Advantech USB-4716 Bedienungsanleitung

User Manual

USB-4716

200 kS/s, 16-bit, USB Multifunction

Module

USB-4716 User Manual ii

The documentation and the software included with this product are copyrighted 2021

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right

to make improvements in the products described in this manual at any time without

notice. No part of this manual may be reproduced, copied, translated or transmitted

in any form or by any means without the prior written permission of Advantech Co.,

Ltd. Information provided in this manual is intended to be accurate and reliable. How-

ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-

ments of the rights of third parties, which may result from its use.

Acknowledgments

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

Part No. 2003471602 Edition 3

Printed in China December 2021

iii USB-4716 User Manual

Product Warranty (2 years)

Advantech warrants the original purchaser that each of its products will be free from

defects in materials and workmanship for two years from the date of purchase.

This warranty does not apply to any products that have been repaired or altered by

persons other than repair personnel authorized by Advantech, or that have been sub-

ject to misuse, abuse, accident, or improper installation. Advantech assumes no lia-

bility under the terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most

customers never need to use our repair service. If an Advantech product is defective,

it will be repaired or replaced free of charge during the warranty period. For out-of-

warranty repairs, customers are billed according to the cost of replacement materials,

service time, and freight. Please consult your dealer for more details.

If you believe your product is defective, follow the steps outlined below.

1. Collect all the information about the problem encountered. (For example, CPU

speed, Advantech products used, other hardware and software used, etc.) Note

anything abnormal and list any onscreen messages displayed when the prob-

lem occurs.

2. Call your dealer and describe the problem. Have your manual, product, and any

relevant information readily available.

3. If your product is diagnosed as defective, obtain a return merchandize authori-

zation (RMA) number from your dealer. This allows us to process your return

more quickly.

4. Carefully pack the defective product, a completed Repair and Replacement

Order Card, and a proof of purchase date (such as a photocopy of your sales

receipt) into a shippable container. Products returned without proof of purchase

date are not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid

to your dealer.

Declaration of Conformity

This product has passed the CE test for environmental specifications when shielded

cables are used for external wiring. We recommend the use of shielded cables. This

type of cable is available from Advantech. Contact your local supplier for ordering

information.

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Opera-

tion of this equipment in a residential area is likely to cause harmful interference. In

such cases, users are required to correct the interference at their own expense.

USB-4716 User Manual iv

Technical Support and Assistance

1. Visit the Advantech website at www.advantech.com/support to obtain the latest

product information.

2. Contact your distributor, sales representative, or Advantech customer service

center for technical support if you need additional assistance. Please have the

following information ready before calling:

–Product name and serial number

–Description of your peripheral attachments

–Description of your software (operating system, version, application software,

etc.)

–A complete description of the problem

–The exact wording of any error messages

Document Feedback

To assist us with improving this manual, we welcome all comments and constructive

criticism. Please send all feedback in writing to [email protected].

Warnings, Cautions, and Notes

Warning! Warnings indicate conditions that if not observed can cause personal

injury!

Caution! Cautions are included to prevent hardware damage and data losses.

E.g.

“Batteries are at risk of exploding if incorrectly installed. Replace the bat-

tery only with the same or equivalent type as recommended by the man-

ufacturer. Discard used batteries according to the manufacturer's

instructions.”

Note! Notes provide additional optional information.

v USB-4716 User Manual

Safety Instructions

1. Read these safety instructions carefully.

2. Retain this user manual for future reference.

3. Disconnect the equipment from all power outlets before cleaning. Use only a

damp cloth for cleaning. Do not use liquid or spray detergents.

4. For pluggable equipment, the power outlet socket must be located near the

equipment and easily accessible.

5. Protect the equipment from humidity.

6. Do not expose the equipment to direct sunlight, or install the equipment in an

environment with direct sunlight, as this may cause damage.

7. Place the equipment on a reliable surface during installation. Dropping or letting

the equipment fall may cause damage.

8. The openings on the enclosure are for air convection. Protect the equipment

from overheating. Do not cover the openings.

