AEG Protect alpha. 1200 Bedienungsanleitung

USER MANUAL

Uninterruptible Power Supply

Protect alpha. 1200

Protect alpha.

CONTENTS

1. Safety – caution ................................................................................. 3

2. Introduction ....................................................................................... 5

3. Trouble shooting................................................................................ 6

4. System description ............................................................................ 7

4.1. Inspection ......................................................................................................... 7

4.2. Charging ...........................................................................................................8

4.3. Placement.........................................................................................................8

4.4. Connection .......................................................................................................9

4.5. Turn On/Off ......................................................................................................9

4.6. DC-start............................................................................................................. 9

4.7. Green Power Function.....................................................................................9

5. Speciﬁcation..................................................................................... 10

6. CE conformity .................................................................................. 11

• This UPS utilizes voltages that may be hazardous. Do not attempt to

disassemble the unit. The unit contains no user serviceable parts.

Only qualified service personnel may perform repairs.

• Internal battery voltage is 24 V DC. Sealed, lead-acid, 6 cell battery – two pcs.

• Connection to any other type of socket other than a two-pole, three-wire

grounded socket may result in shock hazard as well as violating local

electrical codes.

• In the event of an emergency, press the OFF button and disconnect

the power cord from the AC power supply to properly disable the UPS.

• Do not allow liquids or any foreign object to enter the UPS. Do not place

beverages or any other liquid-containing vessels on or near the unit.

• The unit is intended for installation in a controlled environment

(temperature controlled, indoor area free of conductive contaminants).

• Avoid installing the UPS in locations where there is standing or running

water, or excessive humidity.

• Do not plug the UPS input into its own output.

• Do not attach a power strip or surge suppressor to the UPS.

• Do not attach non-computer related items, such as medical equipment,

life-support equipment, microwave ovens, or vacuum cleaners to the UPS.

• To reduce the risk of overheating the UPS, do not cover the UPS’ cooling

vents and avoid exposing the unit to direct sunlight or installing the unit

near heat emitting appliances such as space heaters or furnaces.

• Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

• Do not dispose of batteries in a fire as they may explode.

• Do not open or damage the battery or batteries. Released electrolyte

is harmful to the skin and eyes and may be toxic.

• A battery can present a risk of electrical shock and high short circuit current.

• The following precautions should be observed when working on batteries:

1) Remove watches, rings, or other metal objects from hands.

2) Use tools with insulated handles.

3) Wear rubber gloves and boots.

4) Do not lay tools or metal parts on top of batteries.

5) Disconnect charging source prior to connecting or disconnecting

battery terminals.

1. SAFETY – CAUTION

• Servicing of batteries should be performed or supervised by personnel

trained in batteries and the required precautions. Keep unauthorized

personnel away from batteries.

• When replacing batteries, replace with the same number and type of sealed

lead-acid batteries. The maximum ambient temperature rating is 40°C.

• This pluggable type A equipment, with battery already installed by the

supplier, is operator installable and may be operated by non-technical users.

• During the installation of this equipment it should be assured that the

sum of the leakage currents of the UPS and the connected loads does

not exceed 3.5 mA.

• Attention, electric shock hazard. With disconnection of this unit from the

mains, hazardous voltage still may be accessible through the supply from

the battery. The battery supply should therefore be disconnected at the

positive and negative poles of the battery when maintenance or service

work inside the UPS is necessary.

• The mains socket outlet that supplies the UPS shall be installed near the

UPS and shall be easily accessible.

2. INTRODUCTION

This UPS is specially designed for Personal Computer use and has multiple

functions. Its light weight, compact design ﬁts perfectly to the limited working

environment. This line of UPS is equipped with boost and buck AVR to stabilize

input voltage range. It is also built-in with a DC-start function. This function

enables the UPS to be started without an AC power supply. Although it’s a

small UPS, the main features of the Protect alpha UPS are listed below:

• Microprocessor control guarantees high reliability

• Equipped with boost and buck AVR

• Green Power Function for energy saving

• DC-start function

• Auto-restart during AC recovery

• Compact size, light weight

• Provides AC overload protection

3. TROUBLE SHOOTING

Symptom Possible Cause Remedy

No LED display

on the front

panel

1. Battery weak 1. Charge battery for

up to 8 hours

2. Battery defective 2. Replace with the same

type of battery

3. Power switch is

not pressed

3. Press the power

switch again

Alarm buzzer

beeps continu-

ously when AC

supply is normal

Overload of the UPS Verify that the load matches

the UPS capability speciﬁed

in the specs

In event of

power failure,

back-up time

is shortened

1. Overload of the UPS 1. Remove some

non-critical load

2. Battery voltage is too low 2. Charge battery for 8 hours

or more

3. Battery defective due to

high temperature operation

environment, or improper

operation of battery

3. Replace with the same

type of battery

Mains normal

but LED is

ﬂashing

Power cord is loose Reconnect the power cord

properly

If any abnormal situations occur that are not listed above, please call service

personnel immediately.

4. SYSTEM DESCRIPTION

Front panel

1. Power switch

LED indicators:

2. Normal: Green

3. Battery mode: Yellow ﬂashing

4. AC mode: Green

5. Fault mode: Red

Back panel

1. AC input

2. Output sockets

3. USB & RJ45 communication

4.1. INSPECTION

Remove the UPS from its packaging and inspect it for damage that may

have occurred during shipping. If any damage is discovered, repack the

unit and return it to the place of purchase.

4.2. CHARGING

This unit is shipped from the factory with its internal battery fully charged,

however, some charge may be lost during shipping and the battery should

be recharged prior to use. Turn on the UPS, plug the unit into an appropriate

power supply and allow the UPS to charge fully by leaving it plugged in for

at least 6 hours with no load connected (i.e. no electrical devices such as

computers, monitors, etc.).

4.3. PLACEMENT

Install the UPS unit in any protected environment that provides adequate

airﬂow around the unit, and is free from excessive dust, corrosive fumes and

conductive contaminants. Do not operate your UPS in an environment where

the ambient temperature or humidity is high.

Locate the UPS at least 20 cm away from the monitor to avoid interference.

4.4. CONNECTION

Plug the UPS into a 2-pole, 3-wire grounded socket. Then connect one

computer-related device into each of the power sockets supplied on the

back of the UPS.

4.5. TURN ON/OFF

To turn on the UPS unit, press the power switch lightly.

To turn off the UPS unit, press the power switch again.

4.6. DC-START

All Protect alpha.UPSs are equipped with DC-start. To start the UPS

when AC utility power is not available, simply press the power switch.

4.7. GREEN POWER FUNCTION

All Protect alpha.UPSs are equipped with Green Power Function. For saving

power and protecting the battery, the method of deep discharging protection

is adopted in inverter mode.

5. SPECIFICATION

MODEL Protect alpha.1200

CAPACITY VA / W 1200 VA / 600 W

INPUT Voltage 120 V AC or 230 V AC

Voltage range 85 – 145 V AC or

170 – 280 V AC

OUTPUT Voltage

Voltage regulation

(battery mode)

±10 %

Frequency 50 Hz or 60 Hz

Frequency regulation ±1 Hz (battery mode)

Output waveform Modiﬁed sine wave

BATTERY Battery type 12 V 7 Ah x 2

Recharge time 6 hours to 90 % after complete

discharge

TRANSFER TIME Typical 4 – 8 ms

INDICATOR Normal Green LED

AC mode Green LED

Battery mode Yellow ﬂashing LED

Fault mode Red LED

AUDIBLE ALARM Backup mode Sounding every 10 seconds

Low battery Sounding every 1 second

Overload Sounding every 0.5 seconds

Fault Continuously sounding

PROTECTION Full protection Discharge, overcharge,

and overload protection

PHYSICAL Dimension (mm) 365 (L) x 139 (W) x 195 (H)

WEIGHT Net weight 8.6 kg

ENVIRONMENT Operating environment 0 °C – 40 °C

Noise level Less than 40 dB

120 V AC or 230 V AC

Inhaltsverzeichnis

Andere AEG UPS Handbücher

AEG

AEG Protect A. 1000 Bedienungsanleitung

AEG

AEG Protect 3.M 2.0 Bedienungsanleitung

AEG

AEG Protect NAS Betriebsanleitung

AEG

AEG PROTECT D LCD+ Bedienungsanleitung

AEG

AEG Protect C 1000 LCD+ Bedienungsanleitung

AEG

AEG Protect C.3000 Bedienungsanleitung

AEG

AEG CompuMaster 300 Bedienungsanleitung

AEG

AEG Protect A Series Bedienungsanleitung

AEG

AEG Protect D Series Bedienungsanleitung

AEG

AEG IST7 Bedienungsanleitung

AEG

AEG UPS 10 kVA Bedienungsanleitung

AEG

AEG MBS 6000 Bedienungsanleitung

AEG

AEG Protect A. 1400 Bedienungsanleitung

AEG

AEG PROTECT 1 LCD Bedienungsanleitung

AEG

AEG protect d. 1000 Bedienungsanleitung

AEG

AEG PROTECT C. 1000 (S) Bedienungsanleitung

AEG

AEG PROTECT A. 500 Bedienungsanleitung

AEG

AEG 600 KVA Bedienungsanleitung

AEG

AEG PROTECT C. 10000 Bedienungsanleitung

AEG

AEG PDU 10-1 Bedienungsanleitung

AEG

AEG Protect alpha 450 Bedienungsanleitung

AEG

AEG Protect 1. M Bedienungsanleitung

AEG

AEG Protect Home. 600 Bedienungsanleitung

AEG

AEG Protect 5.31 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung