Adaptive Technologies Group SAS-100-CA Bedienungsanleitung

SAS-100-CA

Cross arm Nylock nut

Flat washer

End cap

Eyebolt

Cross arm

1/2 Flat washer

1/2 x 7” Long

hex bolt

1/2’ Nylock nut

1/2 Flat washer

Cotter pin

Nylon

friction

washer

REV00-07302015

1 of 2

Installation Guide

GridLink™ Cross Arm Kit

Step 1: For Use with Cable Kit

For use with the Adjustable Tilt Cable Kit, attach 5/16” eyebolts to cross arm

with at washers and nylock nut permanently. Align eyebolts with Cross Arm

then press on the plastic end cap (Figure 1).

Step 2: Assemble Cross Rigging Beam

For use with Adjustable Tilt Cable Kit, align the center hole of the cross arm

to the selected hole on the rigging beam then permanently secure the cross

arm using the 1/2” x 7” long hex bolt, bearing washer, at washer, nylock nut

and cotter pin. Make sure that the head of the hex bolt is towards the oor

(Figure 2).

This Universal Cross Arm part, of the GridLink™ Rigging Beam System,

adapts to GridLink™ Rigging Beams, Steerables™ wall and ceiling mounts

to provide a horizontal adjustment for aiming loudspeakers

For Tilt Cable Kit

Note to installers

Due to the wide variety of wall structures, materials and mounting

methods, these instructions assume that the installing contractor will

exercise proper judgment in selecting the mounting area and hardware.

As a guide, the installation, when complete should be capable of

supporting 5 to 10 times the actual applied load. Always use a back up

safety system such as a safety cable.

To assure a trouble free installation, read through and follow these

instructions carefully before beginning. If you have doubts about

the integrity of the structure you are mounting to or you are not

sure about the proper hardware to use, consult a structural and/or

hardware specialist.

Be sure that all of the following items are included in this kit before proceeding:

1 pc Cross Arm 1 pc Hardware kit

1 pc Instruction sheet

Note: Screws and washers to attach speaker to adapter plate are not included

Figure 1

For use with Tilt Cable kit

Figure 2

For use with Tilt Cable kit

SAS-100-CA

ALWAYS INSTALL SAFETY CABLES

WARNING: Mounting and/or suspension loudspeakers requires experienced

professionals. Improperly installed loudspeakers can result in property

damage, personal injury and/or liability to the installing contractor.

Adaptive Technologies Group

1635 E. Burnett Street | Signal Hill, CA 90755 USA

Ph: 562.424.1100 | Fax: 562.424.3520

www.adapttechgroup.com

1/4 Nylock

nut

1/4 Bolt

1/4 Flat

washer

1/4 Flat

washer

End

cap

1/2 Flat washer

1/2 Nylock nut

Nylon

friction

washer

Cotter pin

Cross arm

1/2 x 7” Long

hex bolt

REV00-07302015

2 of 2

Installation Guide

GridLink™ Cross Arm Kit

For U-bracket installation, attach the cross arm using ¼ screws, at

washers, nuts on the four outer holes on the bottom of the cross arm. Do not

tighten screws (Figure 3). Align the center hole of the Cross Arm/U-Bracket

assembly to the selected hole under the rigging beam using the 1/2” x 7”

long hex bolt, bearing washer, at washer, nylock nut and cotter pin. Tighten

to the desired friction level but do not crush tube. Tighten the four screws on

the U-Bracket permanently then press on the plastic end caps (Figure 4).

Step 3: Adjust Pan Angle

Hold both ends of the cross arm then rotate horizontally (clockwise or

counter-clockwise) until desired direction is achieved

Step 3: Adjust Tilt Angle

Refer to Adjustable Tilt Cable Kit or U-Bracket instruction sheet for

tilting directions.

For U-bracket

Figure 3

For use with U-Bracket

Figure 4

For use with U-Bracket

SAS-100-CA Cross Arm Kit Parts and Components

Cross arm 1 pc 1/4-20 x ¾” Long

hex bolt 4 pcs

1 /4” Flat washer

8 pcs

1 /4-20 Nylock

nut 4 pcs

5/16-18 Eyebolt

#22 2 pcs

5/16” Flat washer 4

pcs

5/16-13 Nylock nut

2 pcs

1 /2 x 7” Long hex bolt

w/ cross drill hole 1 pc

1/2” Nylon friction

washer 1 pc

1/2” Flat washer

2 pcs

1 /4-20 Nylock nut

4 pcs

1.5 x 3” End cap

2 pcs

3/32” Cotter pin 1 pc

Andere Adaptive Technologies Group Rack & Stand Handbücher

Adaptive Technologies Group

Adaptive Technologies Group MM-3RDX-18 Bedienungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group SAS-2WA-Series Bedienungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-024 Bedienungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group MM-016-BT Bedienungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group UB-QX500 Bedienungs- und Wartungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group MM-3RDX-120 Bedienungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-120 Bedienungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group MultiMount MM-023 Bedienungsanleitung

Adaptive Technologies Group

Adaptive Technologies Group WM-0-15-60 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung