AeroPure AP80RVL Bedienungsanleitung

MODEL: AP80RVL

BATHROOM FAN

www.aeropurefans.com

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, PLEASE READ THE FOLLOWING:

CAUTION

1. For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 2. This product is designed for installation

in ceilings up to a 12/12 pitch (45 degree angle). Duct connector must be horizontal. ** DO NOT MOUNT THIS PRODUCT IN A WALL.

3. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off power unit. 4. Please read

specification label on product for further information and requirements.

CLEANING & MAINTENANCE

For quiet and efficient operation, long life, and attractive appearance lower or remove grille and vacuum interior of unit with the

dusting brush attachment.

The motor is permanently lubricated and never needs oiling.

OPERATION

Use an on/off switch to operate this fan. See “Connect Wiring” for details.

PLAN THE INSTALLATION

1. Do not use in a cooking area.

2. Two ways to connect ductwork to a factory-shipped unit.

INSULATION*

(Place around and

ROOF CAP*

over Fan Housing.)

(with built-in

damper)

FAN

POWER

HOUSING

CABLE*

Keep duct

runs short

Seal gaps

around

Housing.

ROUND

DUCT*

WALL CAP*

Seal duct

(with built-in

*Purchase

joints with

ROUND

damper)

separately

tape.

ELBOW(S) *

READ AND SAVE THESE INSTRUCTIONS

Installer: Leave this manual with the homeowner.

1.Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number

listed in the warranty. 2.Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power

from being switching on accidentally. If the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel. 3. Installation work and electrical wiring must be done by a licensed person(s) in accordance with all applicable codes and

standards, including fire-rated construction codes and standards. 4. Sufficient air is needed for proper combustion and exhausting of gases through

the flue (chimney) of fuel burning equipment to prevent backdraft. Follow the heating equipment manufacturer’s guideline and safety standards such

as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities. 5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden

utilities. 6. Ducted fans must always be vented to the outdoors. 7. Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault

Circuit Interrupter) - protected branch circuit. 8. This unit must be grounded. 9. Never place a switch where it can be reached from a tub or shower.

10. Not for use in kitchens. 11. Install fan at least 2.5 m (8.2 feet) above the floor. 12. WARNING: To reduce the risk of fire or electric shock,

do not use this fan with any solid-state speed control device. 13. The fan must not be installed in a ceiling thermally insulated to a value greater than

R40.

ASSEMBLY INSTRUCTIONS

1. Before installation, you need to know:

Screw A

ST4.2*1/2"

Screw B

ST4.2*1"

Hanger bar

13 3/8"

(long)

14 3/8 in.-23 1/2 in. (365-597)

1. MOUNT WITH HANGER BARS

1a. Sliding hanger bars have been provided, which allow the housing to

be positioned accurately anywhere between the framing. The bars may

be used on all types of framing: I-joist, standard joist, and truss

construction. Slide hanger bars onto housing and adjust as needed to fit

between framing.

1b. Extend the hanger bars to the width of the framing. Position the

Screw A

fan with the hanger bar tabs aligned with the bottom edge of the framing,

holding the ventilator in place.

Secure hanger bars to framing using one screw on each end of hanger

bar. Attach set screws to lock bar hangers in place.

Screw B

2. INSTALL ROUND DUCTWORK

Connect the round ductwork (not included) to the damper/duct connector,

and run the ductwork to a roof or wall cap (not included). Using duct tape

(not included), secure all the ductwork connections so that they are air

tight. Insulated flexible duct is recommended for the quietest possible

installation. A 1 –3 foot run of rigid duct- followed by insulated flexible

duct- will ensure quietest operation.

CONNECT ELECTRICAL WIRING

Run 120 Volts AC house wiring to the fan. Use only UL-approved connectors (not included) to attach the house wiring to the

wiring plate. Refer to the wiring diagram, and connect the wires as shown.

BLACK(BLK)

WHITE(WHT)

BLUE(BLU)

GROUND (GRD)

LIGHT

WIRE PANEL

UNIT

FAN

SWITCH BOX

FAN

LIGHT

RECEPTACLE

POWER SUPPLY

120V AC

Aero Pure AP80RVL

READ AND SAVE THESE INSTRUCTIONS

Installer: Leave this manual with the homeowner.

FINISH CEILING WORK

1. A round ceiling hole 6 1/2 inches (165mm) diameter should be cut.

Seal any gap between the hole in the drywall and the fan with sealant.

2. Install the compact florescent bulb or LED bulb. Bulb not included.

3. The bulb housing can adjust up or down to accommodate different

bulbs. Unit is qualified with use of G24 adaptor and use of a GU24

bulb.

Lamp base

Wing nut

Fluorescent lamp

Joist

Hanger

bar

Ceiling

After finishing the ceiling job, fill gap between flange and ceiling with

caulk or other sealant to prevent air leakage.

REPLACEMENT INSTALLATION

1. Remove the trim ring by detaching the springs.

2. Remove the screws as shown in the right.

3. Remove the lamp base.

4. Pull the duct system so that you can see the blower

system.

Remove the screws

Blower system

Lamp base

REPLACEMENT INSTALLATION

5. Remove the screws as shown on the right.

Remove the screws

6. Remove the blower system from of the housing.

7. Replace the broken parts.

Remove the screws

REPLACEMENT INSTALLATION

8. To replace the capacitance remove the wire panel, and then

replace the capacitance.

Remove

the screws

Wire Panel

Aero Pure AP80RVL

SERVICE PARTS

PART

PART NAME

Qty.

Trim Ring

Grille Spring

Lamp base

Wire Panel / Harness Assembly

Hanger Bars

Wiring plate

Motor

Motor plate

Blower Wheel

Blower housing

Duct

Housing

WARRANTY

READ AND SAVE THESE INSTRUCTIONS

Installer: Leave this manual with the homeowner.

This warranty covers all defects in workmanship or materials for:

The mechanical and electrical parts contained in this product for a period of 72 months from the date of purchase. You

must keep and be able to provide your original sales receipt as proof of date of purchase. This warranty is covered to the

original retail purchaser of this product only. The manufacturer will replace any mechanical or electrical part that proves

defective in normal household use for a period of 72 months.

THIS WARRANTY DOES NOT COVER:

• Damages from improper installation.

• Damages from shipping.

• Damages from misuse, abuse, accident, alteration, lack of proper care and maintenance.

• Damages from service by persons other than a licensed electrician.

• Does not cover any labor or transportation charges related to the repair of this product.

This warranty does not extend to fluorescent lamp starters and tubes or any light bulbs..

THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING

THE WARRANTIES OF MERCHANTABILITYAND FITNESS FOR APARTICULAR PURPOSE.

The remedy provided in this warranty is exclusive and is granted in lieu of all other remedies. This warranty does not

cover incidental or consequential damages. Some states do not allow the exclusion of incidental or consequential

damages, so this limitation may not apply to you. Some states do not allow limitations on how long an implied warranty

lasts, so this limitation may not apply to you. This warranty gives you specific legal rights; you may also have other rights

that vary from state to state.

Aero Pure AP80RVL

Inhaltsverzeichnis

Andere AeroPure Lüfter Handbücher

AeroPure

AeroPure ABF110DHG6 Series Bedienungsanleitung

AeroPure

AeroPure ABF110DHG5 Series Bedienungsanleitung

AeroPure

AeroPure AP80-QVL Bedienungsanleitung

AeroPure

AeroPure AP90-SG6W Bedienungsanleitung

AeroPure

AeroPure AP70-S Bedienungsanleitung

AeroPure

AeroPure AP50-G1W Bedienungsanleitung

AeroPure

AeroPure CP80S Series Bedienungsanleitung

AeroPure

AeroPure AP90-SL Bedienungsanleitung

AeroPure

AeroPure VSF110DMH-S Bedienungsanleitung

AeroPure

AeroPure AP904-SL Bedienungsanleitung

AeroPure

AeroPure AP100-S Bedienungsanleitung

AeroPure

AeroPure AP200D-S Bedienungsanleitung

AeroPure

AeroPure AP90-S Bedienungsanleitung

AeroPure

AeroPure AP50-S Bedienungsanleitung

AeroPure

AeroPure VSF110D-S Bedienungsanleitung

AeroPure

AeroPure CP70-SL Bedienungsanleitung

AeroPure

AeroPure AP120H-S Bedienungsanleitung

AeroPure

AeroPure VSF110DH-S Bedienungsanleitung

AeroPure

AeroPure AP80H-RVL Bedienungsanleitung

AeroPure

AeroPure ABF110DHG1 Series Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung