AEG AMP 4 Bedienungsanleitung

Antenna multiplexer AMP 4/8

Installation guide

--------------------------------------------------------------------------------2/20--------------------------------------------------------------------------------

1INTRODUCTION ............................................................................................................ 4

2INSTALLATION............................................................................................................. 4

2.1 Mounting of the housing ............................................................................................................................4

2.2 Grounding of the AMP 4/8 ........................................................................................................................4

2.3 Connecting of the plug...............................................................................................................................5

2.4 Connecting of the power supply cable ........................................................................................................6

2.4.1 Using the connecting cable for AMP und ARE i2 (RS232) .................................................................6

2.4.2 Using the switchboard cable for AMP (RS232) ..................................................................................6

2.4.3 Using the switchboard cable for AMP (binär).....................................................................................6

2.4.4 Using a self assembled connecting cable.............................................................................................7

2.4.4.1 Assembling of the cable pipe........................................................................................................7

2.4.4.2 Mounting of the cable .................................................................................................................7

2.4.4.3 Pin assignment of the SAB connector ..........................................................................................9

3VISUAL SIGNAL LAMPS ............................................................................................ 10

4INSTRUCTION SET / STRUCTURE OF THE INSTRUCTION SET...............................10

4.1 Generall..................................................................................................................................................10

4.1.1 Entering instructions........................................................................................................................11

4.1.2 Incorrect instruction / error codes ....................................................................................................11

4.1.3 Upper and lower case ......................................................................................................................11

4.2 Change of the mode ................................................................................................................................12

4.3 Changing the channel ..............................................................................................................................12

4.4 Version ...................................................................................................................................................12

4.5 Initialiation with default parameters .......................................................................................................12

4.6 Saving of the parameters ........................................................................................................................13

4.7 Changing the baudrate ............................................................................................................................13

4.8 Warmstart with saved parameters ...........................................................................................................13

5SYSTEM OVERVIEW .................................................................................................. 14

5.1 Controlling via RS232/USB (mode 1)......................................................................................................14

5.2 Controlling via reader ARE i2 (mode 2) ..................................................................................................15

5.3 Controlling via digital inputs (mode 3).....................................................................................................16

--------------------------------------------------------------------------------3/20--------------------------------------------------------------------------------

6STARTUP AND TESTING THE AMP 4/8 ....................................................................17

7HOTLINE .....................................................................................................................18

8REVISIONS ................................................................................................................. 18

9ANHANG...................................................................................................................... 19

--------------------------------------------------------------------------------4/20--------------------------------------------------------------------------------

1Introduction

This document will describe the components of the AMP 4/8 and the procedure how to do the first

set up of the reader.

The main features of the reader are listed below:

up to 8 antennas connectable

integrated RS232 or USB interface

3 different types of controlling possible (RS232/USB, with the reader ARE i2, with digital in-

puts)

power supply from 9V DC to 30V DC (see chapter 2.3)

compact housing

the protection class of the housing is IP65

2Installation

To ensure a proper function of the AMP 4/8 you have to follow the steps in following chapters. The

installation should be done by trained people.

2.1 Mounting of the housing

The AMP 4/8 can be mounted to any other mechanic construction. It is recommended to protect the

housing against heavy mechanical interactions and drippy fluids.

With the help of the plastic bars, the reader can be mounted or screwed on to the most fastening

elements without open the housing of the device.

2.2 Grounding of the AMP 4/8

The AMP 4/8 should be grounded. The connector is placed at the side of the housing (6.35 mm flat

contact).

To avoid EMV-problems, the cable to ground ought to be very short with low impedance.

--------------------------------------------------------------------------------5/20--------------------------------------------------------------------------------

Attention!

The topology of the ground wires must be done in the right way (according state of art).

2.3 Connecting of the plug

Attention!

Be sure that the grounding of the reader is well done and the power supply is not connect-

ed(chapter 3.2). Otherwise the electronic may be destroyed by electrostatic discharge (ESD).

Figure 1: connecting the plug

Put on the sealing 2 to the SAB Cab (A).

Plug in the SAB Cab to the connector at the bottom of the reader device (B).

There is only one way to plug in the SAB Cab to the connector rim of the reader.

Fasten the SAB Cab with the help of the screws.

To meet the protection class of IP 65, it’s necessary to apply a turning moment of 0.5 Nm to the

screws.

--------------------------------------------------------------------------------6/20--------------------------------------------------------------------------------

2.4 Connecting of the power supply cable

The reader has to be supplied with 9..30V DC. The maximum output power of the power supply has

to be 1.2 Watt. Be sure that you use the right polarity.

It is very important to power the AMP with a clean ground (without any electrical interferences).

The best way is, to use the same ground as the reading system.

2.4.1 Using the connecting cable for AMP und ARE i2 (RS232)

Power supply: brown = + 9 .. 30 Volt

white = ground

2.4.2 Using the switchboard cable for AMP (RS232)

Power supply: brown = + 9 .. 30 Volt

white = ground

Interface: green = RXD (Dataout AMP 4/8)

yellow = TXD (Dataout AMP 4/8)

grey = ground

2.4.3 Using the switchboard cable for AMP (binär)

Power supply: brown = + 9 .. 30 Volt

white = ground

binary control: green = B0

yellow = B1

grey = B2

pink = B3

--------------------------------------------------------------------------------7/20--------------------------------------------------------------------------------

2.4.4 Using a self assembled connecting cable

Using the following SAB cabs you can assemble your own connecting cable.

ID 70211

SAB cab with 1 PG9 cable pipe

ID 70215

SAB cab with 2 pre-assembled cable pipes

ID 70219

SAB cab without any cable pipe

You can use any shielded five-pole cable. The allowed diameter of the cable must be in the range

from 3,5 to 8mm. For this case, IP 65 is reached.

Attention!

The minimum voltage at the readers input mustn’t be lower then 9V.

The maximum length of the serial RS232 cable is 15m.

2.4.4.1 Assembling of the cable pipe

Breakthrough the prepared areas at the surface of the SAB Cabs. There are two prepared areas seen

at the SAB Cab: central and at one side of the cab.

The o-ring (3) has to be assembled proberly to the cable pipe (4) to ensure the protection class IP

65.

Figure 2 Assembling of the cable pipe

Bring the nut (2) of the cable pipe inside of the SAB Cab (1).

To fasten the nut please use the right tool (17mm).

2.4.4.2 Mounting of the cable

The cable must be mounted in following steps:

--------------------------------------------------------------------------------8/20--------------------------------------------------------------------------------

Cable

Remove all inner parts from the cable pipe at the SAB Cab (1) ( nut (5), cable fastener (3), pipe(4))

(see Figure 4)

Put all the removed parts (nut (5), cable fastener (3), pipe (4),) and the cable pipe of the SAB Cab

as well (1 to 4) to the cable.

Figure 3 Mounting for the cable

Remove the outer isolation of the cable at a length of 6cm .

Remove the isolation of the wires at a length of 6mm and stick a covering hull to the litz wire.

Put the cable to the cable pipe. The length of the cable coming out the SAB Cab must long enough to

do all further installation steps in an easy way.

Stick the pipe (4) into the cable fastener (3).

Stick the cable fastener (3) into the cable pipe.

Connect the cables into the right places of the MINI-COMBICON-Connectors (6).

The pin assignment is shown in the figure below.

Put the MINI-COMBICON-Connectors into the SAB cab. Look after the color coding.

--------------------------------------------------------------------------------9/20--------------------------------------------------------------------------------

2.4.4.3 Pin assignment of the SAB connector

Figure 4: Pin assignment of the SAB connector

Connection between ARE i2 and AMP see document: Schematic diagram ARE i2 RS232 and

AMP RS232

AMP 4/8

B 0

B 1

B 2

Shield/VBus

B 3

V+ (+24V)

GND (0V)

TXD/D+

RXD/D-

Data

green

EV+

GND

TXD

RXD

Data line AMP/ARE i2

B0 (binary control, LSB)

+US1

-US1

black

+US2

-US2

B1 (binary control)

B2 (binary control)

B3 (binary control, MSB)

Schirm(RS232) / VBus(USB)

AMP 4/8

B 0

B 1

B 2

Shield/VBus

B 3

V+ (+24V)

GND (0V)

TXD/D+

RXD/D-

Data

gray

KV+

GND

TXD

RXD

Data line AMP/ARE i2

B0 (binary control, LSB)

+US

-US

blue

B1 (binary control)

B2 (binary control)

B3 (binary control, MSB)

Schirm(RS232) / VBus(USB)

--------------------------------------------------------------------------------10/20--------------------------------------------------------------------------------

AEG ID

Vcc

AMP4/8

3Visual signal lamps