ADJ ELEMENT HEXIP Bedienungsanleitung

User Instructions

ELEMENT HEXIP

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products

when they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment

from power when not in use. Thank you!

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be

trademarks or registered trademarks of their respective companies and are hereby acknowledged.

All non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of

their respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, unsucient and negligent assembly, installation, rigging, and operation

of this product.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

FCC RADIO FREQUENCY INTERFERENCE WARNINGS & INSTRUCTIONS

This product has been tested and found to comply with the limits as per Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installa-

tion. This device uses and can radiate radio frequency energy and, if not installed and used in accordance

with the included instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this device does cause harmful

interference to radio or television reception, which can be determined by turning the device off and on, the

user is encouraged to try to correct the interference by one or more of the following methods:

· Reorient or relocate the device.

· Increase the separation between the device and the receiver.

· Connect the device to an electrical outlet on a circuit different from which the radio receiver is

connected.

· Consult the dealer or an experienced radio/TV technician for help.

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this document

may be available online.

Please check www.adj.com for the latest revision/update of this manual before beginning

installation and/or programming.

09/11/17 1.2 1.00 6/7/8/11/12 ETL Version

11/07/18 1.4 1.06 No Change Display Lock

IR Remote Functions Updated

03/21/19 Service Port Added

Date Document

Version

Software

Version > DMX Channel

Mode Notes

1.6 N/C No Change

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 2

Element HEXIP Table of Contents

Introduction

Features I Warranty Registration I Installation

Safety Precautions

Battery Precautions I Battery Status & Charging

IP Notice

Overview

DMX Addressing

DMX Control

DMX Modes

Color Macro Chart

System Menu

Operating Instructions

WiFly Set Up I WiFly Master-Slave Set Up

UC IR & Airstream Control

Dimmer Curve Chart

Dimensional Drawings

Fuse Replacement I Trouble Shooting I Cleaning

Warranty

Technical Specications

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 3

Element HEXIP Introduction

Unpacking: Thank you for purchasing the Element HEXIP by ADJ Products, LLC. Every Element

HEXIP has been thoroughly tested and has been shipped in perfect operating condition. Carefully

check the shipping carton for damage that may have occurred during shipping. If the carton appears

to be damaged, carefully inspect your xture for any damage and be sure all accessories necessary

to operate the unit has arrived intact. In the case damage has been found or parts are missing, please

contact our toll free customer support number for further instructions. Do not return this unit to your

dealer without rst contacting customer support.

Introduction: The Element HEXIP is a IP rated, rechargeable lithium battery powered, DMX intelligent,

LED par fixture with ADJ’s WiFly TransCeiver with wireless DMX built-in. This unit gives you the freedom to

set up your fixture where ever you wish without the restrictions of power or DMX cabling. This xture

can be used in a stand alone mode or connected in a Master/Slave conguration. This unit has five oper-

ating modes: Auto mode (color change, color fade, color change and fade combination), RGBWA+UV

Dimmer mode, Static Color mode, and DMX control mode. To optimize the performance of this product,

please read these operating instructions carefully to familiarize yourself with the basic operations of

this unit. These instructions contain important safety information regarding the use and maintenance

of this unit. Please keep this manual with the unit, for future reference.

Customer Support: Contact ADJ Service for any product related service and support needs. Also visit

forums.adj.com with questions, comments or suggestions.

Parts: To purchase parts online visit http://parts.americandj.com

ADJ SERVICE USA - Monday - Friday 8:00am to 4:30pm PST

Voice: 800-322-6337 | Fax: 323-832-2941 | [email protected]

ADJ SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET

Voice: +31 45 546 85 60 | Fax: +31 45 546 85 96 | [email protected]

ADJ PRODUCTS LLC USA

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands

+31 (0)45 546 85 00 | Fax +31 45 546 85 99

www.adj.eu | [email protected]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000

+52 (728) 282-7070

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufactures warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

Element HEXIP Features

Element HEXIP Warranty Registration

Element HEXIP Installation

The Element HEXIP carries a 2 year limited warranty. Please fill out the enclosed warranty card to

validate your purchase. All returned service items whether under warranty or not, must be freight pre-

paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on

the outside of the return package. A brief description of the problem as well as the R.A. number must

also be written down on a piece of paper included in the shipping carton. If the unit is under warranty,

you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by con-

tacting our customer support team on our customer support number. All packages returned to the

service department not displaying a R.A. number on the outside of the package will be returned to the

shipper.

The unit should be mounted using a mounting clamp (not provided), axing it to the mounting

bracket that is provided with the unit. Always ensure that the unit is rmly xed to avoid vibration

and slipping while operating. Always ensure that the structure to which you are attaching the unit is

secure and is able to support a weight of 10 times the unit’s weight. ALWAYS use safety cables that

can hold 12 times the weight of the unit when installing the xture.

This equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of people’s grasp.

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 4

• Five Operating Modes

• Electronic Dimming 0-100%

• RGBWA+UV Color Mixing

• 5 Selectable Dimming Curves

• 63 Color Macros

• Built in Microphone

• DMX-512 protocol

• 5 DMX Channel Modes: 6 Channel Mode, 7 Channel Mode, 8 Channel Mode, 11 Channel Mode, &

12 Channel Mode

• Rechargeable Lithium Battery

• Built-In ADJ’s WiFly TransCeiver Wireless DMX

• ADJ UC IR & Airstream IR compatible

Incuded Accessories:

1 x I.E.C. power cable

1 x UC IR Remote Control

1 x Airstream IR Transmitter

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 5

Element HEXIP Safety Precautions

NOT FOR RESIDENTIAL/HOUSE HOLD USE

NON DESTINÉ À UN USAGE DOMESTIQUE

SUITABLE FOR DAMP LOCATIONS

CONVIENT AUX EMPLACEMENTS HUMIDES

• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture

• Do not attempt to operate this unit if the power cord has been frayed or broken. Do not attempt to

remove or break o the ground prong from the electrical cord. This prong is used to reduce the risk

of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when it’s housing is removed.

• Never plug this unit in to a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm)

between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point they exit from the unit.

• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 25

for cleaning details.

• Heat -The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. The appliance does not appear to operate normally or exhibits a marked change in performance.

C. The fixture has fallen and/or subjected to extreme handling.

Element HEXIP Safety Precautions

RISK GROUP 3 - RISK OF EXPOSURE TO ULTRAVIOLET (UV) RADIATION!

FIXTURE EMITS HIGH INTENSITY ULTRAVIOLET (UV) LIGHT FROM THE UV LED.

WEAR PROPER EYE AND SKIN PROTECTION.

AVOID PROLONGED PERIODS OF EXPOSURE TO THE UV LED.

AVOID WEARING WHITE COLOR CLOTHING AND/OR USING (UV) PAINTS ON SKIN.

AVOID DIRECT EYE AND/OR SKIN EXPOSURE AT DISTANCES SHORTER THAN 11 feet (3.3m).

DO NOT OPERATE FIXTURE WITH DAMAGED OR MISSING EXTERNAL COVER.

DO NOT LOOK DIRECTLY INTO THE (UV) LIGHT AND/OR VIEW (UV) LIGHT DIRECTLY WITH

OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.

INDIVIDUALS SUFFERING FROM A RANGE OF EYE CONDITIONS, SUNLIGHT EXPOSURE

DISORDERS, OR INDIVIDUALS USING PHOTOSENSITIVE MEDICATION, MAY RECEIVE

DISCOMFORT IF EXPOSED TO THE ULTRAVIOLET (UV) LIGHT EMITTED FROM THIS FIXTURE.

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 6

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 7

Element HEXIP Battery Precautions

1. Handling of Batteries

1.1 Do Not Short Circuit the Battery

Try to never short circuit the battery. It generates a very high current which could cause the battery

to overheat which may result in electrolyte gel leakage, harmful fumes, or explosion. The LIR tabs

may easily short-circuit by placing them on conductive surface. A short circuit may lead to heat build

up and damage of the battery. An appropriate circuitry with PCM is employed to protect accidental

short circuit of the battery pack.

1.2 Mechanical shock

Droping the unit, impact hit, bending, etc. may cause failure or shortend life of the LIR battery.

3. Other

3.1 Battery connection

1). Direct soldering of wire leads or devices to the battery is strictly prohibited.

2). Lead tabs with pre-soldered wiring shall be spot welded to the batteries. Direct soldering may

cause damage of components, such as separator and insulator, by heat build up.

3.2 Prevention of short circuit within a battery pack

There is enough insulation layers between wiring and the batteries to provide extra safety protection.

The battery pack is constructed in a way that no short circuit will occur which may cause smoke or

re.

3.3 Do No Disassemble the Batteries

1). Never disassemble the batteries.

Doing this may cause a internal short circuit in the battery, which may lead to harmful fumes, re,

explosion, or other problems.

2). Electrolyte Gel is harmful

Electrolyte Gel should not leak from the LIR battery. Should the electrolyte gel come into contact

with the skin or eyes, ush the area of contact immediately with fresh water and seek medical atten-

tion immediately.

3.4 Do Not Expose the Battery to Heat or Fire

Never incinerate or dispose of the batteries in re. This may cause an explosion, which would be

very dangerous.

3.5 Do Not Expose the Battery to water or liquids

Never soak/drop the batteries in liquids such as water, seawater, drinks such as soft drinks, juices,

coee or other.

3.6 Battery Replacement

For battery replacement please contact ADJ customer support (800) 322-6337.

3.7 Do Not use a damaged Battery

The battery could be damaged during shipping, caused by shock. Should the battery be found dam-

aged, including damages to the plastic casing of the battery, deformation of the battery package,

smelling of an electrolyte, or leakage of the electrolyte gel, or other, DO NOT use the battery. A bat-

tery with a odor of electrolyte or a gel leakage should be placed away from re to avoid re or explo-

sion.

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 8

Element HEXIP Battery Precautions

4. Battery Storage

When storing the battery, it should be stored at room temperature, with a charge of at least 50%. We

recommend that during long periods of storage that the battery be charged every 6 months. Doing

this will prolong the life of the battery and will also make sure that the battery charge does not fall

below the 30% mark.

5. Other Chemical Reaction

Because batteries utilize a chemical reaction, battery performance will deteriorate over time even if

stored for a long period of time without being used. In addition, if the various usage conditions such

as charge, discharge, ambient temperature, etc. are not maintained within the specied ranges, the

life expectancy of the battery maybe shortened or the device in which the battery is used may be

damaged by electrolyte gel leakage. If the batteries cannot maintain a charge for long periods of

time, even when they are charged correctly, this may indicate it is time to change the battery.

6. Battery Disposal

Please dispose of battery according to local regulations.

Battery Status:

This function is used to check the life status of the battery.

Plug the fixture in and press the MODE button until “bXXX” is displayed. “XXX” represents the current

battery life. The number that is displayed is the remaining battery life. If “b---” is displayed, it means

that you are running the unit on AC power. Please do not let the battery fully die, this severly

shortens the life of the battery.

NOTE: When the battery life is below 30% the battery percentage will flash. At 15% power the fixture

will shut off.

NOTE: When using battery power, after 20 seconds of inactivity, the display will revert back to

the battery life display.

Battery Recharge: To recharge the battery, plug the supplied I.E.C. cord into the I.E.C. input on the

side of the unit and plug the other end into a matching power supply. It takes about 4 hours to reach

full charge (with the power o). The display will STOP ashing when the unit reaches 100% charge.

Note: When unplugging the unit from charging and then applying power via battery, there will

be a minimal charge drop.

For a faster recharge, turn the Load setting to “O” and turn the battery “On”. See “Load Setting” on

page 17.

Element HEXIP Battery Status & Charging

ADJ Products, LLC - www.adj.com - Element HEXIP User Manual Page 9

Element HEXIP IP Notice

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ HYDRO BEAM X1 Bedienungsanleitung

ADJ

ADJ FOCUS BEAM LED Bedienungsanleitung

ADJ

ADJ ENCORE BURST UV IP Bedienungsanleitung

ADJ

ADJ DOTZ MATRIX Bedienungsanleitung

ADJ

ADJ UV 72IP Bedienungsanleitung

ADJ

ADJ THEATRIX PRO 48 LED Bedienungsanleitung

ADJ

ADJ Inno Pocket Spot Pearl Bedienungsanleitung

ADJ

ADJ ENCORE BURST 100 IP Bedienungsanleitung

ADJ

ADJ ENCORE PROFILE MINI COLOR Bedienungsanleitung

ADJ

ADJ Mega Go Bar 50 Gebrauchs- und Pflegehandbuch

ADJ

ADJ Mega GO Bar 50 RGBA Bedienungsanleitung

ADJ

ADJ 6-PACK SKB CASE Bedienungsanleitung

ADJ

ADJ InnoRollLED Bedienungsanleitung

ADJ

ADJ ENCORE FR150Z Bedienungsanleitung

ADJ

ADJ STARTEC BOOM BOX FX2 Bedienungsanleitung

ADJ

ADJ H20 IR Bedienungsanleitung

ADJ

ADJ XPress LED Bedienungsanleitung

ADJ

ADJ PAR Z120 RGBW Bedienungsanleitung

ADJ

ADJ ADJ FLAT PAR TRI18X Bedienungsanleitung

ADJ

ADJ ECO UV BAR PLUS IR Bedienungsanleitung

ADJ

ADJ M-101HD Bedienungsanleitung

ADJ

ADJ LTS COLOR Bedienungsanleitung

ADJ

ADJ ENCORE LP12Z IP Bedienungsanleitung

ADJ

ADJ LINK Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung