ADJ StarTec Series Bedienungsanleitung

User Manual

STARBURST

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 2

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 3

Unpacking: Thank you for purchasing the Starburst by ADJ Products, LLC. Every Starburst has been

thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping

carton for damage that may have occurred during shipping. If the carton appears to be damaged,

carefully inspect your xture for any damage and be sure all equipment necessary to operate the unit

has arrived intact. In the event damage has been found or parts are missing, please contact our toll-

free customer support number for further instructions. Please do not return this unit to your dealer

without contacting customer support rst.

Introduction: The Starburst is part of ADJ’s continuing pursuit for creating and upgrading aordable

intelligent xtures. The Starburst is a DMX intelligent centerpiece. This xture can be used as a stand

alone piece or connected in a Primary/Secondary conguration. The Starburst has 3 operating modes:

Sound Active, Show Mode, and DMX controlled. When using DMX control, the xture has 12 DMX

channels.

Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide help and

to answer any question should you encounter problems during your set up or initial operation. You

may also visit us on the web at www.adj.com for any comments or suggestions. Service Hours are

Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (800) 322-6337

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online, visit parts.adj.com.

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself,

doing so will void your manufacturer’s warranty. In the unlikely event your unit may require service

please contact ADJ Products, LLC.

Starburst General Information

Starburst General Instructions

Please carefully read and understand the instructions in this manual thoroughly before attempting

to operate this unit. These instructions contain important safety information regarding the use and

maintenance of this unit. Please keep this manual with the unit, for future reference.

Starburst Main Features

• Bright 15W 5-in-1 LED RGBWYP

• DMX-512 Compatible: 12 DMX Channels

• Stand Alone or Primary-Secondary Set Up

• 3 Operating Modes - Sound Active, Show Mode, & DMX Controlled

• Power Cord Daisy Chain up to 20 Fixture (See Power Cord Daisy Chain section)

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 4

Starburst Product Registration

The Starburst carries a 1 Year limited warranty. Please fill out the enclosed warranty card to validate

your purchase. All returned service items, whether under warranty or not, must be freight pre-paid

and accompany a return authorization (R.A.) number. If the unit is under warranty, you must provide

a copy of your proof of purchase invoice. Please contact ADJ customer support for an R.A. number.

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 5

Starburst Safety Precautions

• To reduce the risk of electrical shock or re, do not expose this unit to rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Do not attempt to remove or break o the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and re in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Never operate this unit when its cover is removed.

• Never plug this unit into a dimmer pack

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if has been damaged.

• This unit is intended for indoor use only, use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to cords at plugs, convenience

receptables, and the point where they exit from the appliance.

• Cleaning - The xture should be cleaned only as recommended by the manufacturer. See Clean-

ing section for cleaning details.

• Heat - The appliance should be situated away from heat sources such as radiators, heat regis-

ters, stoves, or other appliances (including ampliers) that produce heat.

• The xture should be serviced by qualied service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into, the appliance.

C. The appliance has been exposed to rain or water.

D. The appliance does not appear to operate normally or exhibits a marked change in perfor-

mance.

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 6

Power Supply: The ADJ Starburst contains an automatic voltage switch, which will auto sense the

voltage when it is plugged into the power source. With this switch there is no need to worry about

the correct power voltage, this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and

controller manufacturers as a form of communication between intelligent fixtures and controllers. A

DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as

serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals locat-

ed on all DMX fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufactures to be

linked together and operate from a single controller, as long as all fixtures and the controller are DMX

compliant. To ensure proper DMX data transmission, when using several DMX fixtures try to use

the shortest cable path possible. The order in which fixtures are connected in a DMX line does not

influence the DMX addressing. For example, a fixture assigned a DMX address of 1 may be placed

anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. Therefore, the first

fixture controlled by the controller could be the last fixture in the chain. When a fixture is assigned a

DMX address of 1, the DMX controller knows to send data assigned to address 1 to that unit, no mat-

ter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Primary/Secondary Operation): The

Starburst can be controlled via DMX-512 protocol. The Starburst has 12 DMX channels. The DMX

address is set electronically using the controls on the front panel of the unit. Your unit and your DMX

controller require an approved DMX-512 110 Ohm Data cable for data input and data output (Figure

1). We recommend Accu-Cable DMX cables. If you are making your own cables, be sure to use stan-

dard 110-120 Ohm shielded cable (This cable may be purchased at almost all professional sound

and lighting stores). Your cables should be made with a male XLR connector on one end of the cable

and a female XLR connector on the other. Also remember that DMX cable must be daisy chained

and cannot be split.

Starburst Set Up

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 7

Notice: Be sure to follow figures two and three when making your own cables. Do not use the

ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug

or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield

could cause a short circuit and erratic behavior.

Starburst Set Up

Special Note: Line Termination. When longer runs of cable are used, you may need to use a ter-

minator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor

which is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is

inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a

cable terminator (ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-

mission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When insert-

ing standard 5-pin data cables in to a 3-pin line, a cable adaptor must be used. These adaptors are

readily available at most electric stores. The chart below details a proper cable conversion.

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 8

Starburst System Menu

DMX Address

Show Mode

Primary

Secondary 1

Secondary 2

Sound State

Sound Sense

Pri.Sec.

Blackout

Last State

Manual Control

LED

Fixture Hours

Display Inversion

Software Version

Reset

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 9

System Menu: When making adjustments press ENTER to confirm your setup. To exit without

making any adjustments press the MODE button. After 10 seconds, the display will return to

the DMX address setting. Your operating mode will still continue to run despite the display

showing the DMX address setting. The display will lock after 30 seconds, press the MODE but-

ton for 3 seconds to unlock.

Addr - DMX Address Setting. See DMX Control section for more information on DMX Control.

To run DMX mode, you must first turn AUTO off. Please see AUTO below for instructions on

how to turn AUTO mode off.

1. Press the either the MODE button until “Addr” is displayed, and press ENTER.

2. Press the UP or DOWN buttons to find your desired address. Press ENTER to set your desired

DMX address.

SCNd - This will let you set the unit as a primary in a primary/secondary configuration.

1. Press the MODE button until “SCnd” is displayed. Press ENTER. Either “PRI”, “SEC1”, or “SEC2”

will be displayed.

2. Press the UP or DOWN buttons until your desired setting is displayed, press ENTER to confirm.

ShNd - Show Mode.

1. Press the MODE button until “ShNd” is displayed, and press ENTER.

2. The unit will now operate in pre-programmed show mode.

SoSe - Sound sensitivity adjustment.

1. Press the MODE button until “SoSe” is displayed, and press ENTER.

2. Press the UP or DOWN buttons to adjust the sound sensitivity. Press ENTER when you have

reached your desired setting.

dNSt - In the event that the DMX signal is lost, the fixture will default to the operating mode

selected in this setting menu.

1. Press the MODE button until “dNSt” is displayed, and press ENTER.

2. Press the UP and DOWN buttons to select the desired setting.

A. “PrSe” - Defaults to primary/secondary mode. The unit will behave as defined in the primary/

secondary configuration menu (“SCNd”).

B. “bLNd” - Defaults to standby mode.

C. “LASt” - Defaults to most recently used settings.

3. Press ENTER to confirm your selection.

Starburst System Menu

ADJ Products, LLC - www.adj.com - Starburst User Manual Page 10

Starburst System Menu

NAnu - Manual Control Mode. Allows the user to manually set the following from 0 to 255:

1. Press the MODE button until “NAnu” is displayed, and press ENTER.

2. Use the UP and DOWN buttons to scroll through the various functions. Once you have found your

desired function, press ENTER to select. Available functions are:

A. “rEd” - Red

B. “GrEE” - Green

C. “bLuE” - Blue

D. “UhIt” - White

E. “PurP” - Purple

F. “dINN” - Dimmer

G. “Stro” - Strobe

H. “Noto” - Motor Control

3. Use the UP and DOWN buttons to adjust the values for the selected function. Available values

range from 0 to 255. Press the MENU button to exit to the main menu.

LEd - Allows the user to set the LED display screen to turn o after 10 seconds of inactivity.

1. Press the MODE button until “LEd” is displayed, and press ENTER.

2. Use the UP and DOWN buttons to toggle between ON and OFF. ON keeps the display screen on

at all times, while OFF will turn the screen o after 10 seconds of inactivity.

dISP - Select the orientation of the display screen.

1. Press the MODE button until “dISP” is displayed, and press ENTER.

2. Use the UP and DOWN button to toggle between “dISP” (upright display orientation) and “dSIP”

(inverted display orientation).

3. Press ENTER to conrm your selection.

FhrS - Display xture hours.

1. Press the MODE button until “FhrS” is displayed, and press ENTER.

2. The screen will now display the number of operating hours.

vEr - Display software version.

1. Press the MODE button until “vEr” is displayed, and press ENTER.

2. The screen will display the current software version.

rSEt - Use this function to restore the unit to its factory settings.

1. Press the MODE button until “rSEt” is displayed, and press ENTER.

2. The unit will now reset to the default factory settings.

Andere Handbücher für StarTec Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ADJ DJ-Equipment Handbücher

ADJ

ADJ VIZI CMY300 Bedienungsanleitung

ADJ

ADJ Encore Profile 1000 WW Bedienungsanleitung

ADJ

ADJ UV 72IP Bedienungsanleitung

ADJ

ADJ IKON IR Bedienungsanleitung

ADJ

ADJ Mega GO Bar 50 RGBA Bedienungsanleitung

ADJ

ADJ ENCORE PROFILE PRO WW Bedienungsanleitung

ADJ

ADJ Vision Series Bedienungsanleitung

ADJ

ADJ 18P HEX IP Bedienerhandbuch

ADJ

ADJ Focus Spot 5Z Bedienungsanleitung

ADJ

ADJ ENCORE BURST 200 Bedienungsanleitung

ADJ

ADJ 6-PACK SKB CASE Bedienungsanleitung

ADJ

ADJ ELEMENT HEXIP Bedienungsanleitung

ADJ

ADJ EVS3 Bedienungsanleitung

ADJ

ADJ ENCORE LP12Z IP Bedienungsanleitung

ADJ

ADJ ENCORE PROFILE PRO COLOR Bedienungsanleitung

ADJ

ADJ WOLFMIX WMX1 Bedienungsanleitung

ADJ

ADJ 7P HEX IP Bedienungsanleitung

ADJ

ADJ Par Z100 3K Bedienungsanleitung

ADJ

ADJ HEX700 Bedienungsanleitung

ADJ

ADJ ENCORE FR50Z Bedienungsanleitung

ADJ

ADJ LINK Bedienungsanleitung

ADJ

ADJ ENCORE BURST RGBW IP Bedienungsanleitung

ADJ

ADJ XS 400 Bedienungsanleitung

ADJ

ADJ WiFly NE1 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung