ADB IMAGO Bedienungsanleitung
IMAGO
ME 1273 1106.01.273
Lighting Technologies
Installation Guide
Issue 1.0
www.adblighting.com Quick Start - page 1
Issue 1.0
1. Installation and Overview
Delivery and Unpacking
As soon as you receive your equipment, open the boxes and inspect the items received. If
you discover any damage, contact the carrier immediately and make any necessary claim
for the problems discovered.
Box content:
1/ IMAGO unit
2/ 12 V Power supply, and power cable
3/ USB cable
Installing the Desk
The desk and the monitor should be installed on a table or a console.
The surface of your work area should be smooth, level and sturdy.
Make sure that there is enough clearance around the desk to:
open the desk
access the rear connections
allow air circulation around vents to prevent the desk from over-heating
Power Supply
The IMAGO has a universal power supply that will operate on voltages between 100 volts
and 260 volts with a frequency range from 50 to 60 Hz.
Before powering up the desk or any of its peripherals, check that the existing voltages are
within the limits defined.
THIS EQUIPMENT MUST BE EARTHED.
Note: all connections should be made with the power turned off; otherwise functioning
may be affected and can even damage the equipment under certain conditions.
Electrical Connection
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT OPEN THE DESK.
THERE ARE NO USER SERVICEABLE PARTS WITHIN. REFER SERVICING TO
QUALIFIED ENGINEERS ONLY. LETHAL VOLTAGES ARE PRESENT INSIDE!
ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE OPENING FOR
INSPECTION.
Note: As all equipment used in computer systems, your system is sensitive to the
characteristics of the network and in particular to variations and voltage peaks.
Consequently, we advise you to use an appropriate line conditioner on this equipment.
Caring for your IMAGO
The IMAGO is manufactured from quality components and will give many years of service
if you take some basic precautions.
Do not allow any liquids or foreign objects to enter the IMAGO.
Do not apply excessive force to any of the controls. Spare parts and service are
available from your ADB distributor, but prevention is better than cure.
When connecting any devices to the IMAGO, make sure that all connections are
correct before switching on the power.
www.adblighting.com Quick Start - page 2
Issue 1.0
Connecting your IMAGO to peripherals
Connect the power cable from the 12 V Power supply
Connect the computer to this USB port with the USB cable delivered with the
product
Connect any USB device in the USB ports
Connect the DMX 5 cable(s)
Connect the desk lamp
Computer Specifications
IBM compatible PC minimum system requirements:
Dual Core Processor with 2.9 GHz CPU (recommended: Intel i3 or higher)
2 GB RAM (recommended: 4 GB RAM)
Hard-drive with minimum 64 GB (recommended type: SSD)
Network card 100/1000 T/TX
USB 2.0
Graphics card
Use High-end graphic cards with high-speed memory and a graphic processing
unit (GPU).
Resolution: 1920 x 1080
Operating systems:
1. Microsoft Windows 7
2. Microsoft Windows 8
Please run HATHOR software with all administrator rights.
Drivers Installation
The use of the IMAGO with your computer needs specific drivers.
The installation of IMAGO drivers is automatic. Start the computer, connect the IMAGO,
and install the version of HATHOR located on the USB device included in the HATHOR
software package.
Start the installation process of HATHOR via the installer (double click on the icon, and
follow the instructions).
During the installation, the drivers for IMAGO will be automatically installed.
Note: PREGO users can use any available version PREGO from 1.7.0.0.
1
2
4
5
1
2
3
4
5
3
M-1273-E-01r
ADB - Your Partner for Light
Lighting Technologies
Subject to modifications
www.adblighting.com
Belgi m N.V. ADB-TTV Technologies S.A.
(Group Headquarters) Leuvensesteenweg 585, B-1930 Zaventem
Tel : +32.2.709.32.11, Fax : +32.2.709.32.80, E-Mail : [email protected]
France ADB S.A.S. Sales Office: 92, Avenue Jean Jaurès F-92120 Montrouge
Tel : +33.1.41.17.48.50, Fax : +33.1.42.53.54.76, E-Mail : [email protected]
Factory & Gro p Logistics Centre: Zone industrielle Rouvroy F-02100 Saint- uentin
Tel : +33.3.23.06.35.70, Fax : +33.3.23.67.66.56, E-Mail : [email protected]
Inhaltsverzeichnis
Andere ADB Bedienfeld Handbücher
