Aerohive AP122 Installationshandbuch

AP122 Hardware User Guide

Read about and view specifications and compliance information for the AP122 in this topic. Install the

P122 using this topic

The AP122 is optimally suited for coverage-oriented, low-to-medium capacity environments. The AP122

features dual 2x2, 2-stream radios, providing dual 802.11n or 11n/ac performance with data rates up to

867 Mbps using existing 802.3af PoE infrastructure.

For more information about Aerohive APs in general, see "Introduction to Aerohive APs".

For information about connecting your APto the network, best-practices, and troubleshooting, see

"Basic Troubleshooting for New Devices"

Important! Changing the Country Code

If your access point is configured for the World Regulatory Domain, it is important to set the country

code to the country in which the APwill be deployed to meet regulatory requirements and for optimal

wireless operation. To do this, follow these steps:

The country code selection is for World models only and is not available to FCC, CAN, and

other country-specific models. Per FCC regulations, all Wi-Fi products marketed in the

United States must be set to U.S. channels only.

For Devices Running HiveManager:

1. Power on the APand allow it to find and connect to HiveManager. Once the APisconnected, it

appears in the table of unconfigured devices on the Monitor > Devices page and is categorized as

New under the Management Status table header.

2. Select the check box for the AP, and then choose Update > Advanced >Update Country.

3. On the Update Country Code page, choose the appropriate country code from the drop-down

list, and then click Upload.

Page 1 of 1

AP122 Hardware User Guid

201

For Devices Running HiveManager NG:

1. Power on the AP and allow it to find and connect to HiveManager NG. Once the APis connected

it appears in the table of devices on the Monitor > Devices page.

2. Select the check box next to the AP, and then choose Assign Country Code from the Actions drop-

down list. In the dialog box that appears, select the appropriate country from the drop-down list,

and then click Save.

3. Upload your changes to the device.

Regulatory Compliance Statements

The regulatory compliance statements in this section apply to AP122 devices.

For Japan, the AP122 is restricted for indoor use in the 5150-5350 MHz band only.

Compliance Statements

The following compliance information applies to the AP122.

R&TTE Directive

This device is compliant with the following directives:

• R&TTEDirective 1995/5/EC

AP122 Compliance Statement - Europe

EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The

following test methods have been applied in order to prove presumption of conformity with the

essential requirements of the R&TTE Directive 1999/5/EC:

IEC 60950-1:2005 +A1 +A2

Safety of Information Technology Equipment

EN 50385: / Article 3(1)(a) and Article 2 /EC)

Assessment of electronic and electrical equipment related to human exposure restrictions for

electromagnetic fields (0 Hz-300 GHz)

EN 300 328 V1.9.1:

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission

systems; Data transmission equipment operating using wide band modulation techniques;

Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive

EN 301 893 V1.8.1:

Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN

covering the essential requirements of article 3.2 of the R&TTE Directive

Page 2 of 1

AP122 Hardware User Guid

201

EN 301 489-1 V1.9.2:

Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility

(EMC) standard for radio equipment and services; Part 1: Common technical requirements

EN 301 489-17 V2.2.1

Electromagnetic compatibility and Radio spectrum Matters (ERM); Electromagnetic Compatibility

(EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission

Systems

In Italy the end-user should apply for a license at the national spectrum authorities in order to

obtain authorization to use the device for setting up outdoor radio links and/or for supplying

public access to telecommunications and/or network services.

•Česky [Czech]: [Aerohive] tímto prohlašuje, že tento [AP122] je ve shoděse základními

požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES.

•Dansk [Danish]: Undertegnede [Aerohive] erklærer herved, at følgende udstyr [AP122]

overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

•Deutsch [German]: Hiermit erklärt [Aerohive], dass sich das Gerät [AP122] in

Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen

Bestimmungen der Richtlinie 1999/5/EG befindet.

•Eesti [Estonian]: Käesolevaga kinnitab [Aerohive] seadme [AP122] vastavust direktiivi

1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

•English: Hereby, [Aerohive], declares that this [AP122] is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC.

•Español [Spanish]: Por medio de la presente [Aerohive] declara que el [AP130] cumple con

los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la

Directiva 1999/5/CE.

•Ελληνική [Greek]: ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [Aerohive] ΔΗΛΩΝΕΙ ΟΤΙ [AP122] ΣΥΜΜΟΡΦΩΝΕΤΑΙ

ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.

