Adeunis RF IOT TOOLBOX BUNDLE ETHERNET Bedienungsanleitung

IOT TOOLBOX

Create an IoT chain quickly and easily

QUICK START GUIDE

Version 1.1.1

1 Gateway

Ethernet or

4G option

3 Transmitters

of your choice

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

Table of contents

1. INFORMATIONS 3

2. 4G Gateway Installation 4

3. ETHERNET Gateway Installation 5

3.1. Cables connexion 5

3.2. Computer Network Settings 6

3.3. Gateway Network Settings 8

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

1. INFORMATIONS

Ethernet Toolbox version composition:

• 1 Multitech gateway

• 1 Antenna LoRa 868MHz (White)

• 1 Power suppy adaptor

• 1 Ethernet cable (2m)

• 1 USB cable

• 3 Adeunis IoT devices

4G Toolbox version composition:

• 1 Multitech gateway

• 1 Antenna LoRa 868MHz (White)

• 1 Antenna GSM 4G (Black) + 1 spare

• 1 Power suppy adaptor

• 1 Ethernet cable (2m)

• 1 USB cable

• 3 Adeunis IoT devices

Your Iot Toolbox is already fully set to retrieve data from Adeunis IoT devices. However, to send this data to an application server in order to

monitor them from anywhere, the Toolbox needs to be connected on an Internet Network. Depending of your type of IoT Toolbox, you may need

to connect the gateway to your company network.

If you have an Ethernet IoT Toolbox version,

Jump directly to the page 5.

To know what is your IoT Toolbox version, check the sticker on the side of the box, like display below:

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

2. 4G GATEWAY INSTALLATION

1) Connect the white antenna LoRa on the « RF » connector of the Multitech gateway.

2) Connect the black antenna GSM on the « CELL » connector of the Multitech gateway.

3) Connect the power supply adaptor on the Multitech gateway.

4) Supply the gateway by connecting the other extremity of the adaptor to an outlet.

Your 4G IoT Toolbox is now ready, you can proceed to

the activation of adeunis® devices and

monitor your data on your WebApp.

NOTE: Do not continue reading the document if you have a 4G IOT TOOLBOX version.

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

3. ETHERNET GATEWAY INSTALLATION

3.1. Cables connexion

1) Connect the white antenna LoRa on the « RF » connector of the Multitech gateway.

2) Connect the Ethernet cable on « E-NET » port of the Multitech gateway.

3) Connect the power supply adaptor on the Multitech gateway.

4) Supply the gateway by connecting the other extremity of the adaptor to an outlet.

5) Connect the other extremity of the Ethernet cable to your PC.

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

3) Right-click on « Local Area Connection » and click on « Properties ».

3.2. Computer Network Settings

1) On your computer, click on:

« Start Menu > Control Panel > Network and Sharing Center ».

(For Windows 8 and higher, search for and open Control Panel and select Network And Internet).

2) Click « Change adapter settings ».

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

5) Select « Use the following IP address » and enter the IP address 192.168.2.3 and the Subnet Mask 255.255.255.0.

Then click OK and close the Local Area Connection properties window.

4) Select « Internet Protocol Version 4 » (TCP/IPv4) and click on « Properties ».

255.255.255.0

192.168.2.3

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

3.3. Gateway Network Settings

You are now able to communicate with the Gateway. It is necessary to connect your gateway to your company network in order to have a link

between the LoRa Network and Internet. To do so, you need to ask to your network administrator an IP address, the network mask and the

company gateway that you will address to the Multitech gateway.

1) Open your internet browser and type the address 192.168.2.1.

2) Log in with the login « admin » and the password « admin ».

3) Click on « Setup » and then « Network interfaces ».

4) Click on the pencil at the right of the page to edit the interface eth0.

5) Deﬁne your Network Interface as described by your network administrator.

CLICK HERE

Do not change without to

contact Adeunis Support

Needs to be deﬁned by your

network administrator

Optional

IOT TOOLBOX - QUICK START GUIDE - V1.1.1

Page of 9

6) Click on « Save and Restart » to save the new network interface settings.

The Multitech Gateway is now rebooting and ready to be connected on the network of the company.

7) Once the gateway is rebooted, disconnect the Ethernet cable of gateway backpanel (E-NET) and connect the network cable of your

company.

Your Ethernet IoT Toolbox is now ready,

you can proceed to the activation of Adeunis devices

and monitor your data on your WebApp.

Note : In case of difﬁculty during the start-up, don’t ever press the « Reset » swith of the gateway. You would lose all the

settings of this one.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Adeunis RF Netzwerk-Hardware Handbücher

Adeunis RF

Adeunis RF COMFORT LwM2M Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung