ADJ INNO POCKET SCAN Bedienungsanleitung

User Manual

INNO POCKET SCAN

Rev. 02/2021

instructions herein are subject to change without notice. ADJ Products, LLC logo and identifying

product names and numbers herein are trademarks of ADJ Products, LLC. Copyright protection

claimed includes all forms and matters of copyrightable materials and information now allowed by

statutory or judicial law or hereinafter granted. Product names used in this document may be trade-

marks or registered trademarks of their respective companies and are hereby acknowledged. All

non-ADJ Products, LLC brands and product names are trademarks or registered trademarks of their

respective companies.

ADJ Products, LLC and all aliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic

loss associated with the use or reliance of any information contained within this document, and/or as

a result of the improper, unsafe, insucient and negligent assembly, installation, rigging, and opera-

tion of this product.

Europe Energy Saving Notice

Energy Saving Matters (EuP 2009/125/EC)

Saving electric energy is a key to help protecting the enviroment. Please turn o all electrical products when

they are not in use. To avoid power consumption in idle mode, disconnect all electrical equipment from power

when not in use. Thank you!

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 2

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 3

Unpacking: Thank you for purchasing the Inno Pocket Scan by ADJ Products, LLC. Every Inno Pocket

Scan has been thoroughly tested and has been shipped in perfect operating condition. Carefully

check the shipping carton for damage that may have occurred during shipping. If the carton appears

to be damaged, carefully inspect your xture for any damage and be sure all equipment necessary

to operate the unit has arrived intact. In the event that damage has been found or parts are missing,

please contact our toll free customer support number for further instructions. Please do not return this

unit to your dealer without contacting customer support rst.

Introduction: The Inno Pocket Scan is a mini DMX intelligent LED scanner. The Inno Pocket Scan has

6 DMX channels. The Inno Pocket Scan has three operating modes: sound active mode, show mode,

and DMX control. The Inno Pocket Scan can operate as a stand alone xture or in a Primar/Secondary

conguration. For best results use fog or special eects smoke to enhance the projections.

Customer Support: ADJ Products, LLC provides a toll free customer support line, to provide set up

help and to answer any questions should you encounter problems during your set up or initial opera-

tion. You may also visit us on the web at www.adj.com for any comments or suggestions. Service

Hours are Monday through Friday 8:00 a.m. to 4:30 p.m. Pacic Standard Time.

Voice: (323) 582-2650

Fax: (323) 582-2941

E-mail: [email protected]

To purchase parts online visit parts.adj.com.

Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or

moisture.

Warning! This may cause severe eye damage. Never look directly into the light source!

Inno Pocket Scan General Information

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 4

Inno Pocket Scan General Instructions

To optimize the performance of this product, please read these operating instructions carefully to

familiarize yourself with the basic operations of this unit. These instructions contain important safety

information regarding the use and maintenance of this unit. Please keep this manual with the unit for

future reference.

• 6 DMX Channels

• 3 Operating Modes - Sound Active Mode, Show Mode, & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• 12 Preprogrammed Shows

• 8 fixed Gobos/Colors + Spot/White

• Power Cord Daisy Chain (See Power Cord Daisy Chain section of this manual)

• UC IR Compatiable (Sold Separately)

The Inno Pocket Scan carries a 2 year (730 days) limited warranty. Please fill out the enclosed war-

ranty card to validate your purchase and warranty. You may also register your product online at

www.adj.com. All returned service items, whether under warranty or not, must be freight pre-paid

and accompanied by a return authorization (R.A.) number. If the unit is under warranty, you must

provide a copy of your proof of purchase invoice. Please contact ADJ customer support for an R.A.

number.

Inno Pocket Scan Warranty Registration

Inno Pocket Scan Features

Inno Pocket Scan Handling Precautions

Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as

doing so will void your manufacturer’s warranty. In the unlikely event that your unit requires service,

please contact ADJ Products, LLC.

During operation the housing may become extremely hot. Avoid touching the unit with bare hands

while in use.

ADJ will not accept any liability for any resulting damages caused by the non-observance of this

manual or any unauthorized modification to this unit.

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 5

Inno Pocket Scan Safety Precautions

For Your Own Personal Safety, Please Read and Understand This Manual In Its Entirety Before

You Attempt To Install Or Operate This Unit!

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to operate this unit if the power cord is frayed or broken.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover for any reason. There are no user serviceable parts inside.

• Never operate this unit with the cover removed.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if it has been damaged in any way.

• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them. Particular attention should be paid to cords at plugs, conve-

nience receptacles, and the point where they exit from the appliance.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the

Cleaning section of this manual for details.

• Heat - This fixture should be situated away from heat sources such as radiators, heat registers,

stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen onto, or liquid has been spilled into, the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits a marked change in perfor-

mance.

Inno Pocket Scan Set Up

Power Supply: The ADJ Inno Pocket Scan contains an automatic voltage switch, which will auto-

matically sense the voltage when it is plugged into a power source. With this switch there is no need

to worry about the correct power voltage, and this unit can be plugged in anywhere.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and

controller manufacturers as a form of communication between intelligent xtures and controllers. A

DMX controller sends DMX data instructions from the controller to the xture. DMX data is sent as

serial data that travels from xture to xture via the DATA “IN” and DATA “OUT” XLR terminals locat-

ed on all DMX xtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of dierent manufacturers to be

linked together and operate from a single controller, as long as all xtures and the controller are

DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path pos-

sible when linking multiple xtures. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example: a xture assigned a DMX address of 1 may be placed

anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a xture is

assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address 1 to that

unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX and Primary/Secondary Operation): The Inno

Pocket Scan can be controlled via DMX-512 protocol. The Inno Pocket Scan is a 6 channel DMX

unit. The DMX address is set electronically using the controls on the side panel of the unit. Your unit

and your DMX controller require a approved DMX-512 110 Ohm Data cable for data input and data

output (Figure 1). We recommend Accu-Cable DMX cables. If you are making your own cables, be

sure to use standard 110-120 Ohm shielded cable (This cable may be purchased at almost all pro-

fessional sound and lighting stores). Your cables should be made with a male and female XLR con-

nector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot

be split.

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 6

Notice: Be sure to follow gures two and three when making your own cables. Do not use the

ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug

or allow the shield conductor to come in contact with the XLR cable’s outer casing. Grounding the

shield could cause a short circuit and erratic behavior.

Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-

nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which

is connected between pins 2 and 3 of a male XLR connector (DATA+ and DATA-). This unit is inserted

in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable

terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.

5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA trans-

mission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line. When insert-

ing standard 5-pin data cables in to a 3-pin line a cable adaptor must be used. These adaptors are

readily available at most electronics stores. The chart below details a proper cable conversion.

Inno Pocket Scan Set Up

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 7

Inno Pocket Scan System Menu

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 8

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 9

ADDR - DMX Address Setting.

1. Press the MENU button until “ADDR” is displayed, and press ENTER.

2. The current address will now be displayed and ashing. Press the UP or DOWN buttons to nd

your desired address. Press ENTER when you have found your desired DMX address, then press

and hold the MENU button for at least 3 seconds to set your desired DMX address.

3. Connect your DMX Controller.

SCND - This will let you set unit as a secondary in a primary/secondary conguration.

1. Press the MENU button until “SCND” is displayed, press ENTER. Either “PRI”, “SEC1”, or

“SEC2” will be displayed.

2. Press the UP or DOWN buttons until your desired setting is displayed, and press ENTER to con-

m.

NOTE: Selecting “SEC2” on a xture will cause that xture to move in contrast to the primary xture.

SHND: SH 0 - SH12 - Show modes 0-12 (Factory programs). Show mode can run with or with-

out sound active mode active.

1. Press the MENU button until “SHND” is displayed, and press ENTER.

2. “Sh X” will now be displayed, “X” representing a number between 0-12. Programs 1-12 are fac-

tory programs, while “Sh 0” is random mode. Press the UP or DOWN buttons to nd your desired

show.

3. When you have found your desired show press ENTER, then press and hold the MENU button

for at least 3 seconds to activate. After you have set your desired show, it can be changed at any

time using the UP or DOWN buttons.

SOUN - Sound Active mode.

1. Press the MENU button until “SOUN” is displayed, and press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to

activate sound active mode, or “OFF” to deactivate sound active mode.

3. Press ENTER, then press and hold the MENU button for at least 3 seconds to activate.

SENS - In this mode you can adjust the sound sensitivity.

1. Press the MENU button until “SENS” is displayed, and press ENTER.

2. A number between 0-100 will be displayed. Press the UP or DOWN buttons to adjust the sound

sensitivity. 0 is the least sensitive, and 100 is the most sensitive.

3. When you have found your desired setting press ENTER to conrm.

DIND - In this mode you can select the dimmer curve.

1. Press the MENU button until “DIND” is displayed, and press ENTER.

2. The current dimmer curve setting will be displayed.

3. Press the UP or DOWN buttons to nd your desired dimmer curve and press ENTER to conrm.

See the Dimmer Curve Chart section of this manual for more information.

Inno Pocket Scan System Menu

ADJ Products, LLC - www.adj.com - Inno Pocket Scan User Manual Page 10

BLND - Blackout or Stand by mode.

1. Press the MENU button until “BLND” is displayed, and press ENTER. Either “Yes” or “No” will be

displayed.

2. To activate Blackout tap the UP or DOWN buttons until “Yes” is displayed, and press ENTER to

conm. The xture will now be in Blackout mode. To deactivate Blackout mode, select “No” and

press ENTER.

LED - With this function you can have the LED display turn o after 10 seconds.

1. Press the MENU button until “LED” is displayed, and press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or DOWN buttons to select “ON” to

keep the LED display on at all times, or “OFF” to switch to have the LED display switch o after

10 seconds of inactivity.

3. Press ENTER to conrm. To make the LED display reappear after it has turned o, press any but-

ton.

DISP - This function will reverse the display 180º.

1. Press the either the MENU button until “DISP” is displayed, and press ENTER.

2. Press the UP button to select “DSIP” to invert the display, or “DISP” to change the display back.

3. Press ENTER to conrm.

PAN - Pan Inversion.

1. Press the MENU button until “PAN” is displayed, and press ENTER. Either “Yes” or “No” will be

displayed.

2. To activate the Pan inversion press the UP or DOWN buttons until “YES” is displayed, and press

ENTER to conm. To deactivate Pan inversion, select “NO” and press ENTER.

TILT - Tilt Inversion.

1. Press the MENU button until “TILT” is displayed, and press ENTER. Either “YES” or “NO” will be

displayed.

2. To activate the Tilt inversion press the UP or DOWN buttons until “YES” is displayed, and press

ENTER to conm. To deactivate Tilt inversion, select “NO” and press ENTER.

TEST - This function will run a self test program. The test program will test pan/tilt movement

and colors.

1. Press the MENU button until “TEST” is displayed, and press ENTER.

2. The xture will now run a self test. Press MENU to exit.

TEMP - With this function you can check the temperature of the xture.

1. Press the MENU button until “TEMP” is displayed, and press ENTER.

2. The temperature of the xture will now be displayed. Press MENU to exit.

FHRS - With this function you can display the running time of the unit.

1. Press the MENU button until “FHRS” is displayed, and press ENTER.

2. The running time of the xture will now be displayed. Press MENU to exit.

Inno Pocket Scan System Menu

Inhaltsverzeichnis

Andere ADJ Beleuchtungsausrüstung Handbücher

ADJ

ADJ 3 SIXTY 2R Bedienungsanleitung

ADJ

ADJ ENCORE BURST UV IP Bedienungsanleitung

ADJ

ADJ MINI DEKKER Bedienungsanleitung

ADJ

ADJ ENCORE BURST 100IP Bedienungsanleitung

ADJ

ADJ SP-1500 Bedienungsanleitung

ADJ

ADJ FOCUS BEAM LED Bedienungsanleitung

ADJ

ADJ FLAT PAR TW5 Bedienungsanleitung

ADJ

ADJ 3D VISION PLUS Bedienungsanleitung

ADJ

ADJ Jelly Jewel Led Bedienungsanleitung

ADJ

ADJ Mega QPlus GO Bedienungsanleitung

ADJ

ADJ H2O LED Bedienungsanleitung

ADJ

ADJ FLASHBACK 4 Bedienungsanleitung

ADJ

ADJ WIFLY PAR QA5 Bedienungsanleitung

ADJ

ADJ Ultra Kling Bar 18 Bedienungsanleitung

ADJ

ADJ Encore Profile Mini WW Bedienungsanleitung

ADJ

ADJ FLAT PAR TW12 Bedienungsanleitung

ADJ

ADJ StarTec Series Bedienungsanleitung

ADJ

ADJ INNO POCKET ROLL Bedienungsanleitung

ADJ

ADJ JOLT PANEL FX Bedienungsanleitung

ADJ

ADJ COB CANNON LP200 Bedienungsanleitung

ADJ

ADJ 5P HEX/5P HEX PEARL Bedienungsanleitung

ADJ

ADJ Vizi Spot 5R Bedienungsanleitung

ADJ

ADJ Diversa Ray Bedienungsanleitung

ADJ

ADJ American DJ H2O LED Handbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung