Addonics Technologies DVD R/RW Bedienungsanleitung
Addonics
TECHNOLOGIES
DVD±R/RW DigiCopier
Users Guide
Revision 1.0
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a
class B digital device pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If the equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is encouraged
to try and correct the interference by one or more of the following
suggestions.
• Reorient or relocate the receiving antenna
• Increase the distance between the equipment and the
receiver
• Connect the equipment to a different power outlet other than
the one where receiver is connected
• Consult a certified television or radio technician
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 1
Contents
FCC Warning ..............................................................................1
Contents......................................................................................2
Chapter 1 Preface.......................................................................3
General Information
Features......................................................................3
Chapter 2 Getting started............................................................4
Chapter 3 Switch setting on back of unit.....................................5
Switch settings description..........................................6
Chapter 4 Using the DVD DigiCopier as a stand alone Copier ..7
Chapter 5 Using the DVD DigiCopier as an external DVD±R/RW
on your PC .................................................................8
USB 2.0 interface cable ............................................9
USB 2.0 interface cable installation ..........................9
USB driver installation .............................................10
Firewire Interface cable installation .........................11
Chapter 6 Software Installation.................................................12
Chapter 7 Playing Audio CDs ...................................................13
Optional accessories.................................................13
Technical Support & Contact Information..............................…14
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 2
Chapter 1
Preface
This is a Preliminary version of the manual intended to provide advance
information on the Addonics Technologies’ external DVD DigiCopier
drive. The information is as complete and as accurate as possible as of
the publication date, but will be superseded and updated periodically by
revised manuals. The contents are subject to change without notice.
General Information
The Addonics Technologies’ DVD DigiCopier drive is a drive that is
designed to operate as a stand-alone unit and/or for PC and Laptop with
Firewire, PCMCIA, Serial ATA and USB Port.
Features
Fast one to one DVD/CD Duplicator•
•
•
•
•
•
•
•
•
•
•
Auto duplication and easy operation with no push buttons
Auto source DVD and blank CD detection
Automatic Format detection
Auto detect DVD±R, DVD±RW, CD-R and CDRW media to perform
at the maximum speed of the media
Firmware upgradeable via the build in DVD Reader
Small foot print
Can be used as an External DVD±R/RW for PC or Notebook
computers.
Connects to USB, Firewire port or PCMCIA port (by attaching
different Addonics interface cables.)
Supports buffer underrun
Includes DVD/CD Mastering software for Windows 98SE, ME, NT,
2000, XP
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 3
Chapter 2 Getting Started
Make sure that you have the following items:
For DVD±R/RW DigiCopier with USB2.0 Cable
! One DVD±R/RW DigiCopier main unit
! USB2.0 cable with 36 pin connector
! Sonic MyDVD Software
! DVD/CD Mastering software
! MPEG II CD playback software
! USB driver diskette
! Power Cable
! This User Guide
For DVD±R/RW DigiCopier with Firewire Cable
! One DVD±R/RW DigiCopier main unit.
! Firewire cable with 36 pin connector
! Sonic MyDVD Software
! DVD/CD Mastering Software
! MPEG II CD playback software
! Power Cable
! This User Guide
For DVD±R/RW DigiCopier with Serial ATA Cable
! One DVD±R/RW DigiCopier main unit.
! Serial ATA cable with 36 pin connector
! Sonic MyDVD Software
! DVD/CD Mastering Software
! MPEG II CD playback software
! Power Cable
! This User Guide
For DVD±R/RW DigiCopier only
! One DVD±R/RW DigiCopier main unit.
! Power Cable
! This User Guide
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 4
Chapter 3 Switch Settings on back of unit
Figure 1
S3
S2
S1
C2
C1
C1 – Analog audio connectors
C2 – Interface cable connector
S1 – Duplicator and External switch
Up position = Duplicator
Center = Neutral
Down position = External DVD±R/RW
S2 – Buzzer
6 = ON (factory default)
7 = OFF
0-5 (reserved)
S3 – functional switch
0 = Copy (factory default) 4 = Compare
1 = Test 5 = Erase
2 = Test & copy 6 = Update Firmware
3 = Verify 7 = Auto play audio
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 5
DVD DigiCopier Switch Settings description
# Copy, Test, Test and Copy - after placing the source CD and a
Blank Disc into the target DVD±R/RW drive, the copy controller
will detect if the disc in the writer is a blank one. If it is a blank
disc, the copy controller will automatically begin copying after 5
seconds. If it is a rewriteable disc, the controller will erase first
then will proceed to copy.
During copying the DVD±ROM drive Eject key will be locked in
order to prevent failure. But the DVD±R/RW drive key is not lock,
so suspension is possible.
# Verify or Compare - after placing the source CD and a target
disc into the DVD±R/RW drive, the copy controller will detect if
the disc in the writer is ready. If it is, the copy controller will
automatically begin verification or comparison after 5 seconds. If
the disc is a blank one, both verification and comparison are
feasible but errors will appear after accomplishment.
# Erase - after a Rewriteable disc into the DVD±R/RW drive, the
copy controller will detect if the disc in the writer is ready. If it is,
the copy controller will automatically begin erasing after 5
seconds.
# Update Firmware – Copy the new firmware file onto a blank CD
and placing the disc with onto the DVDROM drive (top drive). If it
is ready, the firmware will be start updating after 5 seconds.
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 6
Chapter 4
Using the DVD±R/RW DigiCopier as a Stand Alone
DVD±R/RW Copier
# Connect the power cable to the back of the DVD DigiCopier.
# Plug in the Power Cord to the AC Power Source
(+90~+250VAC)
# Set the switch (S1 on figure 1, page 6) at the back to Duplicator
position. Then turn the power on at the front to start the DVD
DigiCopier as a Stand Alone DVD Copier
# LED Display will now lit at the front, will do a series of check, will
check Firmware version. Once the initiation is completed (about
10 -15 seconds), the Power light will stay lit.
# You are now ready to use the DVD±R/RW DigiCopier.
# Insert a source DVD or CD on the top DVDROM Drive,
# Insert a Blank DVD±R, DVD±RW, CD-R or CD-RW Disc at the
Bottom DVD±R/RW drive
# Close the Tray and that’s it.
# Once the copy is done, the bottom tray will open and you may
now use the created Disc.
Note: The duplication time depends on the amount of data on the source
and the type of media in the destination drive. A full 680MB CD takes
approximately 6 – 7 minutes to copy onto a 16X certified CD-R. A full
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 7
length DVD movie may take 30 minutes to copy onto a 2X certified
DVD±R
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 8
Chapter 5
Using DVD DigiCopier as an external DVD±R/RW on your
PC
Installation
# Connect the power cable to the back of the DVD DigiCopier.
# Plug in the Power Cord to the AC Power Source
(+90~+250VAC)
# Connect the Interface cable to the back of the DVD DigiCopier
and the other end to your computer or Notebook interface port.
# Set the switch (S1 on figure 1, page 6) at the back to External
position. Power On the unit at the front to start the DVD
DigiCopier.
# LED Display will now lit at the front, will do a series of check, will
check Firmware version. Once the initiation is completed (about
10 -15 seconds), both the Power light and the External light will
stay lit.
# You are now ready to use the DVD±R/RW drive (the bottom
drive) in the DVD DigiCopier as an external storage device
connected to your computer.
# When the DVD DigiCopier is used on a Computer, Only the
DVD±R/RW drive at the bottom Works. The DVDROM drive at
the top will be DISABLED
Addonics Technologies – DVD±R/RW DigiCopier Users Guide v1.0 9
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Addonics Technologies DVD-Laufwerk Handbücher
Addonics Technologies
Addonics Technologies AEMDVRBY Bedienungsanleitung
Addonics Technologies
Addonics Technologies Mobile DVDR/RW Bedienungsanleitung
Addonics Technologies
Addonics Technologies ZDVRRWESU Bedienungsanleitung
Addonics Technologies
Addonics Technologies ZDVRRWESU Bedienungsanleitung
Addonics Technologies
Addonics Technologies Mobile DVD/CDRW Bedienungsanleitung
Addonics Technologies
Addonics Technologies Pocket DVD Bedienungsanleitung
