Adaptec SlimSCSI APA-1460A Bedienungsanleitung
U
SER
S
G
UIDE
S
LIM
SCSI 1460 A
DAPTER
© 1997 Adaptec, Inc.
All rights reserved. Adaptec, and the
Adaptec logo are trademarks of Adaptec,
Inc. which may be registered in some
jurisdictions.
Printed in Singapore
STOCK NO.: 511605-00, Rev. A KL 9/97
R
▼ ▼ ▼ ▼ SlimSCSI 1460 Adapter
User’s Guide
iii
▼ ▼ ▼ ▼ Contents
Introduction 1
Where Do I Start? 1
Contents of Kit 1
System Requirements 2
Installing the SlimSCSI 1460 2
Completing the Installation 6
Updating the Windows 95 Miniport Driver 6
Completing the SlimSCSI Installation in Windows 3.1 7
Completing the SlimSCSI Installation in Windows NT 8
If Windows NT Is Not Installed on Your PC 8
If Windows NT Is Installed on Your PC 9
Completing the SlimSCSI Installation in OS/2 11
Using the SlimSCSI 1460 13
Hot Plugging 13
Disk Partitioning 14
Understanding SCSI 15
SCSI IDs 15
Terminating the SCSI Bus 16
Obtaining SCSI Cables 16
Connector Types 17
Troubleshooting 18
General Hardware Troubleshooting 18
Windows 3.1 Troubleshooting 19
Windows 95 Troubleshooting 19
Windows NT Troubleshooting 22
OS/2 Troubleshooting 23
iv
SlimSCSI 1460 Adapter User’s Guide
Troubleshooting with CardWizard Pro 23
Contacting Adaptec 25
Electronic Support 25
Technical and Product Support 25
Sales and Ordering Information 26
❒
1
Introduction
Congratulations on your purchase of Adaptec’s SlimSCSI®1460.
The SlimSCSI 1460 allows you to connect up to three SCSI devices to
your portable PC, including Zip drives, CD-ROM drives, hard disk
drives, scanners, and other devices.
Where Do I Start?
1
Follow the instructions for installing the SlimSCSI 1460 and
connecting your SCSI devices to it.
2
Install the software driver for the operating system you are
using - Windows®95 (page 6), Windows®3.1 (page 7),
Windows NT™(page 8), or OS/2 (page 11).
3
(Optional) Install Adaptec EZ-SCSI software by following the
instructions in the Adaptec EZ-SCSI Quick Reference. (EZ-SCSI is
not required to operate the SlimSCSI 1460.)
Contents of Kit
■SlimSCSI 1460 PC Card-to-SCSI Adapter
■Windows 95, Windows NT, and OS/2 driver diskettes
■SlimSCSI 1460 User’s Guide
■50-pin high-density cable and 50-pin low-density cable
■Adaptec®EZ-SCSI®software for Windows 3.1, Windows 95,
and Windows NT
■CardWizard Pro software for DOS and Windows 3.1
2
SlimSCSI 1460 Adapter User’s Guide
■Mail-in card for free DB25 cable
■Registration card
System Requirements
■Portable PC with a PC Card Type II, Type III, or Toshiba
Type IV slot
■MS-DOS version 5.x or 6.x, Microsoft Windows 95,
Windows NT version 3.51 or 4.0, Windows 3.x, Windows for
Workgroups version 3.1 or 3.11, DR DOS, OS/2 version 2.x, or
OS/2 Warp
Installing the SlimSCSI 1460
Follow these steps to install the SlimSCSI 1460 and connect your
SCSI devices to it:
1
Remove the SlimSCSI 1460 from its packaging.
2
Determine which of the two 50-pin cables you will use to con-
nect the SlimSCSI 1460 to your first (or only) SCSI device. To
do this, see which cable connector (high-density or low-
density) fits the SCSI connector on the back of the device.
Note:
If your SCSI device has a DB25 (25-pin) connec-
tor, you can order a free DB25 cable from Adaptec by
sending in the card included in this User’s Guide.
3
Installing the SlimSCSI 1460
3
Connect the SlimSCSI cable to the SlimSCSI 1460, as shown
below:
4
Plug the other end of the cable into the first (or only) SCSI
device, as shown below. Make sure the SCSI device is not
powered.
PC Card Slots
SlimSCSI 1460
SlimSCSI Connector
SCSI Connector SCSI Device
Terminator
4
SlimSCSI 1460 Adapter User’s Guide
5
(Optional) Connect up to two additional SCSI devices by daisy-
chaining them to the first device, as shown below:
6
Be sure that each SCSI device has a unique SCSI ID ranging
from 0 to 6. If any two devices have the same ID, change the
SCSI ID of one device. This is usually done by changing a
switch on the back of the device. (For more information, see
SCSI IDs on page 15.)
The diagram below shows a typical SCSI device with a select-
able SCSI ID switch:
7
Terminate the last (or only) SCSI device connected to the
SlimSCSI 1460. Read the device documentation if you are not
sure how to terminate the device, or refer to Terminating the
SCSI Bus on page 16.
SCSI Devices
Terminator
Andere Handbücher für SlimSCSI APA-1460A
1
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Adaptec Adapter Handbücher
Adaptec
Adaptec AHA-1540C Bedienungsanleitung
Adaptec
Adaptec Trantor T260 Handbuch
Adaptec
Adaptec AHA-2910 Bedienungsanleitung
Adaptec
Adaptec AHA-1520B Bedienungsanleitung
Adaptec
Adaptec SlimSCSI 1450 Bedienungsanleitung
Adaptec
Adaptec APA-1480 SlimSCSI Bedienungsanleitung
Adaptec
Adaptec AHA-3980 Bedienungsanleitung
Adaptec
Adaptec 9110G Service-Handbuch
Adaptec
Adaptec ARO-1130U2 Montageanleitung
Adaptec
Adaptec AUA-2000 Bedienungsanleitung
Adaptec
Adaptec T-128 Bedienungsanleitung
Adaptec
Adaptec AHA-1510A Series Bedienungsanleitung
Adaptec
Adaptec ASH-1205SA Bedienungsanleitung
Adaptec
Adaptec AFW-8300 Bedienungsanleitung
Adaptec
Adaptec AFW-1430 Bedienungsanleitung
Adaptec
Adaptec AFW-4300 Handbuch
Adaptec
Adaptec AUA-1420A Bedienungsanleitung
Adaptec
Adaptec AUA-1411 Bedienungsanleitung
Adaptec
Adaptec ACB-2070A Bedienungsanleitung
Adaptec
Adaptec AHA-1520FS Bedienungsanleitung