•Français [French]: Par la présente [Aerohive] déclare que l'appareil [AP130] est conforme

aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

•Italiano [Italian]: Con la presente [Aerohive] dichiara che questo [AP122] è conforme ai

requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

•Latviski [Latvian]: Ar šo [Aerohive] deklarē, ka [AP122] atbilst Direktīvas 1999/5/EK būtiskajām

prasībām un citiem ar to saistītajiem noteikumiem.

•Lietuvių[Lithuanian]: Šiuo [Aerohive] deklaruoja, kad šis [AP122] atitinka esminius reikalavimus

ir kitas 1999/5/EB Direktyvos nuostatas.

•Nederlands [Dutch]: Hierbij verklaart [Aerohive] dat het toestel [AP122] in overeenstemming

is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

•Malti [Maltese]: Hawnhekk, [Aerohive], jiddikjara li dan [AP122] jikkonforma mal-ħtiġijiet

essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

•Magyar [Hungarian]: Alulírott, [Aerohive] nyilatkozom, hogy a [AP122] megfelel a vonatkozó

alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

•Polski [Polish]: Niniejszym [Aerohive] oświadcza, że [AP122] jest zgodny z zasadniczymi

wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

•Português [Portuguese]: [Aerohive] declara que este [AP122] está conforme com os

requisitos essenciais e outras disposições da Directiva 1999/5/CE.

Page 3 of 1

AP122 Hardware User Guid

201

•Slovensko [Slovenian

]

: [Aerohive] izjavlja, da je ta [AP122] v skladu z bistvenimi zahtevami in

ostalimi relevantnimi določili direktive 1999/5/ES.

•Slovensky [Slovak]: [Aerohive] týmto vyhlasuje, že [AP122] spĺňa základné požiadavky a

všetky príslušné ustanovenia Smernice 1999/5/ES.

•Suomi [Finnish]: [Aerohive] vakuuttaa täten ettät [AP122] tyyppinen laite on direktiivin

1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter except in accordance with FCC multi-transmitter product procedures. If

this device operates in the 5.15~5.25 GHz frequency range, it is restricted to indoor use only.

IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of

7.8" (20 cm) between the radiator people or animals.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

Canada Regulatory ISED Statements:

This device complies with ISED (Innovation, Science and Economic Development) Canada

license-exempt RSS standard(s). Operation is subject to the following two conditions:

1. This device may not cause interference, and

Page 4 of 1

AP122 Hardware User Guid

201

This device must accept any interference, including interference that may cause undesired

operation of the device.

Le présent appareil est conforme aux CNR d’ ISED Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :

1. l'appareil ne doit pas produire de brouillage, et

2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

For products available in the USA/Canada market, only channel 1~11 can be operated. Selection

of other channels is not possible.

Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être

exploités. Sélection d'autres canaux n'est pas possible.

Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725

MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such

that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-

to-point operation as appropriate; and

(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority

users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause

interference and/or damage to LE-LAN devices.

Avertissement:

(i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une

utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de

satellites mobiles utilisant les mêmes canaux;

(ii) le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 à 5 350 MHz et

de 5470 à 5725 MHz doit être conforme à la limite de la p.i.r.e;

(iii) le gain maximal d'antenne permis (pour les dispositifs utilisant la bande de 5 725 à 5 850 MHz)

doit être conforme à la limite de la p.i.r.e. spécifiée pour l'exploitation point à point et

l’exploitation non point à point, selon le cas;

(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute

puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) pour les bandes 5250-

5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des

dommages aux dispositifs LAN-EL.

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment. Thisequipment should be installed and operated with minimum distance of 20 cm

between the radiator people and animals.

Page 5 of 1

AP122 Hardware User Guid

201

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20

cm de distance entre la source de rayonnement et des personnes ou des animaux.

Taiwan Compliance Information

Aerohive AP122

第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻率、加大

功率或變更原設計之特性及功能。

第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，

並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療

用電波輻射性電機設備之干擾。

在5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。

無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，發射的信號應維持

於操作頻帶中。

Taiwan MPE Warning

電磁波曝露量MPE標準值(MPE) 1mW/cm2，送測產品實值為0.734 mW/cm2

Radiation Exposure Statement:

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled

environment. Thisequipment should be installed and operated with minimum distance 20 cm

(7.8") between the radiator, and people or animals.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un

environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20

cm de distance entre la source de rayonnement et des personnes ou des animaux.

Taiwan Compliance Information - Aerohive AP122

第十二條→經型式認證合格之低功率射頻電機，非經許可，公司，商號或使用者均不得擅自變更頻率、加大

功率或變更原設計之特性及功能。

第十四條→低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，

並改善至無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療

用電波輻射性電機設備之干擾。

在5.25-5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。

Page 6 of 1

AP122 Hardware User Guid

201

無線資訊傳設備的製造廠商應確保

頻

率穩定性，如依製造廠商使用手冊上所述正常操作，發射的信號應維持

於操作頻帶中。

Taiwan MPE Warning - Aerohive AP122

電磁波曝露量MPE標準值(MPE) 1mW/cm2，送測產品實值為0.196868 mW/cm2

NCCStatement - Aerohive AP122

1. 「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率

或變更原設計之特性及功能」。

2. 「低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改

善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍

受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾」。

3. 「不致造成違反低功率電波輻射性電機管理辦法之所有控制、調整及開關之使用方法」。

4. 「對任何可能造成違反管理辦法規定之調整予以警告，或建議由具有發射機維修專長之技術人員執行或

由其直接監督及負責」。

5. 「對任何可能造成違反管理辦法之零件(晶體、半導體等)置換之警告」。

6. 「電磁波曝露量MPE標準值1mW/cm2，送測產品實測值為：0.196868 mW/cm2」。

7. 「本器材須經專業工程人員安裝及設定，始得設置使用，且不得直接販售給一般消費者」。

8. 「經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率

或變更原設計之特性及功能」。

Safety Guidelines

The information in this section applies to AP122 devices.

The following safety icons are used in these guidelines to identify the type of precaution:

This icon indicates a general caution. Failure to comply with a caution

notification can result in damage to equipment.

This icon indicates an electrical caution. Failure to comply with an electrical

notification can result in serious injury or death, and extensive damage to

equipment.

This icon indicates a laser caution. Failure to comply with a laser caution can

result in serious injury.

The following table lists the safety precautions you should follow when installing your AP122

devices.

Aerohive devices must be installed by a professional installer who is certified t

install these types of devices and to ensure that they are properly grounded

and meet applicable local and national electrical codes.

Page 7 of 1

AP122 Hardware User Guid

201

These devices are intended for indoor use only.

Do not install the device in an environment where the operating ambient

temperature might exceed the recommended ranges.

For products available in the USA/Canada market, for the 2.4 GHz band, only

channels 1-11 can be operated. Selection of other channels is not possible.

Changes or modifications made to this device that are not expressly approve

by the party responsible for compliance could void the user's authority to

operate the equipment.

Use only attachments and accessories specified by Aerohive.

These devices are not intended for use by persons (including children) with

reduced physical, sensory, or mental capabilities, or with lack of experience o

knowledge unless they are given supervision or instruction concerning use of t

devices by a person who is responsible for their safety. Children should be

supervised to ensure that they do not play with the devices.

Electrostatic discharge (ESD) can damage equipment and impair electrical

circuitry. ESD damage occurs when electronic components are improperly

handled and can result in complete or intermittent failures. Be sure to follow E

prevention procedures when handling electronic components and equipmen

During operation, the surfaces of the AP122 can become hot. Use caution wh

handling.

To meet federal radiation exposure requirements, these devices should be

installed at a minimum distance of 7.8" (20 cm) from people or animals.

Install the AP

You can mount the AP122 on a flat surface or wall, or on the rails of a standard dropped ceiling grid

using the hardware on the back of the chassis.

The following sections describe how to install your AP122 devices and connect them to the network.

Shipping Carton Contents

The AP122 access point shipping carton contains the following items:

• AP122 chassis

• Generic QuickStart Guide

• 3 wall-mount screws with anchors

Page 8 of 1

AP122 Hardware User Guid

201

Dropped Ceiling Mount

The following steps explain how to mount the AP122 on the rail of a dropped ceiling.

Make sure that you have all the materials and tools necessary, and familiarize yourself wit the

safety and site hazard warnings before you install the device. You may need to drill a small hole in

the adjacent ceiling tile to accommodate the cable. Before you begin, lift the ceiling tiles

adjacent to the location on the rail where you will install the device for better access. Once the

device is installed, you can slide it along the rail to better adjust its position.

Use the following steps to install your device to a dropped-ceiling rail.

1. For a dropped ceiling mount, use the mount tabs and clips on the bottom of the device.

2. Hold the device upside down and slip the mount tabs over the sides of the ceiling rail.

3. Press the device gently against the ceiling rail and rotate it until the mount clips click into

place.

Wall or Non-dropped Ceiling Mount

Use the built-in wall mount slots on the back of the chassis to attach the AP122 to any vertical or

horizontal surface (such as a wall or a drywall ceiling) that supports its weight (1.16 lb, or 0.56 kg),

and to which you can install wall mount screws. To mount the AP122 on a wall or other flat

surface, perform the following steps:

1. Make two marks where you want to mount the device on the wall or surface exactly 2.5" (64

cm) apart.

1. Drill two holes that are slightly smaller in diameter than the mounting screws.

2. Install two wall mount screws (and plastic anchors if necessary). The screw heads must

protrude far enough from the wall so that the chassis will slip over the screw heads, and leave

enough room to access the console connector. If you are connecting the device to cables

from inside the wall, drill an access hole for the cables.

3. Insert the heads of the screws into the large end of the wall mount slots and slide the device

down (or sideways for ceiling mounts) until the screws are seated in the narrow end of the

keyholes.

You can lock the device to the wall or ceiling using a security bracket that can be

ordered as an accessory.

4. To remove the device from the wall or ceiling, slide the chassis up until the screw heads slip

out of the wall mount slots.

5. The AP122 is PoE powered, so you must connect an Ethernet cable directly from the ETH0

port to a PoE-enabled switch or to a PoE injector.

You can also mount these devices to non-standard or recessed dropped ceiling tracks

using brackets designed for 9/16" (1.34 cm) tracks. These brackets can be ordered from

Aerohive (AH- ACC-BKT-80211AC-KIT). Not available in Brazil.

Page 9 of 1

AP122 Hardware User Guid

201

To remove the device, press the mount clips until they disengage from the rail, then rotate the

device and pull it away from the rail. A flat-blade screwdriver will make it easier to access and

press the clips.

Locking the AP

You can secure the AP using a Kensington® lock in the lock slot on the side of the device, or you

can use a security bracket and a crosshead screw or a security screw. Security brackets and

screws can be ordered separately from Aerohive (not available in Brazil).

Aerohive recommends a variety of Kensington locks. For more information, contact your sales

representative.

Connecting the AP to the Network

Follow these steps to connect your AP122 to PoE (power over Ethernet) power and to the network.

1. Connect a standard RJ45 Ethernet cable from ETH0 on the APto a switch.

2. If the switch provides PoE (power over Ethernet), cabling the APto the switch will power-on

the APin a few seconds. If the switch does not provide PoE, use a PoE injector. For more

information about Aerohive PoE injectors, contact your Aerohive representative.

3. After you power on the AP, it automatically tries to get network settings and contact

HiveManager NG. This process takes about five minutes. When you see the APlisted on the

All Devices page in the Monitor section of the HiveManager NG GUI, the initial setup is

complete and you can begin managing the AP with HiveManager NG.

Hardware Components

You can see the hardware components of the AP122 in the illustration below and read about them in

the sections that follow.

Page 10 of 1

AP122 Hardware User Guid

201

Removing the Device

Inhaltsverzeichnis

Andere Aerohive Drahtloser Zugangspunkt Handbücher

Aerohive

Aerohive HiveAP 320 Bedienungsanleitung

Aerohive

Aerohive HiveAP 320 Bedienungsanleitung

Aerohive

Aerohive AP130 Bedienungsanleitung

Aerohive

Aerohive HiveAP 330 Bedienungsanleitung

Aerohive

Aerohive HiveAP 340 Bedienungsanleitung

Aerohive

Aerohive HIVEAP 170 Bedienungsanleitung

Aerohive

Aerohive AP250 Bedienungsanleitung

Aerohive

Aerohive HiveAP 20 ag Kurzanleitung

Aerohive

Aerohive Atom AP30 Installationshandbuch

Aerohive

Aerohive access point Kurzanleitung

Aerohive

Aerohive HiveAP 28 Kurzanleitung

Aerohive

Aerohive AP245X Installationshandbuch

Aerohive

Aerohive HiveAP 340 Bedienungsanleitung

Aerohive

Aerohive HiveAP 100 Series Bedienungsanleitung

Aerohive

Aerohive AP630 Installationshandbuch

Aerohive

Aerohive AP150W Installationshandbuch

Aerohive

Aerohive AP370 Bedienungsanleitung

Aerohive

Aerohive AP330 Bedienungsanleitung

Aerohive

Aerohive HiveAP 20 Kurzanleitung

Aerohive

Aerohive AP1130 Bedienungsanleitung

Aerohive

Aerohive HiveAP 340 Bedienungsanleitung

Aerohive

Aerohive AP230 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung