ADTRAN SR700ac Bedienungsanleitung

SR700ac

Quick Start Guide

Installation

1. Connect one end of the phone cable to the DSL port on the gateway and connect the other end to the phone jack

on the wall installed by your provider.

2. Connect one end of the Ethernet cable to a LAN port on the gateway and connect the other end to your computer.

3. Plug the power adapter to the wall outlet and then connect the other end of it to the Power port of the gateway.

Turn on the unit by pressing the On/Off button on the back of the gateway.

4. If you plan to create an LTE connection, insert a SIM card into the SIM slot located under the WAN port.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to

complete before you can begin using your Internet applications (browser, email, etc.). If you are unable to connect to the

Internet, verify that all cable connections are in place and the gateway’s power is turned on.

POWERWANDSL 1 2 3 4

Reset

SIM

123

LED Indicators

The LEDs on the SR700ac gateway can help you better understand

the current state of your gateway.

Legend: Green Green blinking Red Red blinking

LED Action Explanation

All LEDs except those

listed below

Connection enabled.

Data being transferred.

DSL & WAN Not lit Connection dropped; attempting resynchronization.

POWER Device has power and is ready to use.

Power up test failure.

Note: This LED flashes red briefly on startup; this is normal.

INET Gateway online.

Data being transferred.

Connection dropped; attempting resynchronization.

Not lit IP connection failed.

LED Action Explanation

WPS WPS setup procedure in progress.

WPS connection completed.

No partner found for pairing.

Session overlap detected. Possible security risk.

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small

circular hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into the

hole, press the Reset button gently for 1 second, and then release the button. The system reboots and returns to the

factory defaults.

Logging in to your gateway

To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed the

steps in "Installation" before you begin.

1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.

2. Enter the factory default credentials shown below and click OK.

User Name: admin Password: admin

Note: Your service provider may use other settings. Contact your provider for details.

3. At the bottom of the page, click Manage gateway (advanced). The gateway interface appears.

Configuring the WAN manually

If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer2 Interface and WAN Service

sections of the SmartRG SR700ac Gateway User Manual to manually establish a connection.

Configuring an LTE Connection

1. With the gold contacts facing up, insert the SIM card containing the LTE information into the SIMslot on the back of

the gateway.

Note: The SR700ac gateway accepts a Standard SIM (15 x 25mm) card.

2. In the left navigation bar, click LTE WAN Service >Network Settings.

3. In the Network Dial Mode field, select the dial mode for this connection.

4. In the APN Name field, enter the APN for your network provider.

5. Click Save/Apply to apply your changes.

Note: It may take up to 90 seconds for the Save action to complete.

Your device should now be connected to your network via LTE.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow the

instructions for the applicable method.

1. In the left navigation bar, click Wireless.

2. If the Enable Wireless option is not already selected, select it now.

3. Continue with your preferred method of wireless setup.

WPS Method

If the device you wish to connect to the Internet via your gateway supports the WPS secure WiFi connection method, follow

these steps.

1. In the left navigation bar, click Wireless.

2. Click the wireless band that you want to configure and then click Security.

3. In the Enable WPS field, select Enabled.

Andere Handbücher für SR700ac

Inhaltsverzeichnis

Andere ADTRAN Netzwerk-Router Handbücher

ADTRAN

ADTRAN NetVanta 1535P Handbuch

ADTRAN

ADTRAN NetVanta 3200 series Handbuch

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3458-PoE Handbuch

ADTRAN

ADTRAN 1203860G1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3120 with DBU Handbuch

ADTRAN

ADTRAN 617600028F1 Bedienungsanleitung

ADTRAN

ADTRAN 1200263L1-1.2A Bedienungsanleitung

ADTRAN

ADTRAN Express L1.5 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 5305 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3305 Bedienungsanleitung

ADTRAN

ADTRAN 4200990G1 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1335 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3100 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 340 Bedienungsanleitung

ADTRAN

ADTRAN BLUESOCKET VWLAN Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3448 Bedienungsanleitung

ADTRAN

ADTRAN 1200821F1 Handbuch

ADTRAN

ADTRAN NetVanta 1355 PWR Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 3430 Bedienungsanleitung

ADTRAN

ADTRAN MX410 Benutzerhandbuch

ADTRAN

ADTRAN Total Access 5000 Kurzanleitung

ADTRAN

ADTRAN netvanta 1230 series Handbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise