanced. When the bridge ha a

voltage acro it from +E to -E then the ignal output at +S and -S will

how a voltage of zero volt with no load and a mall voltage

proportional to the load a the load i increa ed. Typical load cell how

10mv of ignal if the excitation voltage i 5volt and the load cell i fully

loaded.

To check the load cell, apply power to the cale and mea ure a voltage

between the S+ and S- wire when de- oldered from the PCB. The

voltage hould be le than 2millivolt with no load on the cale,

increa ing a the load i applied. The voltage between the E+ and E-

wire hould be 5V.

©Adam Equipment Company 2011

DEALER PARAMETERS

•Pre [Unit] fir t and then pre [On/Off], while keeping the

[Unit] key pre ed to enter the dealer parameter . The

di play will how “Cqt-1.0 Cqt” “080410 Cqt” and then

reque t pa word .

•Pre [Unit], [Unit], [T re], [Unit], [Unit] in equence to

enter the etting mode.

7.1

FILTER

•The di play how “Cqt-1.0 Cqt”and“080410 Cqt”, 1 econd

later the balance will enter filter etting and the LCD will

how “X FIL”. “X” i the value for the amount of filtering to

be done. Set a value of 1 to 6. A larger number i more

filtering and a lower re pon e. Default i “1”.

•Pre [T re] key to croll through the option .

•Pre [Unit] to confirm and enter zero tracking range

etting.

7.2

ZERO TRACKING RANGE

•When enter zero tracking range etting, the di play will

how “X ZEO”. X i the value for the amount of auto-zero

range. Set a value of 1 to 7. A larger number i a larger

range. Default i “1”.

•Pre [T re] key to croll through the option .

•Pre [Unit] to confirm and enter linearity calibration point

etting.

7.3

LINEARITY CALIBRATION POINT

•Thi function mean etting a point to u e in linearity

calibration.

•When enter linearity calibration point etting, the di play

will how “X LID”. “X” i the value for point number. Set a

value of 0 to 5. “0” mean the point i at 1/3 of capacity, “1”

i 1/2, “2” i 2/3, “3” i 5/6, “4” i 6/7, “5” i 1. Default i

“0”.

•Pre [T re] key to croll through the option .

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Adam Equipment Skala Handbücher

Adam Equipment

Adam Equipment LBK Series Bedienungsanleitung

Adam Equipment

Adam Equipment MDW-160M Bedienungsanleitung

Adam Equipment

Adam Equipment CFC SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment PGL SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment NBL 84 e/i Bedienungsanleitung

Adam Equipment

Adam Equipment CB 501 Bedienungsanleitung

Adam Equipment

Adam Equipment CBW Series Bedienungsanleitung

Adam Equipment

Adam Equipment ASC Bedienungsanleitung

Adam Equipment

Adam Equipment RAV Series Bedienungsanleitung

Adam Equipment

Adam Equipment DCT 201 Bedienungsanleitung

Adam Equipment

Adam Equipment MDW - 250L Bedienungsanleitung

Adam Equipment

Adam Equipment CCSA series Bedienungsanleitung

Adam Equipment

Adam Equipment HIGHLAND HCB123 Bedienungsanleitung

Adam Equipment

Adam Equipment HIGHLAND SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment CORE SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment NETS ME Price Bedienungsanleitung

Adam Equipment

Adam Equipment CBC SERIES Bedienungsanleitung

Adam Equipment

Adam Equipment BFW 75 Bedienungsanleitung

Adam Equipment

Adam Equipment CB Balance Bedienungsanleitung

Adam Equipment

Adam Equipment LHS Series Bedienungsanleitung

Adam Equipment

Adam Equipment Warrior Series Bedienungsanleitung

Adam Equipment

Adam Equipment QBW Series Bedienungsanleitung

Adam Equipment

Adam Equipment IHS Series Bedienungsanleitung

Adam Equipment

Adam Equipment BCT Series Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung