ADTRAN NetVanta 3458-PoE Bedienungsanleitung

Quick Start Guide, 61200824G1-13A, March 2009 1

NETVANTA 3458 ROUTER

P/N 1200824G1

GETTING STARTED

Two configuration methods are available for your NetVanta router:

• Web-based graphical user interface (GUI)

• AOS command line interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations

for each setting. However, using the AOS CLI may be necessary for more advanced

configurations.

ACCESS THE GUI

You may access the GUI from any Web browser on your network by following these steps:

1. Connect the router to your PC using the ETH 0/1 port on the back of the unit.

2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address,

you will need to change the unit’s IP address using the CLI. (Refer to the next two sections

for instructions.)

3. Enter the unit’s IP address in your browser address line. The default IP address is

10.10.10.1.

4. You will then be prompted for the user name and password (the default settings are admin

and password).

5. The initial GUI screen appears.

ACCESS THE CLI

Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the

NetVanta router CONSOLE port, you need the following items:

• VT100 terminal or PC (with VT100 terminal emulation software)

• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate

interface for your terminal or PC communication port on the other end

1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the front

panel of the unit.

2. Connect the other end of the serial cable to the terminal or PC.

3. Provide power to the unit as appropriate. Refer to the NetVanta 3000 Series Hardware

Installation Guide (provided on the AOS Documentation CD) for more details.

4. Once the unit is powered up, open a VT100 terminal session using the following settings:

9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the

AOS CLI.

5. Enter enable at the >prompt.

6. Enter the enable password when prompted. The default password is password.

CONFIGURE YOUR APPLICATION

More detailed documentation for configuring your ADTRAN unit is provided on the AOS

Documentation CD included in your shipment. For more detail on hardware setup, refer to the

appropriate NIM quick start guides and the hardware installation guide. For more detail on

configuring your system, refer to the AOS Command Reference Guide, configuration guides, and

technical support notes.

Important: For additional details on product features, specifications,

installation, and safety, refer to the appropriate hardware installation

guide on the AOS Documentation CD shipped with the base unit and

available online at www.adtran.com.

CONFIGURE THE UNIT’SIP ADDRESS

The following steps create an IP address and subnet mask for ETH 0/1. If you are not sure what

IP address to assign, please contact your network administrator.

1. At the # prompt, enter config terminal.

2. At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for

the Ethernet port located on the rear of the unit.

3. Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the Ethernet port

using a 24-bit subnet mask.

4. Enter ip route 0.0.0.0 0.0.0.0 192.22.72.2 to add a default route to the route table. If

necessary, contact your network administrator to obtain the IP address (and subnet mask)

for your particular configuration.

5. Enter no shutdown to activate the interface to pass data.

6. Enter exit to exit the Ethernet interface commands and return to the Global Configuration

mode.

ENABLE TELNET ACCESS

The following steps create a password of adtran for Telnet access. By default, Telnet access is

enabled with a password of password.

1. Verify that the prompt of your unit displays (config)#.

2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.

3. Enter login to initiate Telnet access.

4. Enter password adtran to change the login password for the Telnet sessions.

5. Enter exit to return to the Global Configuration mode.

6. Verify that the prompt of your unit displays (config)#.

7. Enter do write memory to save the current configuration.

The configuration parameters used in the examples outlined in this

document are for instructional purposes only. Please replace all

underlined entries (example) with your specific parameters to configure

your application.

Depending on your configuration, you may need to set a default gateway

as well using the (config)#ip default gateway command. If IP routing is

enabled on the unit, do NOT set a default gateway.

CONSOLE PINOUTS

Pin Name Description

1 DCD Data Carrier Detect (output)

2 RD Receive Data (output)

3 TD Transmit Data (input)

4 DTR Data Terminal Ready (input)

5 SG Signal Ground

6 — Tied to Pin 1 (output)

7 — Unused

8 — Tied to Pin 1 (output)

9 — Unused

ETHERNET PINOUTS

Pin Name Description

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4, 5 — Unused

6 RX2 Receive Negative

7, 8 — Unused

SWITCH PORT (1 THROUGH 8) PINOUTS

Pin Name Description

1 TX1 Transmit Positive (PoE negative rail)

2 TX2 Transmit Negative (PoE negative rail)

3 RX1 Receive Positive (PoE positive rail)

4, 5 — Unused

6 RX2 Receive Negative (PoE positive rail)

7, 8 — Unused

CONFIGURE THE UNIT’SIP ADDRESS

The following steps create an IP address and subnet mask for ETH 0/1. If you are not sure what

IP address to assign, please contact your network administrator.

1. At the # prompt, enter config terminal.

2. At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for

the Ethernet port located on the rear of the unit.

3. Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the Ethernet port

using a 24-bit subnet mask.

4. Enter ip route 0.0.0.0 0.0.0.0 192.22.72.2 to add a default route to the route table. If

necessary, contact your network administrator to obtain the IP address (and subnet mask)

for your particular configuration.

5. Enter no shutdown to activate the interface to pass data.

6. Enter exit to exit the Ethernet interface commands and return to the Global Configuration

mode.

ENABLE TELNET ACCESS

The following steps create a password of adtran for Telnet access. By default, Telnet access is

enabled with a password of password.

1. Verify that the prompt of your unit displays (config)#.

2. Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.

3. Enter login to initiate Telnet access.

4. Enter password adtran to change the login password for the Telnet sessions.

5. Enter exit to return to the Global Configuration mode.

6. Verify that the prompt of your unit displays (config)#.

7. Enter do write memory to save the current configuration.

The configuration parameters used in the examples outlined in this

document are for instructional purposes only. Please replace all

underlined entries (example) with your specific parameters to configure

your application.

Depending on your configuration, you may need to set a default gateway

as well using the (config)#ip default gateway command. If IP routing is

enabled on the unit, do NOT set a default gateway.

CONSOLE PINOUTS

Pin Name Description

1 DCD Data Carrier Detect (output)

2 RD Receive Data (output)

3 TD Transmit Data (input)

4 DTR Data Terminal Ready (input)

5 SG Signal Ground

6 — Tied to Pin 1 (output)

7 — Unused

8 — Tied to Pin 1 (output)

9 — Unused

ETHERNET PINOUTS

Pin Name Description

1 TX1 Transmit Positive

2 TX2 Transmit Negative

3 RX1 Receive Positive

4, 5 — Unused

6 RX2 Receive Negative

7, 8 — Unused

SWITCH PORT (1 THROUGH 8) PINOUTS

Pin Name Description

1 TX1 Transmit Positive (PoE negative rail)

2 TX2 Transmit Negative (PoE negative rail)

3 RX1 Receive Positive (PoE positive rail)

4, 5 — Unused

6 RX2 Receive Negative (PoE positive rail)

7, 8 — Unused

Quick Start Guide, 61200824G1-13A, March 2009 1

NETVANTA 3458 ROUTER

P/N 1200824G1

GETTING STARTED

Two configuration methods are available for your NetVanta router:

• Web-based graphical user interface (GUI)

• AOS command line interface (CLI)

The GUI lets you configure the main unit settings and provides online guidance and explanations

for each setting. However, using the AOS CLI may be necessary for more advanced

configurations.

ACCESS THE GUI

You may access the GUI from any Web browser on your network by following these steps:

1. Connect the router to your PC using the ETH 0/1 port on the back of the unit.

2. Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address,

you will need to change the unit’s IP address using the CLI. (Refer to the next two sections

for instructions.)

3. Enter the unit’s IP address in your browser address line. The default IP address is

10.10.10.1.

4. You will then be prompted for the user name and password (the default settings are admin

and password).

5. The initial GUI screen appears.

ACCESS THE CLI

Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the

NetVanta router CONSOLE port, you need the following items:

• VT100 terminal or PC (with VT100 terminal emulation software)

• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate

interface for your terminal or PC communication port on the other end

1. Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the front

panel of the unit.

2. Connect the other end of the serial cable to the terminal or PC.

3. Provide power to the unit as appropriate. Refer to the NetVanta 3000 Series Hardware

Installation Guide (provided on the AOS Documentation CD) for more details.

4. Once the unit is powered up, open a VT100 terminal session using the following settings:

9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the

AOS CLI.

5. Enter enable at the >prompt.

6. Enter the enable password when prompted. The default password is password.

CONFIGURE YOUR APPLICATION

More detailed documentation for configuring your ADTRAN unit is provided on the AOS

Documentation CD included in your shipment. For more detail on hardware setup, refer to the

appropriate NIM quick start guides and the hardware installation guide. For more detail on

configuring your system, refer to the AOS Command Reference Guide, configuration guides, and

technical support notes.

Important: For additional details on product features, specifications,

installation, and safety, refer to the appropriate hardware installation

guide on the AOS Documentation CD shipped with the base unit and

available online at www.adtran.com.

Andere Handbücher für NetVanta 3458-PoE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Router Handbücher

ADTRAN

ADTRAN Total Access 1250 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1335 Series Bedienungsanleitung

ADTRAN

ADTRAN Total Access 904 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 5305 Handbuch

ADTRAN

ADTRAN NetVanta 3130 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 340 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3200 series Benutzerhandbuch

ADTRAN

ADTRAN NetVanta 3200 series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 4300 Series Handbuch

ADTRAN

ADTRAN NetVanta 2000 Series Bedienungsanleitung

ADTRAN

ADTRAN Total Access 1200F Bedienungsanleitung

ADTRAN

ADTRAN Express XL 1200070L1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1335 Series Bedienungsanleitung

ADTRAN

ADTRAN TRACER 5045 Bedienungsanleitung

ADTRAN

ADTRAN 1202870L1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 5305 Handbuch

ADTRAN

ADTRAN 1203860G1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN 1200350L1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3120 with DBU Handbuch

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN ISU 128 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1335 Series Bedienungsanleitung

ADTRAN

ADTRAN TSU NetVanta Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise