ADTRAN NT1 T400 Bedienungsanleitung

NT1 Type 400

NT1 Type 400 Standalone 1212016L1

NT1 Type 400 Circuit Pack 1212010

USER MANUAL

61212016L1-1B

January 1999

This device complies with Part 15 of the FCC rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful in-

terference, and (2) this device must accept any interference received, in-

cluding interference that may cause undesired operation.

Changes or modifications to this unit not expressly approved by the par-

ty responsible for compliance could void the user's authority to operate

the equipment.

Canadian Standards Association

This device must be powered by a CSA approved power supply or a pow-

er supply meeting the requirements of CS03, Part I Section 1.4.2.

Warranties

ADTRAN will repair or replace this product within five years from the

date of shipment if it does not meet its published specifications or fails

while in service. For detailed warranty, repair, and return information, re-

fer to the ADTRAN Equipment Warranty and Repair and Return Policy

Procedure. Return Material Authorization (RMA) is required prior to re-

turning equipment to ADTRAN. (See inside back cover for phone number

and address to use.)

901 Explorer Boulevard

P.O. Box 140000

Huntsville, AL 35814-4000

Phone: (256) 963-8000

Printed in USA.

FCCregulationsrequirethatthe followinginformationbe provided in this

manual:

1. This equipment complies with Part 68 of the FCC rules. On the

bottom of the equipment housing is a label that shows the FCC

registration number and Ringer Equivalence Number (REN)

for this equipment. If requested, provide this information to

the telephone company.

2. If this equipment causes harm to the telephone network, the tele-

phonecompanymaytemporarilydiscontinueservice. Ifpossible,

advance notification is given; otherwise, notification is given as

soon as possible. The telephone company will advise the custom-

er of the right to file a complaint with the FCC.

3. The telephone company may make changes in its facilities, equip-

ment, operations, or procedures that could affect the proper oper-

ation ofthis equipment; advance notification and theopportunity

to maintain uninterrupted service is given.

4. If experiencing difficulty with this equipment, please contact

ADTRAN for repair and warranty information. The telephone

companymayrequirethisequipmenttobedisconnectedfromthe

network until the problem is corrected, or it is certain the equip-

ment is not malfunctioning.

5. This unit contains no user serviceable parts.

6. An FCC compliant telephone cord with a modular plug is provid-

ed with this equipment. In addition, an FCC compliant cable ap-

propriatefor the dial backup optionordered isprovided with this

equipment. This equipment is designed to be connected to the

telephone network or premises wiring using an FCC compatible

modular jack, which is Part 68 compliant.

7. The following information may be required when applyingto the

local telephone company for leased line facilities.

Service

Type Digital Facility

Interface Code Service

Order Code Network

Jacks

ISDN 02IS5 6.0F RJ-49C

ADTRAN YEAR 2000 (Y2K)

READINESS DISCLOSURE

ADTRAN has established a Year 2000 program to ensure that our prod-

ucts and operations will correctly function in the new millennium. ADT-

RAN warrants that all products meet Year 2000 specifications regardless

or model or revision. Information about ADTRAN’s Year 2000 compli-

ance program is available at the following:

Web Site www.adtran.com

Product Matrix www.adtran.com/Y2Kfax.html

Faxback Document Line (256) 963-8200

Y2K plans and product certifications

are listed in the matrix

Y2K Project Line (256) 963-2200

E-mail year 2000@adtran.com

CUSTOMER INSTRUCTIONS

1. The mounting of the registered unit in the final assembly must

be made so that the registered unit is isolated from exposure to

any hazardous voltages within the assembly. Adequate separa-

tion and restraint of cables and cords must be provided.

2. Thecircuitryfromtheregisteredunittothetelephonelinemustbe

provided in wiring that carries no other circuitry unless specifical-

ly allowed by therules (such as PC and PRleads). PC board traces

carrying tip and ring leads shall have sufficient spacing to avoid

surge breakdown.

3. A modular plug or jack shall be provided which complies with

Part 68, Subpart F requirements for dimensions, tolerances metal-

lic plating.

CANADIAN EMISSIONS REQUIREMENTS

This digital apparatus does not exceed the Class B limits for radio noise emis-

sions from digital apparatus as set out in the interference-causing equipment stan-

dard entitled "Digital Apparatus," ICES-003 of the Department of

Communications.

Cet appareil numerique respecte les limites de bruits radioelectriques applicables

aux appareils numeriques de Class B prescrites dans la norme sur le materiel

brouilleur: "Appareils Numeriques," NMB-003 edictee par le ministre des Com-

munications.

CANADIAN EQUIPMENT LIMITATIONS

Notice: The Canadian Industry and Science Canada label identifies certified equip-

ment. This certification means that the equipment meets certain telecommunications

network protective, operational, and safety requirements. The Department does not

guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, ensure that it is permissible to be connected to

the facilities of the local telecommunications company. The equipment must also

be installed using an acceptable method of connection. In some cases, the com-

pany’s inside wiring associated with a single-line individual service may be

extended by means of a certified connector assembly (telephone extension cord).

Compliance with the above conditions may not prevent degradation of service in

some situations.

Repairs to certified equipment should be made by an authorized Canadian main-

tenance facility designated by the supplier. Any repairs or alterations made by

the user to this equipment, or equipment malfunctions, may give the telecommu-

nications company cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connec-

tions of the power utility, telephone lines, and internal metallic water pipe sys-

tem, if present, are connected together. This precaution may be particularly

important in rural areas.

Users should not attempt to make such connections them-

selves, but should contact the appropriate electric inspection

authority, or an electrician, as appropriate.

The Load Number (LN) assigned to each terminal device denotes the percentage

of the total load to be connected to a telephone loop which is used by the device,

to prevent overloading. The termination on a loop may consist of any combina-

tion of devices subject only to the requirement that the total of the Load Numbers

of all devices does not exceed 100.

61212016L1-1 NT1 T400 User Manual ix

Table of Contents

1.0 GENERAL...............................................................................1

1.01 Unit Overview .........................................................................1

1.02 Basic Rate Description ...........................................................2

1.03 Passive Bus Description.........................................................2

1.04 Powering TEs from the NT1 ...................................................2

1.05 Rear Panel..............................................................................2

2.0 INSTALLATION ......................................................................3

2.01 Setting the Option Switches....................................................3

2.02 Powering Up the NT1 Type 400 Standalone ..........................4

2.03 Connecting the Terminal Equipment ......................................4

3.0 TROUBLESHOOTING............................................................5

4.0 MAINTENANCE......................................................................6

5.0 REMOTE TESTING................................................................6

6.0 REPAIR AND RETURN..........................................................6

7.0 SPECIFICATIONS..................................................................7

APPENDIX A

NT1 TYPE 400 CIRCUIT PACK RACK INSTALLATION .................9

APPENDIX B

S/T BUS CONFIGURATIONS........................................................11

Table of Contents

x NT1 T400 User Manual 61212016L1-1

FIGURES

Figure 1. NT1 Type 400 Standalone Rear Panel ............................2

Figure 2. NT1 Type 400 Switch Option Locations...........................3

Figure A-1.NT1 T400 Circuit Pack Connector Pin Assignments....10

Figure B-1.Short Passive Bus Configuration..................................11

Figure B-2.Extended Passive Bus Configuration ...........................11

TABLES

Table 1. NT1 Type 400 Front Panel Indicators...............................1

Table 2. NT1 Type 400 Switch settings.........................................3

Table 3. NT1 Pin Assignments.......................................................4

61212016L1-1 NT1 T400 User Manual 1

1.0 GENERAL

1.01 Unit Overview

The ADTRAN NT1 Type 400 provides a basic rate interface be-

tween the customer’s ISDN Terminal Equipment (TE) and the

ISDN Network. Two interfaces areprovided for this purpose: con-

nection to the ISDN network is made by the “U” interface and

connection to the customer's ISDN TE is made by the S/T inter-

face.

The NT1 Type 400 is available in two configurations:

• The NT1 Type 400 Standalone with an internal power supply,

Part No. 1212.016L1.

• The NT1 Type 400 Circuit Pack, Part No. 1212.010.

The ADTRAN NT1 Type 400 Standalone consists of two parts, a

metal housing containing the power supply, connectors, and the

NT1 Type 400 Circuit Pack. The Circuit Pack can be removed from

the housing by removing the plastic front panel and sliding the

unit out of the housing. This allows access to the option switches

which may be reset by the customer. The NT1 Type 400 Circuit

Pack can also be purchased as a separate unit and mounted in a

Type 400 NCTE rack, as indicated in APPENDIX A.

LED Indicators

Table 1 describes the status of the LEDs located on the front panel

of the NT1 Type 400. There is a READY and ERROR indicator for

each port of the NT1 Type 400.

Table 1: NT1 Type 400 Front Panel Indicators

If an ERROR indicator is illuminated, check the flash rate of the

READY indicator to determine the source of the error. A faster 8

Hz flash rate (8 flashes per second) indicates a network problem.

A slower 1 Hz rate (1 flash per second) indicates an S/T interface

problem.

LED Color Description

READY Green S/T and U interfaces ready

to place call

ERROR Red S/T or U interface not ready

POWER Green Unit has power

Inhaltsverzeichnis

Andere ADTRAN Stromversorgung Handbücher

ADTRAN

ADTRAN Total Access 850 Bedienungsanleitung

ADTRAN

ADTRAN Power Supply/Battery Charger Bedienungsanleitung

ADTRAN

ADTRAN D4PBCU0 Wartungs- und Serviceanleitung

ADTRAN

ADTRAN NetVanta 1000 Series Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1131 RPS/EPS Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1110 Bedienungsanleitung

ADTRAN

ADTRAN 4303 DC Handbuch

ADTRAN

ADTRAN NetVanta 1131 RPS/EPS Bedienungsanleitung

ADTRAN

ADTRAN 3192 Bedienungsanleitung

ADTRAN

ADTRAN TOTAL ACCESS MX2800 Bedienungsanleitung

ADTRAN

ADTRAN TOTAL ACCESS 4303 PLUS Bedienungsanleitung

ADTRAN

ADTRAN NT1 ACE4 Bedienungsanleitung

ADTRAN

ADTRAN Total Access 850 Bedienungsanleitung

ADTRAN

ADTRAN HDSL 851 Bedienungsanleitung

ADTRAN

ADTRAN ATLAS 890 Bedienungsanleitung

ADTRAN

ADTRAN NetVanta 1760-12F Bedienungsanleitung

ADTRAN

ADTRAN Total Access 1500 Bedienungsanleitung

ADTRAN

ADTRAN 61175044L2-22B Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung