INSTALLATION & MAINTENANCE INSTRUCTIONS
ACP COMPACT FLOODLIGHT
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
DRAWING NO. A71218 REV B (FRONT)
©2007 ACUITY LIGHTING GROUP, INC. PART NUMBER 057-70-71218
REMOVABLEREMOVABLE
PLUG PLUG
SCREWS (3)SCREWS (3)
CLAMPINGCLAMPING
BOLTS (2)BOLTS (2)
MOUNTING
HOLES
CLOSURE CLOSURE
SCREWS (2)SCREWS (2)
WARNING
ENSURE UNIT IS PROPERLY GROUNDED AND DISCONNECT POWER DURING INSTALLATION AND
BEFORE SERVICING TO AVOID THE RISK OF SEVERE OR FATAL ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
!
BOLT TO A MAXIMUM OF 400 INCH ILBS.BOLT TO A MAXIMUM OF 400 INCH ILBS.
RETIGHTEN BOLT TO SECURE TENON MOUNT.TIGHTENRETIGHTEN BOLT TO SECURE TENON MOUNT.TIGHTEN
ACP COMPACT FLOOD TO DESIRED ANGLE ANDACP COMPACT FLOOD TO DESIRED ANGLE AND
ANGLE. LOOSEN BOLT IN CENTER OF TENON MOUNTEDANGLE. LOOSEN BOLT IN CENTER OF TENON MOUNTED
INDICATED ON TENON FOR DETERMINING DESIREDINDICATED ON TENON FOR DETERMINING DESIRED
AND LOCK NUTS RETIGHTENED. INDEX MARKS AREAND LOCK NUTS RETIGHTENED. INDEX MARKS ARE
MADE. SET SCREWS SHOULD THEN BE RETIGHTENEDMADE. SET SCREWS SHOULD THEN BE RETIGHTENED
SHOULD BE LOOSENED AND HORIZONTAL ADJUSTMENTSHOULD BE LOOSENED AND HORIZONTAL ADJUSTMENT
THE SET SCREWS AND LOCK NUTSTHE SET SCREWS AND LOCK NUTS
TENON MOUNT:TENON MOUNT:
TO A MAXIMUM OF 400 INCH LBS.TO A MAXIMUM OF 400 INCH LBS.
MENT MADE AND THEN BOTH BOLTS RETIGHTENEDMENT MADE AND THEN BOTH BOLTS RETIGHTENED
YOKE NEED TO BE LOOSENED, VERTICAL ADJUST-YOKE NEED TO BE LOOSENED, VERTICAL ADJUST-
MOUNTING ANGLES. THE BOLTS ON EACH SIDE OFMOUNTING ANGLES. THE BOLTS ON EACH SIDE OF
EACH SIDE OF YOKE FOR DETERMINING DESIREDEACH SIDE OF YOKE FOR DETERMINING DESIRED
INDEX MARKS ARE INDICATED ONINDEX MARKS ARE INDICATED ON
YOKE MOUNT:YOKE MOUNT:
ADJUSTMENT:ADJUSTMENT:
PIPE TENON. TIGHTEN ALL FOUR SET SCREWS EQUALLY PIPE TENON. TIGHTEN ALL FOUR SET SCREWS EQUALLY
TO A MAXIMUM OF 350 INCH LBS., THEN TIGHTEN EACH TO A MAXIMUM OF 350 INCH LBS., THEN TIGHTEN EACH
LOCK NUT TO A MAXIMUM OF 350 INCH LBS. TO LOCK NUT TO A MAXIMUM OF 350 INCH LBS. TO
SECURELY ATTACH FIXTURE TO TENON TOP. SECURELY ATTACH FIXTURE TO TENON TOP.
TENON MOUNT CAN BE MOUNTED TO A 2" OR 2 1/2"TENON MOUNT CAN BE MOUNTED TO A 2" OR 2 1/2"
THE COMPACT FLOOD WITH OPTIONALTHE COMPACT FLOOD WITH OPTIONAL
TENON MOUNT:TENON MOUNT:
THE YOKE HAS 3 MOUNTING HOLES, THE YOKE HAS 3 MOUNTING HOLES,
ONE FOR A 3/4" BOLT AND TWO FOR 3/8" BOLTS. ONE FOR A 3/4" BOLT AND TWO FOR 3/8" BOLTS.
MOUNTING ADAPTORS ARE AVAILABLE TO ALLOW FORMOUNTING ADAPTORS ARE AVAILABLE TO ALLOW FOR
HORIZONTAL ADJUSTMENT ON POLE TOPS, CROSS HORIZONTAL ADJUSTMENT ON POLE TOPS, CROSS
ARMS, ETC. HORIZONTAL ADJUSTMENT MUST BE ARMS, ETC. HORIZONTAL ADJUSTMENT MUST BE
DETERMINED BEFORE MOUNTING THE YOKE TO THEDETERMINED BEFORE MOUNTING THE YOKE TO THE
CROSSARM IF THE ACP FLOOD IS BEING MOUNTED CROSSARM IF THE ACP FLOOD IS BEING MOUNTED
DIRECTLY TO A CROSSARM WITHOUT THOSE OPTIONALDIRECTLY TO A CROSSARM WITHOUT THOSE OPTIONAL
FITTERS.FITTERS.
YOKE MOUNT:YOKE MOUNT:
INSTALLATIONINSTALLATION
THIS UNIT HAS BEEN DESIGNED WITH THREE THIS UNIT HAS BEEN DESIGNED WITH THREE
BREATHING HOLES. TWO HOLES IN THE WIRING BREATHING HOLES. TWO HOLES IN THE WIRING
COMPARTMENT AREA AND 1 HOLES IN THE BEZEL. ALL COMPARTMENT AREA AND 1 HOLES IN THE BEZEL. ALL
HOLES ARE PLUGGED WITH A SCREW. ONLY IF THE UNIT HOLES ARE PLUGGED WITH A SCREW. ONLY IF THE UNIT
IS YOKE MOUNT AND HAS NO PHOTOCONTROL IS YOKE MOUNT AND HAS NO PHOTOCONTROL
RECEPTACLE MUST ANY ACTION BE TAKEN. THE SCREW RECEPTACLE MUST ANY ACTION BE TAKEN. THE SCREW
IN THE BEZEL IS TO BE REMOVED ONLY IF THE UNIT IS IN THE BEZEL IS TO BE REMOVED ONLY IF THE UNIT IS
FACING DOWN. ONE OF THE TWO SCREWS IN THE FACING DOWN. ONE OF THE TWO SCREWS IN THE
WIRING COMPARTMENT IS TO BE REMOVED ONLY IF THE WIRING COMPARTMENT IS TO BE REMOVED ONLY IF THE
UNIT IS FACING UP. CHOOSE THE SCREW THAT IS NOT UNIT IS FACING UP. CHOOSE THE SCREW THAT IS NOT
HOLDING DOWN THE CAPACITOR BRACKET.HOLDING DOWN THE CAPACITOR BRACKET.
BREATHING HOLESBREATHING HOLES
WIRINGWIRING
COMPARTMENTCOMPARTMENT POWER CORD POWER CORD
ENTRYENTRY
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL
AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
WARNING
CAUTION
!
!
2
1
1
2
7/16 Dia
25/32 Dia
YOKE
