Advanced Radio Smart Switch Bedienungsanleitung

Smart Switch

Quick Start Guide

Thank you for your purchase of the Advance Radio Smart Switch.

In this quick start guide we will show you how to connect your new Smart

Switch, General use and Set Up. Please take the me to understand this guide

before installaon

IMPORTANT

The touch screen display supplied with the Smart Switch should be protected

from vibraon.

Before installaon please ensure that your baeries are fully charged. The

smart switch relies on this to know how much you have used in each pack.

WARNING

The Smart Screen shows you how much you have used out of each pack and

displays this as an indicator on the Smart Screen. NEVER FLY WITH BATTERY

PACKS THAT HAVE 35% OR LESS CAPACITY (RED ZONE ON THE BATTERY INDICA-

TOR). Doing so might put your model at risk.

Specicaons:

* Ultra low foot print for the best scale looks.

* With built in Baery Guard Technology. The Smart Switch constantly monitors baery volt-

age and current draw.

*Works with single or dual baery conguraon.

* Works with all baery chemistries. LiFe. LiPo, Lion, NiMh, NiCD. Baery voltage range can

be from 4.8volts to 12 volts.

* Minimal external Footprint - All you see on the outside of your model is a 3mm pin Flag

socket and (if required) a ultra high bright Blue LED. The pin Flag controls the internal power

switch and dual baery redundancy.

* Full Dual Baery Redundancy - If one baery fails the other baery takes full control.

* Maximum Baery Power Balancing – Using dual baery technology, The Smart

Switch draws current proporonally from both baeries while moving both baeries to a

complete load balance situaon. This means you get the maximum capacity out of both

baeries all the me.

* 2 x 25 amp independent circuits. Smart Switch is 2 x 25amp circuits into a high power

matching baery redundancy circuit. Smart Switch actually uses 4 x 50 amp rated FET circuits

for baery power matching. We passively rate the Smart Switch at 25amps per circuit.

* Available as standard with JR In/Out, Futaba In/Out, Ultra In/Out, EC3 In/Out or XT60 In/

Out combinaons. In/Out power connecons can be tailored to suit your connecon require-

ments. Please specify when ordering.

* For higher current rang please select 18AWG or 16AWG connecon cables. If you are not

sure just drop us an email to sa[email protected]

Included Items:

1 x Live feedback touch screen Smart display

1 x Pin Flag Switch with mounng hardware.

1 x Ultra Bright Blue LED with mounng hardware.

1 x Dual Baery Balancing power switch circuit with built in baery watch technology

2 x Sets of Input and Output connectors of your choice.

3 x piece of 3M lock tape for mounng

Installaon and Mounng Instrucons

In this secon we will explain how to mount both the Smart Switch and the Smart Display.

Mounng the Smart Switch

Included with the Smart Switch are 3 pieces of 3M Clear Velcro tape (seen below). One

of these pieces should be used to mount the switch.

Before applying the 3M tape, we recommend clean-

ing both surfaces you wish to use the 3M tape on

with isopropyl alcohol or methylated spirits. Wait a

moment for this to dry

Once both surfaces are clean, start by peeling the

protecve lm o one side of the tape and placing

this side on the switch. Once you are happy with

this, peel the protecve lm o the other side of

the 3M tape and place where desired.

With the palm of your hand, rmly press down on the switch to ensure both the 3M

tape is secure and the Velcro is aached.

Mounng the Smart Display

There are 2 opons of mounng the Smart display.

NOTE: Which ever method of mounng you choose, ensure the purple cable that comes

out of the Smart Display is not crushed in anyway. Doing so will reduce the longevity of

the cables.

Opon 2. For hard mounng, the screen case has 2 lile tabs with eyelet holes in them. If you are

mounng the screen in a scale cockpit, or in a non vibraon model. (e.g Turbine) these holes can be

used to ax the Smart Display.

Simply place the Smart Display where you wish to mount it. Holding it in place, make a dot using a

pen or pencil in each eyelet hole. Removing the screen, drill a hole where you placed the dots.

Now simply screw the Smart Display in place.

NOTE: Hard mounng the Smart Display provides lile to no protecon against vibraon.

Use this method if you are using a non vibraon model or only where there is lile to no

vibraon. AVOID MOUNTING IN HIGH VIBRATION AREAS. VIBRATION DAMAGE IS NOT

COVERED UNDER WARRANTY.

Opon 1. Using the remaining pieces of 3M clear tape, we can mount the back of the screen

to a surface. NOTE: This is a semi hard mount, and will provide a good resistance to vibra-

on. AVOID MOUNTING IN HIGH VIBRATION AREAS. VIBRATION DAMAGE IS NOT COV-

ERED UNDER WARRANTY. As menoned above, clean both the back of the smart screen and

surface that it is being mounted. Place a piece of 3M tape each side of the purple cable.

Trimming the tape as necessary. Remove the clear lm and place the tape on the back of the

screen then press the screen into place. IMPORTANT: DO NOT APPLY FORCE DIRECTLY ON TO

THE SCREEN WITH FORCE AS IT MAY BREAK. Press on the black case around the screen to

ensure it is secure

Self Balancing Receiver

Battery 1

Self Balancing Receiver

Battery 2

Smart Switch with

2 inputs and 2 outputs

Failsafe Pin

Barrel Switch

Receiver Battery Input

Or Regulator

Additional Receiver

Battery Input

(If available)

leave disconnected

Red Input Cable

Yellow Input Cable

Gray Cable

Single Receiver

Red OutPut Cable

Yellow OutPut Cable

Self Balancing Receiver

Battery 1

Self Balancing Receiver

Battery 2

Smart Switch with

2 inputs and 2 outputs

Receiver 1

Battery Input

Red Input Cable

BLUE LED

Blue Cable

Red OutPut Cable

Dual Receiver

Receiver 2

Battery Input

Smart Switch

Connection Guide

Input Connectors Output Connectors

Ultra Female

JR Type Male

Ultra Male

JR Type Female

Yellow Input Cable Yellow OutPut Cable

Failsafe Pin

Barrel Switch

Gray Cable

BLUE LED

Blue Cable

Smart

Display

Smart

Display

General Usage and Screen Informaon

Important: The Smart Display that is supplied with the Smart Switch is a touch screen

display. It is used in both setup and provide feedback to the user about baery voltage and

milliamps used. The screen was designed to be mounted in a model for quick and easy use.

However it can be removed and plugged in when necessary.

Smart Screen

Baery 1 and Baery 2

Shows input voltage of both packs.

Total mA

Shows total milliamps since last charge.

Press here to enter the Main Menu

Last mA

Shows milliamps since model has been pow-

ered, resets when model is turned o. Press

here to reset ight mer and Last mA.

FL-T

Flight mer since model was turned on.

FL-N

Flight number since reset.

Baery Indicators

Shows the remaining capacity in the baeries

from 100% - 0%. NEVER FLY IF THE INDICATORS

ARE IN THE RED.

Main Menu

Return

Takes you back to the previous screen.

Power

Press here to go to the baery setup and

reset menu.

System

Pressing here will take you to the screen

calibraon and credits.

Below is an overview of each screen on the Smart Switch

Power Setup

Return

Takes you back to the previous screen.

RES-mA

Resets total mA used. Please ensure both packs

are FULLY charged before reset.

RES-FLT

Resets ight counter and mer to zero.

Bat Chemistry

Shows the baery chemistry you are using in the

model. We will go through how to set this in the

First Time Setup secon on page 10.

Bat Capacity mA

Shows the capacity of the baeries you are us-

ing. We will go through how to set this in the

First Time Setup secon on page 10.

Display Style

Switch between Baery or Bar images on the

smart screen. For more informaon see

“addional screens” on page 13.

System

Return

Takes you back to the previous screen.

Calibrate

Takes you to Screen calibraon. For more

informaon see page 12.

Credit

Shows credits screen.

First Time Setup

We are now going to go proceed with a rst me setup of the Smart Switch . Please en-

sure your baeries are fully charged before you setup the smart switch. If you need any

addional help with what each buon or item does please read the General Usage and

Screen informaon page located on page 7 of this manual.

Step 1

Ensure that both baeries are plugged into

the Smart Switch. You will also need to en-

sure the smart display is plugged into the

switch as it is used for programming.

Upon start up, you will see the AR logo.

Aer a few seconds the Smart Screen will

be shown.

Step 2

Using your nger, press the green Total mA

text on the smart display.

Step 3

You should now see the Main Menu

Screen. Press the yellow Power

buon on the screen.

Step 4

This is the baery setup screen. Using the arrows

(<, >)next to Bat Chemistry cycle through unl you

see the chemistry you are using with the switch.

The Smart Switch works with both 2S (6.0V—8.4v)

and 3S (10.8—12.8V) packs The Opons are Lipo,

Li-ion, Life, NiCd, NiMH.

Note: When seng the chemistry, ensure you

select the correct voltage and chemistry, other-

wise you will get a false low voltage warning (see

page 11).

Step 5

Using the + and - buons, set the capacity to the

capacity shown on your baery packs.

Note: Step 5 is extremely important, Please en-

sure the capacity is set correctly to the baery

packs you are using.

Step 6

Once you have set these up, press the RETURN

buon to take you back to the main menu. Press

RETURN again to go back to the Smart Screen.

You have successfully setup the Smart Switch.

Important

The Smart display shows how much capacity you have le using the baery indicators on

the le and right of the baery screen It is important that the capacity you enter is correct

and accurate. If you are unsure about the capacity of your baeries or if your packs are not

new. We recommend cycling your packs by discharging them and recharging them to full.

This will give you the best possible result for the baery packs you are using.

Inhaltsverzeichnis

Beliebte Bedienfeld Handbücher anderer Marken

RDZ

RDZ PC-HRX Bedienungsanleitung

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Technisches Handbuch

Efka

Efka Variocontrol V810 Bedienungsanleitung

Cebora

Cebora 208-10 Bedienungsanleitung

AMX

AMX AutoPatch CP-15 Bedienungsanleitung

Satel

Satel CA-6 KLED-S Bedienungsanleitung

Evolution

Evolution IQ plus 800 Bedienungsanleitung

Fagor

Fagor 8040 TCO CNC Bedienungsanleitung

Trane

Trane ComfortLink II XL950 Control Bedienungsanleitung

AKO

AKO PROCool AKO-17635-2 Bedienungsanleitung

ABB

ABB 6136/30M-101 Bedienungsanleitung

Telikou

Telikou BK-603 Belt Pack Bedienungsanleitung

Mapei

Mapei Mapeheat Thermo Touch Bedienungsanleitung

Bosch

Bosch D9412GV4 Bedienungsanleitung

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Bedienungsanleitung

Sminn

Sminn BOX L VF1L EI Bedienungsanleitung

Balboa

Balboa TP600 Bedienungsanleitung

Nice

Nice HSCU1 Technische Daten