9. Ensure that the voltage of the power source is correct before connecting the

equipment to a power outlet.

10. Position the power cord away from high-traffic areas. Do not place anything over

the power cord.

11. All cautions and warnings on the equipment should be noted.

12. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage from transient overvoltage.

13. Be aware that the rear cover may become quite hot during operation. To avoid

scalding or personal injury, do not touch the rear cover.

14. Never pour any liquid into an opening. This may cause fire or electric shock.

15. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

16. If one of the following occurs, have the equipment checked by qualified service

personnel:

The power cord or plug is damaged.

Liquid has penetrated the equipment.

The equipment has been exposed to moisture.

The equipment is malfunctioning or does not work according to the user

manual.

The equipment has been dropped and damaged.

The equipment shows obvious signs of breakage.

17. Do not leave the equipment in an environment with a storage temperature of

below -30 °C (-22 °F) or above 70 °C (158 °F) as this may cause damage. The

equipment should be located in a controlled environment.

18. Batteries are at risk of exploding if incorrectly replaced or installed. Replace only

with the same or equivalent type recommended by the manufacturer. Discard

used batteries according to the manufacturer’s instructions.

19. The equipment is intended to be installed on a wall or in a cabinet with the fol-

lowing conditions: access is restricted to service personnel or users who are

aware of all precautions that must be taken when using the equipment; access

can only be gained with the use of a key or other means of security; access is

controlled by the authority responsible for the location.

20. In accordance with the IEC 704-1:1982 specifications, the sound pressure level

at the operator’s position does not exceed 70 dB (A).

21. DISCLAIMER: These instructions are provided in accordance with IEC 704-1

specifications. Advantech disclaims all responsibility for the accuracy of any

statements contained herein.

USB-4716 User Manual vi

vii USB-4716 User Manual

Contents

Chapter 1 Introduction..........................................1

1.1 Features .................................................................................................... 2

1.2 Software Overview.................................................................................... 2

Chapter 2 Installation............................................3

2.1 Unpacking ................................................................................................. 4

2.2 Driver Installation ...................................................................................... 5

2.3 Hardware Installation ................................................................................ 6

Chapter 3 Signal Connections .............................7

3.1 Overview ................................................................................................... 8

3.2 I/O Connectors.......................................................................................... 8

3.2.1 Pin Assignment ............................................................................. 8

Figure 3.1 I/O Connector Pin Assignment ................................... 8

3.2.2 I/O Connector Signal Description.................................................. 9

Table 3.1: I/O Connector Signal Description ............................... 9

3.2.3 LED Indicator Status Description .................................................. 9

Table 3.2: LED Indicator Status Description................................ 9

3.3 Analog Input Connections....................................................................... 10

3.3.1 Single-ended Channel Connections ........................................... 10

Figure 3.2 Single-Ended Input Channel Connection ................. 10

3.3.2 Differential Input Connections..................................................... 11

Figure 3.3 Differential Input Channel Connection...................... 11

3.4 Analog Output Connections (Voltage)..................................................... 12

Figure 3.4 Analog Output Channel Connections ....................... 12

3.5 Trigger Source Connections ................................................................... 12

3.5.1 Internal Pacer Trigger Connection .............................................. 12

3.5.2 External Trigger Source Connection........................................... 12

3.6 Field Wiring Considerations .................................................................... 13

Appendix A Specifications ....................................15

A.1 Analog Input............................................................................................ 16

A.2 Analog Output ......................................................................................... 16

A.3 Non-Isolated Digital Input/Output ............................................................ 17

A.4 Counter ................................................................................................... 17

A.5 General ................................................................................................... 17

USB-4716 User Manual viii

Chapter 1

1Introduction

This chapter will provide informa-

tion on the features of the DAS

module, a quick start guide for

installation, and some brief infor-

mation on software and accesso-

ries for the USB-4716 Module.

Section include:

 Features

 Software Overview

USB-4716 User Manual 2

1.1 Features

Thank you for buying the Advantech USB-4716 data acquisition (DAS) module for

USB port. It features a unique circuit design and complete functions for data acquisi-

tion and control.

USB-4716 has the following measurement & control functions:

16 single-ended/ 8 differential or combination analog input channels

16-bit resolution A/D converter, with up to 200 kS/s sampling rate

8 digital input & 8 digital output channels (TTL Level)

2 analog output channels

16-bit programmable counter/timer x 1

Programmable gain for each analog input channel

Automatic channel/gain scanning

Onboard 1K samples FIFO buffer for AI channels

Bus-powered

Device status LED indicator

Removable on-module wiring terminal

Supports USB 3.0 SuperSpeed

Auto calibration function

Hot swappable

1.2 Software Overview

Advantech offers device drivers, SDKs, third-party driver support and application

software to help fully exploit the functions of your DAQ system. All these software

packages are available on the Advantech website: http://www.advantech.com/.

The Advantech Navigator is a utility that allows you to set up, configure and test

your device, and later stores your settings in a proprietary database.

1. To set up the I/O device for your card, you should first run the Advantech Navi-

gator program (by accessing Start/Programs/Advantech Automation/DAQNavi/

Advantech Navigator).

2. You can then view the device(s) already installed on your system (if any) on the

installed device tree view. If the software and hardware installation are com-

pleted, you will see USB modules in the installed devices list.

DAQNavi SDK is a software development kit for programming applications with

Advantech DAQ products. The necessary runtime DLL, header files, software

manual and tutorial videos can all be installed via XNavi installer. They can be

found under C:\Advantech\DAQNavi (default directory) after finishing the instal-

lation.

Note! The USB chip on your system may have a limitation on the number of

USB devices it will support. Normally, only five USB-4716 devices can

be supported.

Note! The power output of an USB port is 500 mA, while the USB-4716

requires 360 mA (typical). This means that if an USB hub is used, it will

need an external power supply to support more than one USB-4716

device.

Andere Handbücher für USB-4716

Inhaltsverzeichnis

Andere Advantech Steuereinheit Handbücher

Advantech

Advantech SOM-4466 Bedienungsanleitung

Advantech

Advantech PCM-3531 Installations- und Betriebshandbuch

Advantech

Advantech PCM-233A Installations- und Betriebshandbuch

Advantech

Advantech USB-4711A Bedienungsanleitung

Advantech

Advantech AMAX-4800 Series Bedienungsanleitung

Advantech

Advantech SOM-5894 Bedienungsanleitung

Advantech

Advantech PCM-3526 Installations- und Betriebshandbuch

Advantech

Advantech B+B SmartWorx iMcV-Giga-MediaLinX TX/SFP Bedienungsanleitung

Advantech

Advantech IPMI-1000 Installations- und Betriebshandbuch

Advantech

Advantech MOS-1130Y-0201E Bedienungsanleitung

Advantech

Advantech B+B SmartWorx IE-iMcV-2xLIM Bedienungsanleitung

Advantech

Advantech PCM-3116 Installations- und Betriebshandbuch

Advantech

Advantech PCM-3347 Series Bedienungsanleitung

Advantech

Advantech SOM-5962 Bedienungsanleitung

Advantech

Advantech PCM-3117 Installations- und Betriebshandbuch

Advantech

Advantech PCM-3665 PC/104-Plus Installations- und Betriebshandbuch

Advantech

Advantech PCL-832 Bedienungsanleitung

Advantech

Advantech ADAM-2000 Series Bedienungsanleitung

Advantech

Advantech ADAM-5000 Series Bedienungsanleitung

Advantech

Advantech PCM-3612I Installations- und Betriebshandbuch

Advantech

Advantech EPD-130 Bedienungsanleitung

Advantech

Advantech MIO-6254 Installations- und Betriebshandbuch

Advantech

Advantech ADAM-3017 Installations- und Betriebshandbuch

Advantech

Advantech PCM-3614I Installations- und Betriebshandbuch

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung