Advantech POC-195 Bedienungsanleitung

POC-195

Point-of-Care Terminal with 19"

TFT LCD

User Manual

POC-195 User Manual ii

The documentation and the software included with this product are copy-

righted 2007 by Advantech Co., Ltd. All rights are reserved. Advantech

Co., Ltd. reserves the right to make improvements in the products

described in this manual at any time without notice. No part of this man-

ual may be reproduced, copied, translated or transmitted in any form or

by any means without the prior written permission of Advantech Co., Ltd.

Information provided in this manual is intended to be accurate and reli-

able. However, Advantech Co., Ltd. assumes no responsibility for its use,

nor for any infringements of the rights of third parties, which may result

from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft

Corp.

All other product names or trademarks are properties of their respective

owners.

Part No. 2006019500 Edition 1

Printed in Taiwan March 2007

iii

Declaration of Conformity

FCC Class B

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harm-

ful interference when the equipment is operated in a residential environ-

ment. This equipment generates, uses and can radiate radio frequency

energy. If not installed and used in accordance with this user's manual, it

may cause harmful interference to radio communications.

Note that even when this equipment is installed and used in accordance

with this user's manual, there is still no guarantee that interference will

not occur. If this equipment is believed to be causing harmful interference

to radio or television reception, this can be determined by turning the

equipment on and off. If interference is occurring, the user is encouraged

to try to correct the interference by one or more of the following mea-

sures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from

that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Warning! Any changes or modifications made to the equip-

ment which are not expressly approved by the

relevant standards authority could void your

authority to operate the equipment.

Caution! Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equiva-

lent type recommended by the manufacturer.

Dispose of used batteries according to the man-

ufacturer's instructions.

POC-195 User Manual iv

Additional Information and Assistance

1. Visit the Advantech websites at www.advantech.com or

www.advantech.com.tw where you can find the latest information

about the product.

2. Contact your distributor, sales representative, or Advantech's cus-

tomer service center for technical support if you need additional

assistance. Please have the following information ready before you

call:

– Product name and serial number

– Description of your peripheral attachments

– Description of your software (operating system, version, appli-

cation software, etc.)

– A complete description of the problem

– The exact wording of any error messages

This equipment is a source of electromagnetic waves. Before use please,

make sure that there are not EMI sensitive devices in its surrounding

which may malfunction therefore.

Warning! 1. Input voltage rated 100-240 VAC, 50-60 Hz, 4-

2 A (AC Mode)

2. Use a 3 V @ 195 mA lithium battery (Model

No. BR2032)

3. Packing: please carry the unit with both

hands, handle with care

4. Our European representative:

Advantech Europe GmbH

Kolberger Strasse 7

D-40599 Dusseldorf, Germany

Tel: 49-211-97477350

Fax: 49-211-97477300

5. Maintenance: to properly maintain and clean

the surfaces, use only approved products or

clean with a dry applicator

Packing List

Before installing your Point of Care Terminal, ensure that the following

materials have been received:

• POC-195 series Point of Care Terminal

• User manual

• Accessories for POC-195

– Y-shaped adapter for PS/2 mouse and keyboard

– Power cord (1.8 m) - USA type (UK, German types are avail-

able on request)

– “Drivers and Utilities” CD-ROM disc

– Mounting kits and packet of screws

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User's Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning.

Use a damp cloth. Do not use liquid or spray detergents for clean-

ing.

4. For plug-in equipment, the power outlet socket must be located

near the equipment and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Drop-

ping it or letting it fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before con-

necting the equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not

place anything over the power cord.

Warning! To prevent electric shock, Do not remove cover.

No user serviceable parts inside, refer servicing

to qualified personnel.

POC-195 User Manual vi

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the

power source to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or elec-

trical shock.

13. Never open the equipment. For safety reasons, the equipment

should be opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked

by service personnel:

a The power cord or plug is damaged.

b Liquid has penetrated into the equipment.

c The equipment has been exposed to moisture.

d The equipment does not work well, or you cannot get it to work

according to the user's manual.

e The equipment has been dropped and damaged.

f The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED

ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS

BELOW -20°C (-4°F) OR ABOVE 60°C (140°F). THIS MAY

DAMAGE THE EQUIPMENT.

16. If your computer is losing dramatic time or the BIOS configuration

reset to default, the battery has no power.

17. IMPROPER INSTALLATION OF VESA MOUNTING CAN

RESULT IN SERIOUS PERSONAL INJURY! VESA mount

installation should be operated by professional technician, please

contact the service technician or your retail if you need this service.

Caution! 1. Do not replace battery yourself. Please con-

tact a qualified technician or your retail.

2.The computer is provided with a battery-pow-

ered real-time clock circuit. There is a danger of

explosion if battery is incorrectly replaced.

Replace only with same or equivalent type rec-

ommended by the manufacture. Discard used

batteries according to the manufacturer's instruc-

tions

vii

18. CLASSIFICATION:

Supply Class I adapter

No applied part

IPX1

Continuous Operation

Not AP or APG category

19. Disconnect device: Appliance inlet.

20. Follow the national requirement to dispose unit.

21. Maintenance: to properly maintain and clean the surfaces, use only

the approved products or clean with a dry applicator.

22. Contact information:

No.1, Alley 20, Lane 26, Reuiguang Road Neihu District, Taipei,

Taiwan 114, R.O.C.

TEL: (02)27927818

23.

23. This equipment shall not be used for life support system.

24. Accessory equipment connected to the analog and digital interfaces

must be in compliance with the respective nationally harmonized

IEC standards (i.e. IEC 60950 for data processing equipment, IEC

60065 for video equipment, IEC 61010-1 for laboratory equipment,

and IEC 60601-1 for medical equipment.) Furthermore all configu-

rations shall comply with the system standard IEC 60601-1-1.

Everybody who connects additional equipment to the signal input

part or signal output part configures a medical system, and is there-

fore, responsible that the system complies with the requirements of

the system standard IEC 60601-1-1. The unit is for exclusive inter-

connection with IEC 60601-1 certified equipment in the patient

environment and IEC 60XXX certified equipment outside of the

patient environment. If in doubt, consult the technical services

department or your local representative.

25. User not to contact SIP/SOPs and the patient at the same time.

POC-195 User Manual viii

26. The sound pressure level at the operator's position according to IEC

704-1:1982 is no more than 70dB (A).

DISCLAIMER

This set of instructions is given according to IEC 704-1. Advantech dis-

claims all responsibility for the accuracy of any statements contained

herein.

Contents

Chapter 1 General Information ........................................2

1.1 Introduction ....................................................................... 2

1.2 Specifications .................................................................... 2

1.2.1 General............................................................................ 2

1.2.2 Standard PC functions .................................................... 3

1.2.3 Flat panel interface.......................................................... 3

1.2.4 Audio function ................................................................ 4

1.2.5 Ethernet interface............................................................ 4

1.2.6 Optional modules............................................................ 4

1.2.7 Touchscreen (optional) ................................................... 5

Table 1.1 Touchscreen specifications....................... 5

1.2.8 Environment.................................................................... 5

1.3 Cleaning/Disinfecting........................................................ 6

1.4 LCD Specifications ........................................................... 6

1.5 Dimensions........................................................................ 7

Figure 1.1 Dimensions of the POC-195..................... 7

Chapter 2 System Setup...................................................10

2.1 A Quick Tour of the POC-195 ........................................ 10

Figure 2.1 Front View.............................................. 10

Figure 2.2 Left side view ......................................... 10

Figure 2.3 Rear view................................................ 11

2.2 Installation Procedures .................................................... 12

2.2.1 Connecting the power cord ........................................... 12

Figure 2.4 Connecting the power cord..................... 12

2.2.2 Connecting the keyboard and mouse ............................ 12

2.2.3 Switching on the power ................................................ 12

2.3 Running the BIOS Setup Program .................................. 13

2.4 Installing System Software.............................................. 13

2.5 Installing the Drivers....................................................... 14

Figure 2.5 “Drivers and Utilities” CD-ROM directory

structure .................................................. 14

Chapter 3 Graphic Chipset Setup...................................16

3.1 Introduction ..................................................................... 16

3.1.1 Chipset .......................................................................... 16

3.1.2 Display memory............................................................ 16

3.1.3 LVDS transmitter.......................................................... 16

3.1.4 Display types................................................................. 16

3.2 Installation of Graphic Driver ......................................... 17

3.2.1 Installation for Windows XP ........................................ 18

3.3 Further Information......................................................... 22

POC-195 User Manual x

Chapter 4 Audio Interface...............................................24

4.1 Introduction ..................................................................... 24

4.2 Installation of Audio Driver ............................................ 24

4.2.1 Installation for Windows 2000/XP ............................... 24

4.3 Further Information......................................................... 26

Chapter 5 Touchscreen Interface ...................................28

5.1 Introduction ..................................................................... 28

5.1.1 General Information...................................................... 28

5.1.2 General Specifications .................................................. 28

5.1.3 Environmental Specifications ....................................... 28

5.2 Installation of Touchscreen Driver.................................. 29

5.2.1 Installation for Windows XP ........................................ 29

5.3 Further Information......................................................... 35

Chapter 6 PCI Express Ethernet Interface....................38

6.1 Introduction ..................................................................... 38

6.2 Installation of Ethernet Driver......................................... 38

6.2.1 Installation for Windows XP ........................................ 38

6.3 Further Information......................................................... 40

Inhaltsverzeichnis

Andere Advantech Touch-Terminal Handbücher

Advantech

Advantech USC-360 Installations- und Betriebshandbuch

Advantech

Advantech TREK-723 Bedienungsanleitung

Advantech

Advantech EH-7104G Bedienungsanleitung

Advantech

Advantech POC-S199 Series Bedienungsanleitung

Advantech

Advantech POC-WP21 Series Bedienungsanleitung

Advantech

Advantech POC-W152 Bedienungsanleitung

Advantech

Advantech POC-W211 Bedienungsanleitung

Advantech

Advantech POC-176 Bedienungsanleitung

Advantech

Advantech WP-5530-PD10 Bedienungsanleitung

Advantech

Advantech TREK-722 Bedienungsanleitung

Advantech

Advantech ADAM-3600-C2G Series Bedienungsanleitung

Advantech

Advantech UbiQ-480 Bedienungsanleitung

Advantech

Advantech ADAM-3952/PMA Bedienungsanleitung

Advantech

Advantech WP-75**-**10/40 Bedienungsanleitung

Advantech

Advantech POC-S175 Bedienungsanleitung

Advantech

Advantech ADAM-3968M/PMA Installations- und Betriebshandbuch

Advantech

Advantech TREK-773 Bedienungsanleitung

Advantech

Advantech POC-W213L Series Bedienungsanleitung

Advantech

Advantech WebOP-3000 Series Bedienungsanleitung

Advantech

Advantech UPOS-211 Bedienungsanleitung

Advantech

Advantech TREK-725 Bedienungsanleitung

Advantech

Advantech HIT-W18 Series Bedienungsanleitung

Advantech

Advantech POC127 Bedienungsanleitung

Advantech

Advantech UPOS-3150 Bedienungsanleitung

Beliebte Touch-Terminal Handbücher anderer Marken

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Bedienungsanleitung

Ingenico

Ingenico AXIUM EX4000 Bedienungsanleitung

Heisei Electronics

Heisei Electronics Q-POS 815 Bedienungsanleitung

Amano

Amano MTX-15 Bedienungsanleitung

FLOWBIRD

FLOWBIRD CWT Compact Touch Bedienungsanleitung

Demco

Demco SP7 Bedienungsanleitung

Lathem

Lathem PC600 Series Bedienungsanleitung

Partner

Partner MF-2352 Bedienungsanleitung

NCR

NCR RealPOS 7460-2 Handbuch

Simrad

Simrad MS50 Montageanleitung

Unitech

Unitech MR350 MKII Kurzanleitung

Jungheinrich

Jungheinrich WMT 210 Bedienungsanleitung

Motorola

Motorola MTP850 Bedienungsanleitung

YASKAWA

YASKAWA 62H-MDC0 Bedienungsanleitung

MVG industries

MVG industries NeptuLink Bedienungsanleitung

Price Industries Limited

Price Industries Limited FDC Gebrauchsanweisung

Honeywell

Honeywell TemaKey Bedienungsanleitung

EBN

EBN BPC65-B-A16G Bedienungsanleitung