ADJ FOCUS BEAM LED Bedienungsanleitung

User Instructions

FOCUS BEAM LED

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical prod-

ucts when they are not in use. To avoid power consumption in idle mode, disconnect all electrical

equipment from power when not in use. Thank you!

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and opera-

tion of this product.

DOCUMENT VERSION

Please check www.adj.com for the latest revision/update of this guide.

Date Document

Version

Software

Version

DMX

Channel

Modes

Notes

07/02/19 11.0.2 16 / 18 Initial Release

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installa-

tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance

with the included instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 2

Focus Beam LED Table of Contents

Introduction

Features I Warranty Registration

Safety Precautions

Overview

Installation

DMX Set Up

DMX Addressing

DMX Modes & Values

System Menu

Master-Slave Set Up

Dimmer Curve Chart

Static Gobos I Dimensional Drawings

Fuse Replacement I Multiple Unit Power Linking

Trouble Shooting I Cleaning

Warranty

Technical Specications

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 3

Focus Beam LED Introduction

Unpacking: Thank you for purchasing the Focus Beam LED by ADJ Products, LLC. Every unit has

been thoroughly tested and has been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all accessories necessary to operate the unit

has arrived intact. In the case damage has been found or parts are missing, please contact our toll free

customer support number for further instructions. Do not return this unit to your dealer without rst

contacting customer support.

Introduction: The Focus Beam LED is a DMX intelligent, moviing head, LED fixture. This xture can be

used in a stand alone mode or connected in a Master/Slave conguration. The fixture comes equipped

with 2 prisms (8 facet circular & 6 facet linear), focus, frost, 6 different dimming options with dimming

speed control. The Focus Beam LED has 2 DMX channel modes; 16 & 18.

This product is intended to be used by professionally trained personnel only and is not suitable

for private use.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

https://forums.adj.com/ with questions, comments or suggestions.

Parts: To purchase parts online visit http://parts.americandj.com

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-582-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-582-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Focus Beam LED Features

Focus Beam LED Warranty Registration

The Focus Beam LED carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,

you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-

tacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 4

• Individual Color and Gobo Wheels

• 13 Colors + White & Split Colors

• 14 Gobos + Open

• Electronic Dimming 0-100%

• DMX-512 protocol

• 3-Pin DMX Connections

• 2 DMX Channel Modes: 16 / 18

• Multiple Unit Power Linking (See page 25)

Included:

1 x powerCON Cable

1 x Safety Cable

2 x Omega Clamps

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 5

Focus Beam LED Safety Precautions

• DO NOT TOUCH the xture housing during operation. Turn OFF the power and allow approximately

15 minutes for the xture to cool down before servicing.

• DO NOT shake the xture, avoid brute force when installing and/or operating the xture.

• DO NOT operate the xture if the power cord has become frayed, crimped and/or damaged. If the

power cord is damaged, replace immediately with a new one of similar power rating.

• DO NOT Do not attempt to remove or break o the ground prong from the electrical cord. This

prong is used to reduce the risk of electrical shock and re in case of an internal short.

• DO NOT attempt to operate this unit, if it becomes damaged.

• DO NOT spill water or other liquids into or on to your unit.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

• Disconnect from main power before making any type of connection.

• DO NOT block any air ventilation slots. All fan and air inlets must remain clean and never blocked.

Allow approx. 6” (15cm) between xture and other devices or a wall for proper cooling.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• During the initial operation of this xture, a light smoke or smell may emit from the interior of the

xture. Thsi is a normal process and is caused by excess paint in the interior of the casing burning

o from the heat. This will decrease gradually over time.

• DO NOT remove the cover under any conditions. There are no user serviceable parts inside.

• When installing xture in a suspended enviroment, always use mounting hardware that is no less

than M10 x 25mm, and always install xture with an appropriately rated safety cable.

• Never operate this unit when it’s cover is removed.

• Never plug this unit in to a dimmer pack

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 25

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the fixture.

C. The fixture has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a marked change in performance.

E. The fixture has fallen and/or subjected to extreme handling.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 6

Focus Beam LED Safety Precautions

POTENTIAL INTERNAL FIXTURE DAMAGE FROM EXTERNAL SOURCES OF LIGHT BEAMS

External sources of light beams from direct sunlight, lighting moving head xtures, and lasers, which

are focused directly towards the exterior housing and/or penetrate the front lens opening of ADJ

lighting xtures, can cause severe internal damage including burning to optics, dichroic color lters,

glass and metal gobos, prisms, animation wheels, frost lters, iris, shutters, motors, belts, wiring,

discharge lamps, and LEDs.

This issue is not specic only to ADJ lighting xtures, it is a common issue with lighting xtures

from all manufacturers. Although there is no true way to fully prevent this issue from happening, the

guidelines below can prevent any potential damage from occurring if followed. Contact ADJ Service

for more details.

DO NOT EXPOSE THE FIXTURE AND/OR FRONT LENS OPENING TO LIGHT BEAMS FROM DIRECT

SUNLIGHT, OTHER LIGHTING MOVING HEAD FIXTURES, AND LASERS WHILE UNPACKING,

INSTALLATION, USE, AND EXTENDED IDLE TIMES OUTDOORS.

DO NOT FOCUS A LIGHT BEAM FROM ONE LIGHTING FIXTURE DIRECTLY TOWARDS ANOTHER.

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 7

FOCUS BEAM LED

Focus Beam LED Overview

Service Port

LED Display

Mode Button

Up Button

Down Button

Left Button

Right Button

Enter Button

powerCON In

Fuse Holder

3-Pin XLR Out

3-Pin XLR In

powerCON Out

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 8

Focus Beam LED Installation

Screw one clamp each via a M12 screw and nut into the Omega bracket. Insert the quick-lock fasteners

of the Omega holder’s into the respective holes on the bottom of the Focus Beam LED. Tighten the

quick-lock fasteners fully clockwise. Always use and install the supplied safety cable as a safety

measure to prevent accidental damage and/or injury in the event the clamp fails. Pull the safety

cable through the openings located on the base plate and over the trussing system or a safe xation

spot. Insert the end in the carabine and tighten the safety screw. Note: Never use the carrying handles

for secondary attachment.

NOTICE: When installing the unit, the trussing or area of installation must be able to hold 10 times

the weight without any deformation. The suitable enviromental temperature for this lighting xture is

between -25˚C to 45˚ C. Do not place this lighting xture in an enviroment where the temperatures

are under or above the temperatures stated above. This will allow the xture to run at its best and

help prolong the xture life. Be sure this xture is kept at least 12m (40ft) away from any ammable

materials (decoration etc.).

SAFETY CABLE

RIGGING POINT

OMEGA BRACKET

ATTACHMENT POINTS

ADJ Products, LLC - www.adj.com - Focus Beam LED User Manual Page 9

Focus Beam LED DMX Set Up

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of commu-

nication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions

from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture

via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only

have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufactures to be

linked together and operate from a single controller, as long as all xtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a fixture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Focus Beam LED can be controlled

via DMX-512 protocol. The Focus Beam LED has 2 DMX channel modes. The DMX address is set on the

front panel of the Focus Beam LED. Your unit and your DMX controller require a standard 3-pin XLR connec-

tor for data input and data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making

your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable

may be purchased at almost all pro lighting stores). Your cables should be made

with a male and female XLR connector on either end of the cable. Also remember

that DMX cable must be daisy chained and cannot be split.

Figure 1

Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a

short circuit and erratic behavior.

DMX512 IN

3-PIN XLR

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

SOUND

REMOTE

CONTROL

INPUT

POWER

INPUT OUTPUT

DMX512

DMX+,DMX-,COMMON

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.

DMX +

DMX -

COMMON

DMX512 OT

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket XLR Pin Conguration

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Andere Handbücher für FOCUS BEAM LED

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ ELEMENT H6 FC Bedienungsanleitung

ADJ

ADJ VIZI BEAM 5RX Bedienungsanleitung

ADJ

ADJ MDF2-9SYS Bedienungsanleitung

ADJ

ADJ PinPoint Gobo COLOR Bedienungsanleitung

ADJ

ADJ ENCORE PROFILE PRO WW Bedienungsanleitung

ADJ

ADJ Encore Profile 1000 WW Bedienungsanleitung

ADJ

ADJ ELEMENT HEXIP Bedienungsanleitung

ADJ

ADJ MDF2PSUX117 Benutzerhandbuch

ADJ

ADJ HYDRO WASH X7 Bedienungsanleitung

ADJ

ADJ DMX OPERATOR 384 Bedienungsanleitung

ADJ

ADJ M-101HD Bedienungsanleitung

ADJ

ADJ FS3000LED Bedienungsanleitung

ADJ

ADJ ADJ FLAT PAR TRI18X Bedienungsanleitung

ADJ

ADJ Flat Par Tri18 Bedienungsanleitung

ADJ

ADJ UV Panel HP Bedienungsanleitung

ADJ

ADJ SABER SPOT RGBW Bedienungsanleitung

ADJ

ADJ M-1616 Bedienungsanleitung

ADJ

ADJ 7P HEX IP Bedienungsanleitung

ADJ

ADJ StarTec Series Bedienungsanleitung

ADJ

ADJ PinPoint Gobo COLOR Bedienungsanleitung

ADJ

ADJ ENCORE BURST UV IP Bedienungsanleitung

ADJ

ADJ Vizi BSW 300 Bedienungsanleitung

ADJ

ADJ LINK Bedienungsanleitung

ADJ

ADJ H20 IR Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung