Addonics Technologies MSDU5 Bedienungsanleitung

Technical Support

If you need any assistance to get your unit functioning properly, please

have your product information ready and contact Addonics Technical

Support at:

Hours: 8:30 am - 6:00 pm PST

Phone: 408-453-6212

Email: http://www.addonics.com/support/query/

T E C H N O L O G I E S

www.addonics.com

User Guide

1:5 mSATA / micro SATA

SSD Duplicator

(MSDU5)

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Unpacking and Overview

Power Cord (U.S. Version Shown)

WARNING: Please remember to

set the power supply to your local

outlet voltage prior to plugging in

the power cord. Failure to do so

may damage the power supply.

1. LCD Mangement Console

2. Source Slot

3. Target Slots

mSATA adapter

(ADMS18SA) x6

mSATA SSD

in the adapter

Micro SATA HDD

The Duplicator Panel

There are four buttons and an LCD

on the panel of HDD Duplicator.

4. LCD shows a function or a

message.

5. Use to scroll up function menus.

6. Use to scroll down function menus.

7. Use to execute a function.

8. Use to cancel a function.

Connecting the Power Cable and

Powering On

a. Connect the power cord provided

from the wall outlet to the back of

the tower.

b. Push the power button to turn on

the HDD duplicator.

ENT

ESC

5 7

6 8

Duplicator Panel

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

Quick Start

By default, the duplicator will initialize, scan for drives and offer the copy

function. Insert the source and target drives, power up the unit, wait for the

copy function to appear, then press ENT.

Canceling Functions

When selection menu options, canceling is done by pressing ESC. When the

unit is busy performing an operation such as copy, verify, or overwrite, the

operation can be canceled by holding the ESC button until the unit beeps.

Duplicator Functions

The duplicator has three menu sections: The Main menu, Setup Options, and

Advanced Setup Options. Setup Options is accessed through the Main menu.

Advanced Setup Options is accessed by holding the ESC button from any

other menu until the unit beeps.

Main Menu

1. Copy HDD

Scans the ports, then copies from the source to any targets found.

2. Async Copy HDD

Scans the ports, then copies from the source to any targets found. More

drives may be added before the process is complete, they will begin the

process as soon as they are detected.

3. Compare HDD

Scans the ports, then any targets found will be compared to the source.

4. Async Compare

Scans the ports, then any targets found will be compared to the source. More

drives to compare may be added before the process is complete, they will

begin the process as soon as they are detected.

5. PreScan Source

Reads all blocks on the source drive to confirm no I/O errors are encountered.

6. ReScan BUS

Manually scans all ports and reports how many units were found.

7. Source Size

Examines the source drive and reports total space and space used, if drive

contains compatible partitions. Press up/down to change display, ESC to exit.

8. Secure Erase

Scans all ports, then erases all data on all connected drives.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

NOTE: Target drive size is still required to be equal to or greater than source. Only works

with source drives formatted using Master Boot Record. If the source drive has a boot

record other than MBR, the entire disk will be copied as if Fast Copy were OFF. If the

source drive is formatted with a Master Boot Record and contains only FAT32 or NTFS

partitions, identical partitions will be created on the target(s) and only the files will be

copied. If the source drive with MBR format includes partitions other than FAT32 or NTFS,

all sectors of all partitions (including FAT32 and NTFS) will be duplicated.

Enabling Fast Copy may not produce bootable duplicates.

10-9. Auto Start Drive

When source drive is present, inserting a target drive will cause copy

process to begin automatically. Default setting is OFF.

10-10. Auto Start Timer

Sets delay in time after target insertion before beginning auto copy

process if Auto Start Drive is ON. Default setting is OFF (no delay).

10-11. Tolerance Size

Sets the minimum target size in percentage compared to the source that

is allowed to use for copying. Default is 100% (equal in size).

NOTE: Leaving this setting at 100% or using for minor adjustments only

is strongly recommended. Permitting target size less than source size

may result in inaccurate copies.

10-12. BootTime Delay

This option is used to set boot delay time. Default setting is 5 seconds.

10-13. Quick Compare

Sets Compare function to stop after a small amount of data has been

verified, up to 100MBytes. Default setting is OFF.

10-14. Copy with Size

Causes duplicate drive to report to an operating system the exact same

total size as source when copy is complete. Works only on drives format-

ted using a Master Boot Record. Default setting is OFF.

Advanced Setup Options

11-01. Read Error Skip

Allows duplicator to ignore I/O errors while reading source drive. Default

setting is OFF.

11-02. Update Firmware

Used to apply firmware updates. Connect a drive formatted as FAT

containing one partition with the firmware file in the root directory.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: 408-453-6212 Email: www.addonics.com/support/query/

NOTE: This function scans the entire disk before proceeding. Providing a drive that is as

small as possible is strongly recommended.

11-03. Compare Firmware

Used to confirm correct firmware. Connect a drive formatted as FAT

containing one partition with the firmware file in the root directory.

NOTE: This function scans the entire disk before proceeding. Providing a

drive that is as small as possible is strongly recommended.

11-04. Quick Erase HDD

Scans the ports, then quickly erases all sectors on all connected drives.

11-05. Full Erase HDD

Scans the ports, then completely erases all sectors on all connected

drives.

11-06. H/W Diagnostic

Starts comprehensive tests for Ram, LCD, buttons, ports and Flash.

11-07. Load Default

Resets all configuration settings to default.

11-08. Copy HPA

Enables copy functions to duplicate the source drive's Host Protected

Area. Normally this area is defined as not available to a host controller as

defined by ATA/SATA specifications.

11-09. Burn In

Runs a function continuously until aborted. Selections are Copy &

Compare, Compare, Async Cpy & Cmp, Async Compare.

www.addonics.com

Phone: 408-573-8580

Fax: 408-573-8588

Email: http://www.addonics.com/sales/query/

Andere Addonics Technologies Disc-Duplikator Handbücher

Addonics Technologies

Addonics Technologies DigiCopier III DGC3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies DGBR4DR11 Bedienungsanleitung

Addonics Technologies

Addonics Technologies ST5DVRE Bedienungsanleitung

Addonics Technologies

Addonics Technologies ST55HPMXA Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUSI325AES Bedienungsanleitung

Addonics Technologies

Addonics Technologies AEDVDCOPPM4U Bedienungsanleitung

Addonics Technologies

Addonics Technologies Jasper II 3M Bedienungsanleitung

Addonics Technologies

Addonics Technologies Jasper II JD2P3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies UDFHNVM7 Bedienungsanleitung

Addonics Technologies

Addonics Technologies UDFH7 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUSI325 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS11325DX Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS11SNDX Bedienungsanleitung

Addonics Technologies

Addonics Technologies JD2-3SN25 Bedienungsanleitung

Addonics Technologies

Addonics Technologies MSHDU11T Bedienungsanleitung

Addonics Technologies

Addonics Technologies Jasper II SID Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDMU3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies UDFUDD7 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS11NB Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS4SNDX-A Bedienungsanleitung

Addonics Technologies

Addonics Technologies DGBRC7 Bedienungsanleitung

Addonics Technologies

Addonics Technologies DGBRC3 Bedienungsanleitung

Addonics Technologies

Addonics Technologies ZHDUESA Bedienungsanleitung

Addonics Technologies

Addonics Technologies UDFH15-C Bedienungsanleitung

Beliebte Disc-Duplikator Handbücher anderer Marken

Riso

Riso CV Series Handbuch

MicroBoards Technology

MicroBoards Technology GX-2 Bedienungsanleitung

Carry

Carry Pro118 Bedienungsanleitung

CopyPro

CopyPro PowerPro II Bedienungsanleitung

Primera

Primera Max Bedienungsanleitung

Logicube

Logicube EchoPlus-NG Bedienungsanleitung

Silca

Silca Delta 2000 SA Bedienungsanleitung

Reflex7

Reflex7 Daisy Chain Series Bedienungsanleitung

Vinpower Digital

Vinpower Digital SharkCopier DC Bedienungsanleitung

Codonics

Codonics Virtua E Bedienungsanleitung

Octave

Octave Copy Master II Bedienungsanleitung

Kanguru

Kanguru U2-DVDDUPE-S Bedienungsanleitung

StarTech.com

StarTech.com 8STSATDUP11 Bedienungsanleitung

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Bedienungsanleitung

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Bedienungsanleitung

MicroBoards Technology

MicroBoards Technology Quic Disc QD-2 Bedienungsanleitung

Telex

Telex SpinWise Bedienungsanleitung

Aleratec

Aleratec 260206 Bedienungsanleitung