ADTRAN NT1 ACE4 Bedienungsanleitung

NT1 ACE4

User Manual

1200242L1: NT1 ACE4

336012VUR01: Power Supply 12 VDC/800 mA

61200242L1-1A

September 2000

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

(256) 963-8000

Printed in U.S.A.

61200242L1-1 NT1 ACE4User Manual iii

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety pre-

cautions should always be followed to reduce the risk of

fire, electric shock and injury to persons. The precautions

are listed below.

1. Donotusethisproductnearwater(forexam-

ple,nearabathtub,washbowl,kitchensinkor

laundry tub, in a wet basement or near a swim-

ming pool).

2. Never install telephone jacks in wet locations un-

lessthejackisspecificallydesignedforwetloca-

tions.

3. Avoid using a telephone (other than a cordless

type) during an electrical storm. There may be a

remote risk of electric shock from lightning.

4. Donotusethetelephonetoreportagasleakinthe

vicinity of the leak.

5. Use only the power cord, power supply, and/or

batteries indicated in the manual. Do not dispose

of batteries in a fire. They may explode. Check lo-

cal codes for any special disposal instructions.

6. Never touch uninsulated telephone wires or ter-

minals unless the telephone line has been discon-

nected at the network interface.

7. Use caution when installing or modifying tele-

phone lines.

SAVE THESE INSTRUCTIONS.

iv NT1 ACE4User Manual 61200242L1-1

AFFIDAVIT REQUIREMENTS FOR CONNECTION TO

DIGITAL SERVICES

• An affidavit is required to be given to the telephone

company whenever digital terminal equipment with-

out encoded analog content and billing protection is

used to transmit digital signals containing encoded

analog content which are intended for eventual con-

version into voiceband analog signals and transmitted

on the network.

• The affidavit shall affirm that either no encoded ana-

log content or billing information is being transmitted

or that the output of the device meets Part 68 encoded

analog content or billing protection specifications.

• End user/customer will be responsible to file an affi-

davit with the local exchange carrier when connecting

unprotected CPE to a 1.544 Mbps or subrate digital

services.

• Until such time as subrate digital terminal equipment

is registered for voice applications, the affidavit re-

quirement for subrate services is waived.

61200242L1-1 NT1 ACE4User Manual v

AFFIDAVIT FOR CONNECTION OF CUSTOMER

PREMISES EQUIPMENT TO 1.544 MBPS AND/OR

SUBRATE DIGITAL SERVICES

For the work to be performed in the certified territory of

_______________

(telco name)

State of ___________________

County of _________________

I, ______________________________(name),

________________________________(business address),

______________________ (telephone number) being duly

sworn, state:

Ihaveresponsibilityfortheoperationandmaintenanceof

the terminal equipment to be connected to 1.544 Mbps

and/or ________ subrate digital services. The terminal

equipment to be connected complies with Part 68 of the

FCC rules except for the encoded analog content and bill-

ing protection specifications. With respect to encoded an-

alog content and billing protection:

( ) I attest that all operations associated with the estab-

lishment,maintenance,andadjustmentof thedigitalCPE

with respect to analog content and encoded billing pro-

tection information continuously complies with Part 68 of

the FCC Rules and Regulations.

( ) The digital CPE does not transmit digital signals containing

encodedanalogcontentorbillinginformationwhichisintended

to be decoded within the telecommunications network.

vi NT1 ACE4User Manual 61200242L1-1

( ) The encoded analog content and billing protection is

factory set and is not under the control of the customer.

I attest that the operator(s)/maintainer(s) of the digital

CPE responsible for the establishment, maintenance, and

adjustment of the encoded analog content and billing in-

formation has (have) been trained to perform these func-

tionsbysuccessfullyhavingcompletedoneofthe

following (check appropriate blocks):

( ) A. A training course provided by the manufacturer/

grantee of the equipment used to encode analog signals;

( ) B. A training course provided by the customer or au-

thorized representative, using training materials and in-

structions provided by the manufacturer/grantee of the

equipment used to encode analog signals; or

( ) C. An independent training course (e.g., trade school

or technical institution) recognized by the manufacturer/

grantee of the equipment used to encode analog signals;

( ) D. In lieu of the preceding training requirements, the

operator(s)/maintainer(s) is (are) under the control of a

supervisor trained in accordance with _________ (circle

one) above.

I agree to provide _________________ (telco's name) with

proper documentation to demonstrate compliance with

the information as provided in the preceding paragraph,

if so requested.

61200242L1-1 NT1 ACE4User Manual vii

_________________________________Signature

_________________________________Title

_________________________________ Date

Transcribed and sworn to before me

This ________ day of ________, 199___

_________________________________

Notary Public

My commission expires:

_________________________________

viii NT1 ACE4User Manual 61200242L1-1

FCC INFORMATION

This device complies with Part 15 of the FCC rules. Oper-

ation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this

device must accept any interference received, including

interference that may cause undesired operation.

Changes or modifications to this unit not ex-

pressly approved by the party responsible for

compliance could void the user's authority to op-

erate the equipment.

Canadian Standards Association

This device must be powered by a CSA approved power

supply or a power supply meeting the requirements of

CS03, Part I Section 1.4.2.

FCC regulations require that the following

informationbeprovidedinthismanual:

1. This equipment complies with Part 68 of the FCC

rules. On the bottom of the equipment housing is a la-

bel that shows the FCC registration number for this

equipment. If requested, provide this information to

the telephone company.

61200242L1-1 NT1 ACE4User Manual ix

2. If this equipment causes harm to the telephone network,

the telephone company may temporarily discontinue

service. If possible, advance notification is given; oth-

erwise, notification is given as soon as possible. The

telephone companywilladvisethecustomeroftheright

to file a complaint with the FCC.

3. The telephone company may make changes in its facili-

ties, equipment, operations, or procedures that could af-

fect the proper operation of this equipment; advance

notification and the opportunity to maintain uninter-

rupted service is given.

4. If experiencing difficulty with this equipment, please con-

tact ADTRAN for repair and warranty information. The

telephone company may requirethisequipment to be dis-

connected from the network until the problem is correct-

ed, or it is certain the equipment is not malfunctioning.

5. This unit contains no user-serviceable parts.

6. An FCC compliant telephone cord with a modular plug

is provided with this equipment. In addition, an FCC

compliant cable appropriate for the dial backup option

orderedisprovidedwiththisequipment. Thisequip-

ment is designed to be connected to the telephone net-

work or premises wiring using an FCC compatible

modular jack, which is Part 68 compliant.

xNT1ACE

4User Manual 61200242L1-1

7. The following information may be required when ap-

plying to the local telephone company for leased line

facilities.

8. The FCC recommends that the AC outlet, to which

equipment requiring AC power is to be installed, is pro-

videdwithanACsurgearrester.

Service

Type Digital Facility

Interface Code Service

Order Code Network

Jacks

ISDN 02IS5 6.0N RJ-49C

Inhaltsverzeichnis

Andere ADTRAN Stromversorgung Handbücher

ADTRAN

ADTRAN Power Supply/Battery Charger Bedienungsanleitung

ADTRAN

ADTRAN Total Access 850 Bedienungsanleitung

ADTRAN

ADTRAN 4303 DC Handbuch

ADTRAN

ADTRAN NetVanta 1760-12F Bedienungsanleitung

ADTRAN

ADTRAN Total Access 1500 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1000 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1131 RPS/EPS Bedienungsanleitung

ADTRAN

ADTRAN TOTAL ACCESS MX2800 Bedienungsanleitung

ADTRAN

ADTRAN 3192 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1131 RPS/EPS Bedienungsanleitung

ADTRAN

ADTRAN ATLAS 890 Bedienungsanleitung

ADTRAN

ADTRAN NT1 T400 Bedienungsanleitung

ADTRAN

ADTRAN 61175044L2-22B Bedienungsanleitung

ADTRAN

ADTRAN Total Access 850 Bedienungsanleitung

ADTRAN

ADTRAN D4PBCU0 Wartungs- und Serviceanleitung

ADTRAN

ADTRAN HDSL 851 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1110 Bedienungsanleitung

ADTRAN

ADTRAN TOTAL ACCESS 4303 PLUS Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung