ADJ Mega GO Par64 PLUS Bedienungsanleitung

User Manual

MEGA GO PAR64 PLUS

Rev. 10/27/2022

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying prod-

uct names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection claimed

includes all forms and matters of copyrightable materials and information now allowed by statutory or

judicial law or hereinafter granted. Product names used in this document may be trademarks or regis-

tered trademarks of their respective companies and are hereby acknowledged. All non-ADJ Products,

LLC brands and product names are trademarks or registered trademarks of their respective compa-

nies.

ADJ Products, LLC and all afliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insufcient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn off all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

Unpacking: Thank you for purchasing the Mega Go Par64 Plus by ADJ Products, LLC. Every unit has

been thoroughly tested and has been shipped in perfect operating condition. Carefully check the ship-

ping carton for damage that may have occurred during shipping. If the carton appears to have been

damaged, carefully inspect your xture for any damage and be sure all equipment necessary to oper-

ate the unit has arrived intact. In the event that damage has been found or parts are missing, please

contact our toll free customer support number for further instructions. Please do not return this unit to

your dealer without contacting customer support rst.

Introduction: The ADJ Mega GO Par64 PLUS is a DMX intelligent, high powered LED par xture

which can be used in stand alone mode or connected in a Primary/Secondary conguration. It also

features ve operating modes: Sound Active mode, Auto mode, RGB + UV Dimmer mode, Static Color

mode, and DMX control mode. To optimize the performance of this product, please read these operat-

ing instructions carefully to familiarize yourself with the basic operations of this unit. These instructions

contain important safety information regarding the use and maintenance of this unit. Please keep this

manual with the unit for future reference.

Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up

help and to answer any questions should you encounter problems during your set up or initial operation.

You may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are

Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (323) 582-2650

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit parts.adj.com.

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as

doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service,

please contact ADJ Products, LLC.

PLEASE recycle the shipping carton when ever possible.

INTRODUCTIONINTRODUCTION

• Five Operating Modes

• Electronic Dimming 0-100%

• 5 Selectable Dimming Curves

• 64 Color Macros

• Built in Microphone

• DMX-512 protocol

• 3-Pin DMX Connection

• 5 DMX Modes: 4 Channel Mode, 5 Channel Mode, 6 Channel Mode, 9 Channel Mode, & 10

Channel Mode.

• ADJ LED RC2, ADJ UC IR, (Not Included) & Airstream IR compat- ible

• Power Cord Daisy Chain (see Power Cord Daisy Chain section of this manual)

The Mega Go Par64 Plus carries a 2 year (730 days) limited warranty. Please fill out the enclosed

warranty card to validate your purchase and warranty. You may also register your product online at

www.adj.com. The R.A. number must be clearly written on the outside of the return package. A brief

description of the problem as well as the R.A. number must also be written down on a piece of paper

included in the shipping carton. If the unit is under warranty, you must provide a copy of your proof of

purchase invoice. You may obtain an R.A. number by contacting our customer support team on our

customer support number. All packages returned to the service department not displaying an R.A.

number on the outside of the package will be returned to the shipper.

WARRANTY REGISTRATION

FEATURES

INSTALLATION

The unit should be mounted using a mounting clamp (not provided), affixing it to the mounting bracket

that is provided with the unit. Always ensure that the unit is firmly fixed to avoid vibration and slipping

during operation. Always ensure that the structure to which you are attaching the unit is secure and

is able to support at least 10 times the unit’s weight. Also, always use a safety cable that can hold 12

times the weight of the unit when installing the fixture.

The equipment must be installed by a professional, and it must be installed in a place where it is out

of the reach of the general public.

SAFETY PRECAUTIONS

• To reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in the event of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover for any reason. There are no user serviceable parts inside.

• Never operate this unit with the cover removed.

• Never plug this unit into a dimmer pack.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if it has been damaged in any way.

• This unit is intended for indoor use only, and use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to the point at which they exit from

the unit.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the

Cleaning section of this manual for cleaning details.

• Heat - The appliance should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power supply cord or plug have been damaged.

B. Objects have fallen onto, or liquids have been spilled into, the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in perfor-

mance.

BATTERY PRECAUTIONS

1. Handling of Batteries

1.1 Do Not Short Circuit the Battery

Never short circuit the battery, as doing so generates a very high current which could cause the bat-

tery to overheat, potentially resulting in electrolyte gel leakage, harmful fumes, or explosion. The LIR

tabs can be easily short-circuit when placed on a conductive surface. A short circuit may lead to heat

build up and battery damage. An appropriate circuitry with PCM is employed to protect against acci-

dental short circuit of the battery pack.

1.2 Mechanical shock

Dropping the unit, impacts, bending, etc. may cause failure or shortend life of the LIR battery.

2. Other

2.1 Battery connection

• Direct soldering of wire leads or devices to the battery is strictly prohibited.

• Lead tabs with pre-soldered wiring shall be spot welded to the batteries. Direct soldering may

cause heat buildup, which can damage components, such as the separator and the insulator.

2.2 Prevention of short circuit within a battery pack

There is enough insulation layers between wiring and the batteries to provide extra safety protec-

tion. The battery pack is constructed in such a way as to prevent any short circuit that could result in

smoke or re.

2.3 Do Not Disassemble the Batteries

• Never disassemble the batteries. Doing so may cause an internal short circuit in the battery, which

can result in harmful fumes, re, explosion, or other hazards.

• Electrolyte Gel is harmful! Electrolyte Gel should not leak from the LIR battery. Should the electro-

lyte gel come into contact with the skin or eyes, ush the area of contact immediately with fresh

water and seek medical attention immediately.

2.4 Do Not Expose the Battery to Heat or Fire

Never incinerate or dispose of the batteries in re. Doing so creates a serious explosion risk!

2.5 Do Not Expose the Battery to water or liquids

Never soak/drop the batteries in liquids, including fresh water, seawater, soft drinks, juices, coffee or

other beverages.

2.6 Battery Replacement

For battery replacement please contact ADJ customer support (323) 582-2650.

2.7 Do Not use a damaged Battery

Inspect the battery for damage that may have occurred during shipping. In the event that damage is

present, including but not limited to damage to the plastic casing of the battery, deformation of the

battery package, the presence of an electrolyte odor, or leakage of the electrolyte gel, DO NOT use

the battery. A battery with a odor of electrolyte or a gel leakage should be placed away from re to

avoid re or explosion.

3. Battery Storage

Store the battery at room temperature, with a charge of at least 50%. During long periods of storage,

it is recommended to charge the battery every 6 months. Doing so will prolong the life of the battery,

and will also ensure that the battery is ready for use.

4. Other Chemical Reactions

Because batteries utilize a chemical reaction, battery performance will deteriorate over time, even if

stored for a long period of time without being used. Additionally, if the various usage conditions such

as charge, discharge, ambient temperature, etc. are not maintained within the specied ranges, the

life expectancy of the battery may be shortened, or the device in which the battery is used may be

damaged by electrolyte gel leakage. If the batteries cannot maintain a charge for long periods of time,

even when they are charged correctly, this may indicate it is time to change the battery.

5. Battery Disposal

Please dispose of battery according to local regulations.

BATTERY PRECAUTIONS

DMX SETUP

Power Supply: The ADJ Mega GO Par64 PLUS contains an automatic voltage switch, which will

automatically sense the voltage when it is plugged into the power source. With this switch there is no

need to worry about the correct power voltage, and this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used as a form of communi-

cation between intelligent xtures and controllers. A DMX controller sends DMX data instructions from

the controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have a

DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be

linked together and operate from a single controller, as long as all xtures and the controller are

DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible

when linking several DMX xtures. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example, a xture assigned a DMX address of 1 may be placed

anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a xture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX Operation): The Mega GO Par64 PLUS can

be controlled via DMX-512 protocol, and features 5 selectable DMX modes, as detailed in the DMX

Traits section of this manual. The DMX address is set on the back panel of the Mega GO Par64

PLUS. Your unit and your DMX controller require a standard 3-pin XLR connector for data input and

data output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your own cables,

be sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro

lighting stores). Your cables should be made with a male XLR connector at one end and a female

XLR connector at the other. Also remember that DMX cable must be daisy chained and cannot be

split.

Figure 1

DMX SETUP

Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground

lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the

shield conductor to come into contact with the XLR’s outer casing. Grounding the shield could cause

a short circuit and erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-

nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is

connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted

in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable

terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-

mission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line by inserting an

adapter into the line. These adapters are readily available at most electronics stores. The chart below

details a proper cable conversion.

Conductor 5-Pin XLR Male (In)3-Pin XLR Female (Out)

Pin 1

Do Not Use

Pin 3

Pin 2

Pin 1

Pin 3

Pin 2

Not Used

Data True (+ signal)

Data Compliment (- signal)

Ground/Shield

3-Pin XLR to 5-Pin XLR Conversion

DMX512 IN

3-PIN XLR

DMX +

DMX -

COMMON

3-PIN XLR

Figure 2

Figure 3

1 Ground 1 Ground

XLR Male Socket

3 Hot

2 Cold 2 Cold

3 Hot

XLR Female Socket

Pin 3 = Data True (positive)

Pin 2 = Data Compliment (negative)

Pin 1 = Ground

Termination reduces signal errors and

avoids signal transmission problems

and interference. It is always advisable

to connect a DMX terminal, (Resistance

120 Ohm 1/4 W) between PIN 2 (DMX-)

and PIN 3 (DMX +) of the last fixture.Figure 4

System Menu: The display will lock after 30 seconds.To unlock, press and the MODE button

for 3 seconds.

LED Display On/Off:

To set the display press the MODE button until “dXX” is displayed. Use the UP or DOWN buttons to

select either:

• “don” = LED display on at all times.

• “doFF” = LED display shuts off after 10 seconds.

Please note, the display will turn off automatically after 10 seconds.

LED Display Inversion:

Follow these instructions to ip the display 180° so that the display can be read upside down.

1. Plug the xture in and press the MODE button until “dXX” is displayed. “XX” represents either “on”

or “oFF”.

2. Press the SET UP button until “Stnd” is displayed.

3. Press the UP or DOWN buttons to reverse the display 180°.

Operating Modes:

The Mega GO Par64 PLUS has ve selectable operating modes:

• RGB+UV Dimmer Mode - Choose one of the four colors to remain static, or adjust the intensity of

each color to make a custom color.

• Sound-Active mode - The unit will react to sound, chasing through the built in programs. There are

16 sound active modes.

• Auto Run Mode - In Auto Run mode, you can choose 1 of 16 color change modes, 1 of 16 color

fade modes, or a combo color change & fade mode.

• Static Color Mode - There are 64 colors to choose from.

• DMX control mode - This function will allow you to control each individual xtures traits with a

standard DMX 512 controller.

RGB+UV Dimmer Mode:

1. Plug the xture in and press the MODE button until the desired option is shown:

• When “r.XXX” is displayed, the unit is in Red dimming mode. Press the UP and DOWN buttons

to adjust intensity.

• When “G.XXX” is displayed, the unit is in Green dimming mode. Press the UP and DOWN but-

tons to adjust intensity.

• When “b.XXX” is displayed, the unit is in Blue dimming mode. Press the UP and DOWN buttons

to adjust intensity.

• When “u.XXX” is displayed, the unit is in UV dimming mode. Press the UP and DOWN buttons

to adjust intensity.

2. After you have adjusted the RGB & UV colors to create your desired color, you can then activate

strobing by pressing the SET UP button to enter the Flash (strobe) mode.

3. “FS.XX” will be displayed, indicating that the unit is in Flash mode. The Flash can be adjusted

between “FS.00” (ash off) to “FS.15” (fastest ash).

OPERATING INSTRUCTIONS

Andere Handbücher für Mega GO Par64 PLUS

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ ENTOUR ICE Bedienungsanleitung

ADJ

ADJ VIZI CMY300 Bedienungsanleitung

ADJ

ADJ Dotz Par Bedienungsanleitung

ADJ

ADJ ELEMENT H6 FC Bedienungsanleitung

ADJ

ADJ HEX206 Bedienungsanleitung

ADJ

ADJ LTS COLOR Bedienungsanleitung

ADJ

ADJ Gobo Motion LED Montageanleitung

ADJ

ADJ Vizi BSW 300 Bedienungsanleitung

ADJ

ADJ StarTec Series Bedienungsanleitung

ADJ

ADJ ENCORE BURST UV IP Bedienungsanleitung

ADJ

ADJ INNO POCKET ROLL Bedienungsanleitung

ADJ

ADJ XS 400 Bedienungsanleitung

ADJ

ADJ ENTOUR HAZE PRO Bedienungsanleitung

ADJ

ADJ FREQ Matrix Bedienungsanleitung

ADJ

ADJ SABER SPOT RGBW Bedienungsanleitung

ADJ

ADJ UB 12H Bedienungsanleitung

ADJ

ADJ Hydro Profile Bedienungsanleitung

ADJ

ADJ VIZI CMY300 Bedienungsanleitung

ADJ

ADJ VIZ870 Bedienungsanleitung

ADJ

ADJ COB CannOn Wash DW Bedienungsanleitung

ADJ

ADJ ENCORE BURST 200 Bedienungsanleitung

ADJ

ADJ UV Panel HP Bedienungsanleitung

ADJ

ADJ Eliminator Lighting FROST FX BAR W Bedienungsanleitung

ADJ

ADJ penta pix Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung